No description available.

[pt] Neste trabalho são apresentados dois reflectômetros ópticos por contagem de fótons no domínio do tempo para o monitoramento de fibras ópticas. O primeiro foi projetado para obter faixas dinâmicas altas. Demonstrou-se a sua capacidade de sintonização no monitoramento de redes passivas WDM-PON durante o tráfego de dados. 32 dB de faixa dinâmica com 6 m de resolução foram atingidos. O segundo reflectômetro foi projetado para atingir resoluções ultra altas. As aplicações neste caso, além do monitoramento de uma rede TDM-PON de curto alcance, foram na caracterização de redes de Bragg dispersivas e na descrição e modelagem de um fenômeno não reportado antes na literatura, chamado nesta tese de reflexão por curvatura. Foi demonstrada uma resolução menor que 3 cm com faixa dinâmica maior que 14.0 dB. / [en] This thesis presents the development of two photon counting optical time domain reflectometers for fiber optic links monitoring. The first one was focused on high dynamic range. It is demonstrated its tunable capability for a WDM-PON in-service monitoring. 32 dB on dynamic range and a two-point resolution of 6 m is achieved. The second reflectometer was design to accomplish an ultra high resolution. The monitoring of a short TDM-PON is performed. Moreover, due to its high resolution, a chirped fiber Bragg grating is characterized and a non previous reported phenomena, the bend reflection, is shaped and described. It is demonstrated 3 cm two-point resolution and more than 14 dB on dynamic range.

MnSi(111) films were grown on Si(111) substrates by solid phase epitaxy (SPE) and molecular beam epitaxy (MBE) to determine their magnetic structures. A lattice mismatch of -3.1% causes an in-plane tensile strain in the film, which is partially relaxed by misfit dislocations. A correlation between the thickness dependence of the Curie temperature (TC) and strain is hypothesized to be due to the presence of interstitial defects. The in-plane tensile strain leads to an increase in the unit cell volume that results in an increased TC as large as TC = 45 K compared to TC = 29.5 K for bulk MnSi crystals. The epitaxially induced tensile stress in the MnSi thin films creates an easy-plane uniaxial anisotropy. The magnetoelastic coefficient was obtained from superconducting quantum interference device (SQUID) magnetometry measurements combined with transmission electron microscopy (TEM) and x-ray diffraction (XRD) data. The experimental value agrees with the coefficient determined from density functional calculations, which supports the conclusion that the uniaxial anisotropy originates from the magnetoelastic coupling. Interfacial roughness obscured the magnetic structure of the SPE films, which motivated the search for a better method of film growth. MBE grown films displayed much lower interfacial roughness that enabled a determination of the magnetic structure using SQUID and polarized neutron reflectometry (PNR). Out-of-plane magnetic field measurements on MBE grown MnSi(111) thin films on Si(111) substrates show the formation of a helical conical phase with a wavelength of 2?/Q = 13.9 ± 0.1 nm. The presence of both left-handed and right-handed magnetic chiralities is found to be due to the existence of inversion domains that result from the non-centrosymmetric crystal structure of MnSi. The magnetic frustration created at the domain boundaries explains an observed glassy behaviour in the magnetic response of the films. PNR and SQUID measurements of MnSi thin films performed in an in-plane magnetic field show a complex magnetic behaviour. Experimental results combined with theoretical results obtained from a Dzyaloshinskii model with an added easy-plane uniaxial anisotropy reveals the existence of numerous magnetic modulated states that do not exist in bulk MnSi. It is demonstrated in this thesis that modulated chiral magnetic states can be investigated with epitaxially grown MnSi(111) thin films on insulating Si substrates, which offers opportunities to investigate spin-dependent transport in chiral magnetic heterostructures based on this system.

