No description available.

The results described in this dissertation focus on the synthesis and utilization of several disulfonated poly(arylene ether) random copolymer membranes in fuel cell and reverse osmosis applications. Poly(arylene ether)s were prepared by direct step copolymerization using a third monomer 3,3–-disulfonated 4,4–-dichlorodiphenylsulfone. The membrane properties of a 4,4–-biphenol-based disulfonated poly (arylene ether sulfone) random copolymer (BPS-35), optionally blended with various fluorine containing polymers or unsulfonated biphenol-based poly (arylene ether sulfone)s (Radel R) were investigated for fuel cell applications. Fluorine containing copolymers used included with 2,2–-hexafluoroisopropylidene 4,4–-biphenol based unsulfonated (6F-00) or disulfonated (6FS-35 and 6FS-60) PAES, hexafluoroisopropylidene biphenol based 4,4–-difluoro phenyl phosphine oxide) (6FPPO), and poly(vinylidene fluoride) (Kynar®). Tapping mode atomic force microscopy (TM-AFM) images of the membranes with 10 wt% of fluorinated copolymers showed macroscopic phase separation. Good miscibility between the copolymers at low concentrations was also confirmed by the observation of only one glass transition temperature. Compared to the benchmark Nafion 1135, the 10wt% blends of the fluorinated copolymers afforded a considerable reduction in the methanol permeabilities, which is important for direct methanol fuel cells (DMFC). The best DMFC performance with 0.5 M methanol fuel was illustrated with blends containing 10 wt% 6FS-00. At higher methanol concentrations (up to 2.0 M) BPS-35/6FS-00 (90/10) membranes outperformed both Nafion membranes. Blends of BPS-35 blends with 6FS-35 or Radel R were also used as RO membranes. The highest salt rejections of 97.2 and 98.0% were obtained from BPS35/Radel R (90:10) and BPS-35/6FS-35 (95:5) blends, respectively in the salt form. A systematic study of the preparation of BPS-20 random copolymer skin-core asymmetric membranes by diffusion induced phase separation (DIPS) from various polar aprotic solvent or cosolvent systems is reported. The best aprotic solvents to generate an asymmetric structure were NMP and DMAc whereas tetrahydrofuran (THF)/ formamide (FAm) (80/20 v/v) mixtures proved to be the best co-solvent systems. Acetone was the best non-solvent to prepare asymmetric membranes from both aprotic solvents and co-solvent mixtures. Overall, asymmetric membranes prepared from THF/FAm co-solvent mixtures illustrated the most stable phase separated morphology that was free of macrovoids. However, thicker skins (~5 μM) were formed due to the high volatility of THF. Therefore, ultra-thin skin thin film composites (TFC) based on BPS-20 in diethylene glycol (Di(EG) were prepared. Thermal treatment of these TFC was conducted at 90 °C and the addition of 20 wt% glycerin to the casting formulation helped to prevent pore collapse in the porous Udel polysulfone. A minimum of three coats was required to obtain a dense, smooth, and pinhole free skin layer. The generation of three dimensional (ternary) solubility parameter phase diagrams based on experimental data was formulated and a region of solubility based on the solubility parameters of the aprotic solvents and the different co-solvent systems was established for BPS-20. / Ph. D.