Pour un réacteur à eau pressurisée, la contamination radioactive du circuit primaire constitue un problème majeur pour les opérations de maintenance. La principale source de cette contamination est le relâchement des produits de corrosion des tubes GV en alliages base nickel représentant environ les trois quarts de la surface totale du circuit primaire. L’oxydation des alliages base nickel en milieu primaire, à l’origine du relâchement, a fait l’objet de nombreuses études. Certaines pistes d’amélioration ont d’ailleurs d’ores et déjà été explorées comme la métallurgie des tubes et plus précisément leur état de surface, la pré-oxydation, l’addition de zinc au sein du milieu primaire. Cependant, la compréhension du phénomène demeure lacunaire. La nature et la structure de la couche d’oxyde formée sur les alliages base nickel est relativement bien connue, mais pas sa cinétique de formation et de relâchement ou de façon bien moins précise. L’objet principal de cette étude est donc le développement et la mise en œuvre d’un dispositif expérimental innovant permettant de suivre l’épaisseur d’oxyde formée par une mesure optique de réflectométrie in situ, ainsi que le relâchement en ligne par mesure de concentration par ICP – MS. Les échantillons utilisés lors des différents essais expérimentaux ont également été analysés par diverses techniques notamment l’XPS et le MET afin d’apporter de nouveaux éléments sur la nature ou la structure des couches d’oxyde. En outre, ces analyses, permettant également d’évaluer les épaisseurs d’oxyde ont contribué à valider les résultats d’oxydation obtenus par réflectométrie. L’utilisation de ce moyen expérimental a permis d’obtenir des résultats, certes peu nombreux mais aux perspectives prometteuses. / The radioactive contamination is a significant issue for the maintenance of the primary loop of a water pressurized reactor. The corrosion products released by steam generators tubes made of nickel base alloys, which represent seventy five percent of the whole primary loop surfaces, are highly responsible for this pollution. The oxidation of nickel base alloys in primary water is thus a widely studied subject. Besides, some mitigation means have already been performed like the control of tube manufacturing and of their surface state in particular, a pre-oxidation process, the injection of zinc into primary water. However, the phenomenon remains deficiently understood. The oxide layer nature and structure, formed on nickel base alloys is relatively well known, but this knowledge is far less precise about the layer formation and release kinetics. The main subject of this study is thus to develop an innovative experimental facility which permits to obtain the layer thickness by in situ optical reflectometry measurements, and the corrosion products release by concentration ICP – MS in line measurements. The implementation of these two techniques has needed lots of theoretical and technical adjustments, especially in situ way of using the reflectometry. Some analyses, XPS and MET in particular, have been performed on the different used samples to bring new facts about the nature and structure of oxide layers. Moreover, these analyses have contributed to validate the oxidation results, by measuring the oxide layer thickness and comparing it to the reflectometric results. The different tests realized with this new experimental device are quite promising and should be used and improved to perform others valuable tests.

L’étude des nystagmus du nourrisson est difficile pour des raisons méthodologiques. La plupart des études sont donc réalisées chez des adultes et a posteriori. Ces études chez l’adulte ont permis la révision des classifications des nystagmus infantiles, avec la consolidation des concepts de syndrome du nystagmus précoce et de nystagmus de type latent. La séméiologie et l’étiopathogénie des nystagmus du nourrisson – notamment des formes comportant un élément vertical et des formes transitoires – reste donc à étudier. Dans ce but : 1. Nous avons développé de nouvelles techniques d’enregistrement des mouvements oculaires chez les nourrissons, utilisables dans le cadre d’une consultation. Elles incluent de nouveaux stimuli, un appareil d’enregistrement des mouvements oculaires spécialement conçu pour le nourrisson et de nouvelles méthodes d’analyse statistique du signal. Nous avons vérifié la faisabilité de ces enregistrements chez 28 nourrissons atteints de nystagmus. 2. Nous avons étudié systématiquement 32 cas de nystagmus de type spasmus nutans, classiquement considéré comme une entité bénigne idiopathique, avec un examen clinique complet, une imagerie cérébrale, une électrophysiologie visuelle et des enregistrements oculo-moteurs. Dans 53,1% des cas, le spasmus nutans était le symptôme d’une autre maladie : neurologique (34,3%), notamment des gliomes du chiasma (21,9%), ou rétinienne (12,5%). Une atteinte des voies visuelles antérieures est probablement en cause dans la physiopathologie des spasmus nutans. 3. Huit cas de nystagmus ayant conduit au diagnostic de gliome des voies optiques (GVO) ont été également enregistrés et étudiés. L’âge d’apparition du nystagmus allait de 2,5 à 10 mois. Le GVO était toujours chiasmatique et constituait une sous-population spécifique. Le nystagmus était toujours de type spasmus nutans. Les enregistrements oculo-moteurs montraient : une fréquence entre 2,7 et 5 Hz, une morphologie sinusoïdale du nystagmus, une dissociation et une dysconjugaison particulière, avec une opposition de phase (180°) entre les oscillations des deux yeux dans le plan horizontal mais une correspondance de phase dans le plan vertical, à l’origine d’un mouvement semblable à un mouvement de convection. Rarement et brièvement, le rapport de phase changeait. Ces caractéristiques orientent vers des oscillations dans le système des vergences, possiblement la conséquence d’une atteinte des afférences sensorielles des centres du contrôle vergentiel dans le tronc cérébral, secondaire au GVO et survenant pendant la période sensible du développement visuel. 4. Cinq cas de nystagmus upbeat chez des nourrissons avec des rétines et une imagerie cérébrale normale ont été étudiés. Le nystagmus était observé en décubitus et électivement déclenché par des rotations de la tête en position allongée. Dans tous les cas, une résolution spontanée était observée après quelques mois d’évolution. Les caractéristiques de ce type de nystagmus suggèrent une participation du système otolithique, suivie d’une recalibration secondaire des circuits vestibulo-oculaires. En conclusion, le développement de techniques d’enregistrement des mouvements oculaires adaptées aux nourrissons aide à la compréhension de l’étiopathogénie de variétés mal décrites de nystagmus, notamment dans les cas comportant un élément vertical et dans les cas transitoires. Les processus de maturation des voies visuelles antérieures et des centres de contrôle de l’oculomotricité semblent jouer un rôle central dans les mécanismes de ces nystagmus. / Studying infantile nystagmus during infancy is difficult for methodological reasons. Most such studies have been performed in adults and a posteriori. These studies in adults allowed for an improvement in the existing classifications, with now robust knowledge about the two most frequent varieties of infantile nystagmus: infantile nystagmus syndrome and fusion maldevelopment nystagmus syndrome. The characteristics and pathophysiology of nystagmus in infants–notably varieties of nystagmus with a vertical component and transitory nystagmus– need further study. For this reason: 1. We developed new techniques for the recording of eye movements in infants in the setting of a clinic. They include new stimuli, the use of specially-designed infrared photo-oculography eyetrackers and new statistical analysis paradigms. We assessed these techniques in a population of 28 infants with a nystagmus. 2. We systematically studied 32 cases of spasmus nutans, classically considered an idiopathic entity, with comprehensive clinical examination, brain imaging, electrophysiology, nystagmus recording. In 53.1% of cases, it led to the diagnosis of another condition: a neurological disease (34.3%), including cases of chiasmal gliomas (21.9%), or a retinal dysfunction (12.5%). Anterior visual pathway dysfunction is likely involved in the pathophysiology of spasmus nutans. 3. Eight cases of nystagmus having led to a diagnosis of optic pathway glioma (OPG) were also recorded and studied. Age at nystagmus onset was 2.5-10 months. The associated OPG always involved the chiasm, and represent a specific subpopulation of OPG. Clinically, the nystagmus was always classified as spasmus nutans type. Oculographic recordings showed frequencies of 2.7-5 Hz, sinusoidal waveforms, dissociation and a special type of disconjugacy, with a 180° horizontal phase shift and no vertical phase shift, exhibiting a “convection-like” movement pattern. Rarely and for short periods of time, the phase shift could change. These characteristics point towards oscillations in the vergence system, which could possibly result from the specific disruption of the vergence centres afferences in the brainstem, induced by the OPG during the sensitive period of visual development. 4. Five cases of upbeat nystagmus in infants with normal retinas and normal brain imaging were studied. The nystagmus mostly occurred in supine position and could be triggered by head rotations in the supine position. All resolved spontaneously. The characteristics of this nystagmus suggest an involvement of the otolithic system, with a secondary recalibration of the vestibulo-ocular pathways. In conclusion, the development of infant-friendly devices for eye-movements recording helps providing new insights on the pathophysiology of poorly described varieties of nystagmus, including nystagmus with a vertical component and transitory nystagmus. The maturation process of both the anterior visual pathways and the oculomotor pathways appears to be central in the mechanisms of these nystagmus.

Devido à importância do monitoramento da composição iônica da solução do solo, no que diz respeito ao meio ambiente e ao manejo da fertirrigação, associada às limitações práticas dos métodos tradicionais de sua determinação é crescente a procura por um método confiável que possibilite o monitoramento desta composição em tempo real e em curtos intervalos de tempo. Neste sentido a TDR tem sido uma alternativa viável. O presente trabalho objetivou, pelo uso da TDR, avaliar o desempenho de sete modelos na determinação da CEw; relacioná-los com a concentração dos íons potássio nitrato e cloreto avaliando os modelos em determinar a concentração dos íons; e por fim monitorar e determinar a concentração destes íons na água lixiviada em coluna de solo não saturado. O trabalho foi divido em dois experimentos, no primeiro os modelos foram calibrados em colunas de solo sendo formado por 24 tratamentos composto por 4 faixas de umidade volumétrica e 6 concentrações da solução de KCl. Para cada coluna de solo era realizada uma leitura com a TDR ( e CEa) e a CEw na solução do solo era determinada por condutivímetro de mesa, nesta solução foram determinadas as concentrações de potássio e cloreto. No segundo experimento o mesmo procedimento foi realizado, entretanto, foi aplicado KNO3 e determinados potássio e nitrato. Desta forma, foi possível calibrar os modelos para a estimativa da CEw, e para determinação das concentrações dos íons potássio, nitrato e cloreto. Os modelos foram avaliados pelos coeficientes de determinação (R²) e exatidão (d), pela estimativa do erro padrão (EEP) e, ainda, foram classificados de acordo com o índice c, produto dos dois coeficientes citados. Os resultados mostram que os modelos de Rhoads et al. (1976) e Vogeler et al. (1996) se ajustam melhor para solos com características texturais argilosas sendo classificados como Ótimos métodos para a determinação da CEw, tanto pela aplicação de KCl como pela aplicação de KNO3 via água de irrigação. Na estimativa da CEw no solo arenoso os modelos de Munõz-Carpena et al. (2005), Mualen e Friedman (1991), Vogeler et al. (1996) e Rhoads et al. (1976) apresentam melhores ajustes na determinação da CEw, sendo classificados com Muito bom. Na determinação do potássio pelos modelos avaliados o melhor ajuste se dá pela associação da relação K-CEw do tipo potência aplicada para solos argilosos e linear para solos arenosos, apresentando classificação de: Ótimo e Muito bom, respectivamente. Para o cloreto e o nitrato o melhor ajuste se dá pela relação de CEw-Cl e CEw-NO do tipo linear, apresentando classificação de Muito Bom e Ótimo respectivamente. A TDR é uma técnica confiável no monitoramento da concentração dos íons potássio e cloreto lixiviados no perfil do solo. / There is a growing demand for a reliable method applied to monitoring ionic composition of soil solution in real-time and short time intervals, due the importance to environmental sustainability and fertigation management and limitations of traditional methods for determination. Time domain reflectometry (TDR) is often considered a viable alternative to traditional methods. Consequently, this research looks for using TDR evaluate the performance of seven mathematical models for determining electrical conductivity (CEw) by comparing simulated and measured concentrations of potassium, nitrate and chloride, and to monitor and determine the concentration of these ions in water leached from unsaturated soil columns. The research was carried out under two experiments conditions. In the first experiment the models were calibrated with input data from 24 soil columns consisting of four soils with six different KCl concentrations. For each soil column CEw was determined by both TDR ( and CEa readings) and the CEw of soil solution was determined by direct measurements of potassium and chloride concentrations. In the second experiment the procedure was the same, but with KCl being replaced with KNO3. This was possible to calibrate the models to estimate the CEw, and to determine potassium, nitrate and chloride ions concentrations. The models were ranked using the c-index, the coefficient of determination (R²) and estimated standard error (ESE). The results showed were Rhoads et al. (1976) and Vogel et al. (1996) classified as \"Great\" for the CEw determination associated with the application of both KCl and KNO3 to irrigation water in clay soils. For estimating CEw in sandy soils, the models Muñoz-Carpena et al. (2005), Mualen and Friedman (1991), Vogel et al. (1996) and Rhoads et al. (1976) were classified as \"Very Good.\" The relationship between CEw and potassium concentration was best represented by a power function in clay soils, and a linear function in sandy soils, with index of \"Great\" and \"Very Good\", respectively. For chloride and nitrate, the best fits were obtained by representing the CEw-Cl and CEw-NO3 relationships with linear functions, which were classified as Very Good and Good, respectively. TDR proved to be a reliable technique for monitoring the concentration of potassium and chloride ions leached in soil profiles.

Verankerte Polymere können die Funktionalität einer Oberfläche beeinflussen. Der Schwerpunkt dieser Arbeit liegt auf der Untersuchung von Polymerbürsten aus Polyacrylsäure (PAA) und Poly(N,N-dimethylaminoethyl methacrylat) (PDMAEMA). Auf Oberflächen, die mit PAA Bürsten beschichtet sind, können Proteine im nativen Zustand immobilisiert werden. Für PDMAEMA ist eine Reaktion auf externe Reize bekannt. So kann dessen untere kritische Lösungstemperatur (LCST) zur Einstellung der Hydrophobizität von Oberflächen verwendet werden. Erstmalig im Rahmen dieser Arbeit wurde untersucht, wie sich hydrostatischer Druck von bis zu 1000 bar auf die Funktionalität der verwendeten Polymerbürsten auswirkt. Aus Diblock-Kopolymeren wurden Langmuir-Filme unterschiedlicher Ankerdichte mit der Langmuir-Schäfer Technik auf feste Substrate übertragen. Die Funktionalität der PAA Bürsten wurde vor und nach der Adsorption von Rinderserumalbumin (BSA) in gepufferter D2O-Lösung mit Hilfe der Neutronenreflektometrie (NR) bei 1 bar und 900 bar an der fest-flüssig Grenzfläche untersucht. Es wurden Volumenfraktionsprofile der PAA Bürste und adsorbierten BSA extrahiert, woraus sich eine lineare Abhängigkeit zwischen Ankerdichte und Menge an adsorbiertem Protein feststellen ließ. Erhöhung des hydrostatischen Druckes auf 900 bar veränderte weder die PAA Volumenprofile noch die Immobilisierung von BSA. Die PDMAEMA Bürsten wurden mittels NR bei Temperaturen von 20-60 °C und Drücken von 1-1000 bar untersucht. Zur Analyse der Daten wurde ein neuartiges Dichteprofil-Modell verwendet. Temperaturerhöhung führt zur stetigen Abnahme der Bürstendicke. Dies lässt sich durch den LCST induzierten Phasenübergang der Polymere vom hydrophilen in einen hydrophoben Zustand erklären. Es wurde gefunden, dass eine Erhöhung des hydrostatischen Druckes diesem Prozess entgegenwirkt. Strukturänderungen der Polymerbürsten bei Erhöhung der Temperatur um 10 K ließen sich durch Erhöhung des Druckes um 1000 bar rückgängig machen. / The functionality of an interface can be modified by polymer brushes. The focus of this work is on brushes of either polyacrylic acid (PAA) or poly(N,N-dimethylaminoethyl methacrylate) (PDMAEMA). PAA brushes provide a soft interface that prevents the denaturation of adsorbed proteins. PDMAEMA is known to respond to external stimuli. The lower critical solution temperature (LCST) of PDMAEMA can be used to tune the hydrophobicity of the interface with temperature. For the first time, the effect of elevated hydrostatic pressure, up to 1000 bar, on the functionality of these systems is investigated. Planar PAA and PDMAEMA brushes are prepared from precursor diblock copolymer Langmuir layers with varied grafting density utilizing the Langmuir-Schäfer transfer technique. For solvent-swollen PAA brushes, neutron reflectivity (NR) measurements are conducted at the solid-liquid interface after incubation in buffered D2O and after the adsorption of bovine serum albumin (BSA) from the aqueous liquid phase at 1 bar and 900 bar. Detailed volume fraction profiles of the PAA brush and adsorbed BSA proteins are extracted. The amount of adsorbed BSA is found to scale linearly with grafting density. An elevated hydrostatic pressure of 900 bar is found to have no impact on the structure of the PAA brush and its capability to bind BSA proteins. The PDMAEMA brushes are investigated by NR at the solid-liquid interface in a temperature range of 20 to 60 °C for hydrostatic pressures from 1 to 1000 bar. A novel theoretical model of the brush density profile is used to fit the experimental NR data. Increasing the temperature causes a continuous decrease of the polymer brush thickness due to a hydrophobic coil to globule transition of the polymer chains when crossing the LCST. Hydrostatic pressure is found to act antagonistic to temperature. The hydrophobic collapse of the PDMAEMA brush caused by a temperature increase of 10 K is counterbalanced by a pressure increase of 1000 bar.

O desenvolvimento econômico e o aumento da produtividade agrícola intensificaram o uso de produtos químicos nas lavouras. Quando se pretende quantificar o impacto ambiental de tal uso é necessário empregar modelos que descrevam o fluxo de água e solutos na região não saturada do solo. Para esse fim, um dos parâmetros mais eficazes é conhecer a retenção de água no solo. O objetivo deste trabalho foi desenvolver funções de pedotransferência (FPTs) que estimassem a partir de análise em redes neurais artificiais (RNAs) a retenção de água nos solos da microbacia hidrográfica do ribeirão Canchim, município de São Carlos, SP. Os atributos físicos, textura (argila, silte e areia), densidade e resistência à penetração dos solos: LVAd, LVe, LVdf e NVef, manejados com e sem cobertura vegetal e sob mata foram determinados com equipamentos não convencionais na Embrapa Instrumentação Agropecuária em São Carlos, SP. Esses parâmetros foram utilizados como variáveis de entrada nas duas redes neurais artificiais. Foram obtidas, ainda, as curvas de retenção de água no solo por meio da câmara de pressão de Richards e da tomografia computadorizada, além da porosidade total e da condutividade hidráulica não saturada. O analisador granulométrico de solos e o penetrômetro associado a TDR possibilitaram a obtenção de um grande número de dados. Os atributos físicos dos solos apresentaram grande variabilidade em função da constituição granulométrica e manejos adotados. As RNAs foram eficientes no desenvolvimento de FPTs capazes de estimar a retenção de água com base em propriedades básicas de solo obtidas em grande número. / Economic development and increasing agricultural productivity have intensified the use of chemical products in farming. The quantification environmental impact of these products requires the use of models that describe the flow of water and solutes in the unsaturated region of the soil. For this purpose, one of the most effective parameters belong to the water retention curve of the soil. The purpose of this work was to develop pedotransfer functions (PTFs) to estimate the retention of water by soils of the hydrographic microbasin of the Canchim river, in the municipality of São Carlos, state of São Paulo, Brazil, based on artificial neural networks (ANNs). The physical attributes, granulometry (clay, silt and sand), density and resistance to penetration of LVAd, LVe, LVdf and NVef soils, managed with and without vegetal cover and under forest, were determined using nonconventional equipment at Embrapa Instrumentação Agropecuária in São Carlos, SP. These parameters were used as input variables for two artificial neural networks. The soils\' water retention curves were also obtained using a Richards pressure chamber and computed tomography, as well as their total porosity and unsaturated hydraulic conductivity. A soil granulometric analyzer and a penetrometer allied to TDR provided a large number of data. The soils\' physical attributes displayed a wide variability as a function of their granulometric constitution and adopted managements. The ANNs were effective in developing PTFs able to estimate the water retention based on the large number of basic soil properties.

A reflectometria no domínio do tempo permite estimar o teor de umidade de um meio através da sua correlação com a constante dielétrica. Uma sonda helicoidal TDR, que pode ser cravada em conjunto outros ensaios de penetração in situ para a estimativa do teor de umidade em diversas profundidades, tem aplicação interessante para a investigação geotécnica do subsolo. No presente trabalho, uma sonda TDR foi adaptada e utilizada em conjunto ao ensaio CPT para caracterização de um perfil de solo arenoso não saturado que ocorre na região de Bauru (SP). A calibração dessa sonda foi feita em laboratório especificamente para esse solo. As equações de calibração que mostraram os melhores resultados foram definidas correlacionando a constante dielétrica, condutividade elétrica aparente e a massa específica seca com o teor de umidade. Com o intuito de melhorar a acurácia na determinação do teor de umidade em campo e eliminar possíveis interferências no registro da onda eletromagnética, foram efetuadas modificações em algumas características do projeto original dessa sonda. Tais modificações consistiram em separar os eletrodos condutores e as partes metálicas da sonda, e eliminar o cabo coaxial de extensão, conectando a sonda diretamente a um cabo coaxial de 12 m de comprimento. Tais mudanças levaram a uma melhoria significativa na determinação do perfil de teor de umidade do local estudado. Os valores de teor de umidade de campo determinados usando o TDR ao longo de 8 m de profundidade foram comparados com os valores de referência obtidos de amostras deformadas retiradas com trado mecânico. O erro médio na estimativa do perfil de teor de umidade gravimétrico utilizando a sonda TDR helicoidal foi de 1.61%, na última campanha de ensaios realizados. Os resultados dessa pesquisa indicam que esta ferramenta é adequada para estimar do perfil de teor de umidade para uso em conjunto com o ensaio CPT. / The time domain reflectometry allows estimating the moisture content of a medium by means of its correlation with the dielectric constant. A coil TDR probe, which can be driven into the ground together with others in situ penetration tests, can be used to estimate the moisture content at different depths. It is an interesting approach for geotechnical site characterization. In this work, a coil TDR probe was adapted and used in combination with the CPT test for the site characterization of an unsaturated sandy soil profile which occurs in the region of Bauru (SP). The probe calibration was performed in laboratory specifically for that soil. The calibration equation, which presented the best results, were defined correlating the dielectric constant, electrical conductivity and dry density with the moisture content. In order to improve the accuracy for determining the water content in the field and to eliminate possible interference on the electromagnetic wave registration, modifications were made in some characteristics of the original design of this probe. Such modifications consisted in separating the conductive electrodes from the metal parts of the probe, and eliminating the coaxial extension cable, connecting the probe directly to a coaxial cable 12 m long. Such changes have led to a significant improvement in the determination of the moisture content profile of the studied site. The moisture content values determined in situ by using the TDR along 8 m depth were compared with reference values obtained from disturbed soil samples collected using mechanical augers. The root mean square error of the gravimetric water content profile using the TDR coil probe was 1.61% in the last test campaign. The results of this research indicate that this tool is suitable to estimate the gravimetric moisture content together with the CPT test.

Polymer/inorganic nanoparticle hybrid thin films, primarily composed of functional inorganic nanoparticles, are of great interest to researchers because of their interesting electronic, photonic, and optical properties. In the past two decades, layer-by-layer (LbL) assembly has become one of the most powerful techniques to fabricate such hybrid thin films. This method offers an easy, inexpensive, versatile, and robust fabrication technique for multilayer formation, with precisely controllable nanostructure and tunable properties. In this thesis, various ways to control the structure of hybrid thin films, primarily composed of polyelectrolytes and indium tin oxide (ITO), are the main topics of study. ITO is one of the most widely used conductive transparent oxides (TCOs) for applications such as flat panel displays, photovoltaic cells, and functional windows. In this work, polyethyleneimine (PEI) was used to stabilize the ITO suspensions and improve the film buildup rate during the LbL assembly of poly(sodium 4-styrenesulfonate) (PSS) and ITO. The growth rate was doubled due to the stronger interaction forces between the PSS and PEI-modified ITO layer. The assembly of hybrid films was often initiated by a polyelectrolyte precursor layer, and the characteristics of the precursor layer were found to significantly affect the assembly of the hybrid thin films. The LbL assembly of ITO nanoparticles was realized on several substrates, including cellulose fibers, write-on transparencies, silicon wafers, quartz crystals, and glasses. By coating the cellulose fibers with ITO nanoparticles, a new type of conductive paper was manufactured. By LbL assembly of ITO on write-on transparencies, transparent conductive thin films with conductivity of 10⁻⁴ S/cm and transparency of over 80 % in the visible range were also prepared. As a result of this work on the mechanisms and applications of LbL grown films, the understanding of the LbL assembly of polyelectrolytes and inorganic nanoparticles was significantly extended. In addition to working with ITO nanoparticles, this thesis also demonstrated the ability to grow bicomponent [PEI/SiO₂]n thin films. It was further demonstrated that under the right pH conditions, these films can be grown exponentially (e-LbL), resulting in much thicker films, consisting of mostly the inorganic nanoparticles, in much fewer assembly steps than traditional linearly grown films (l-LbL). These results open the door to new research opportunities for achieving structured nanoparticle thin films, whose functionality depends primarily on the properties of the nanoparticles.