Due to their outstanding properties, poly(arylene ethers) are useful as toughness modifiers in epoxy resins (EP). Furthermore, these polymers show rather low intrinsic fire risks. According to recent research it has been incorporated that poly(arylene ether phosphine oxides) [PAEPO’s] can further improve the fire behavior. Increasing phosphorous content of the PAEPO can influence the fire behavior too. Fire retardants containing phosphorus – regardless of whether an additive or reactive approach is used – show different mechanisms in the condensed and gas phase. In the present study PSU Control (BPA based polysulfone) with four different PAEPO’s and their corresponding blends with an EP were investigated. All poly(arylene ether phosphine oxides) were synthesized by nucleophilic aromatic polycondensation. The polymers obtained covered a wide range of weight average molar masses (6,000 – 150,000 g/mol) as determined by size exclusion chromatography with multi-angle light scattering detection (MALLS). FTIR, NMR spectroscopy and MALDI-TOF revealed formation of the desired polymer structure of the linear poly(arylene ethers). All polymers were easily soluble in common organic solvents, thus enabling processing from solution.The pyrolysis and the fire retardancy mechanisms of the polymers and blends with epoxy resin (EP) were tackled by means of a comprehensive thermal analysis (thermogravimetry (TG), TG-evolved gas analysis) and fire tests [PCFC, limiting oxygen index (LOI), UL-94, cone calorimeter]. The Mitsunobu reaction of Dimethyl-5-hydroxyisophthalate and a long chain semifluorinated alcohol requires triphenyl phosphine as a reactant. Identical, in some case higher yield was obtained in the usual conditions, with triphenyl phosphine and with trivalent phosphorus containing polymers, which was prepared in solvent free bulk (melt) polymerization technique from trivalent phosphorus monomer and a silylated diphenol in presence of CsF. Purification and the recovery of the final product which is always a big challenge in case of Mitsunobu reaction, was far more easier using polymer compared to triphenyl phosphine. During polymerization there was a possibility to have polymer having repeating unit containing both trivalent phosphorus and phosphine oxide. The trivalent phosphorus content of the polymer can be varied using different molar concentration of CsF.

Monolithische Phasen werden seit ca. 20 Jahren entwickelt und sind in den letzten Jahren eine attraktive Alternative zu etablierten mit Partikeln gefüllten Säulen geworden. Sie werden in anorganische Phasen und organische Polymermonolithe unterteilt. Monolithe bestehen aus einem einzigen, durchgehenden Stück. Charakteristisch ist das sie durchziehende Porennetzwerk, durch das der Eluent mit geringerem hydraulischen Widerstand fließen kann und das somit schnellere Flussraten ermöglicht. Polymermonolithe werden vorwiegend für die Separation großer Biomoleküle aufgrund eines durch Konvektion beschleunigten Massentransfers eingesetzt. Zudem sind sie über einen breiten pH-Wert-Bereich stabil und können direkt (in situ) im gewünschten Format polymerisiert werden. In der vorliegenden Arbeit gelang die Herstellung neuartiger epoxidbasierter Phasen nach einem von Weller et al. entwickelten Konzept, die im Affinitätsexperiment angewendet wurden. Die Herstellung erfolgte durch Autopolymerisation polyfunktioneller Glycidylether. Für die Funktionalisierung wurden nicht polymerisierte Epoxide genutzt. Als Monomere dienten TEPIC, GE 100 sowie GE 500. Die Arbeiten konzentrierten sich vor allem auf die bei Raumtemperatur durchführbaren Synthesen mit dem höher funktionellen GE 500. Die Polymerisationsbedingungen wurden hinsichtlich Porogenmischung und -anteil optimiert. Eine mit 75 Vol.-% Porogen (Dioxan/ MTBE (2:3)) hergestellte und mit rProtein A funktionalisierte Kapillarsäule (66 %, 12 µm, 7m2/g) ergab im Affinitätsexperiment eine Kapazität von 0,44 mg/mL aus Kaninchenserum isolierbarem IgG. Durch Beimischung von 60 % BDE konnte der Epoxidgehalt vervierfacht und die Porengröße auf 400 nm bei 59 % Porosität reduziert werden. Die spezifische Oberfläche wurde verdreifacht und die Kapazität präparierter Disks auf 0,90 mg/mL etwa verdoppelt. Die in dieser Arbeit entwickelten Disks können zur Isolierung von IgG aus einer komplexen Probe, wie beispielsweise Blutserum, eingesetzt werden. / Monolithic supports have been developed since 20 years and have become an attractive alternative to well-established columns packed with particles over the past years. They are classified into inorganic media and organic polymer monoliths. Monoliths consist of a single, continuous piece with an integrated characteristic porous network through which the eluent can flow with lower hydraulic resistance and which consequently offers higher flow rates. Due to an accelerated mass transfer caused by convection polymer monoliths are mainly used for separation of large biomolecules. In addition, they are stable over a wide pH range and can be polymerized directly (in situ) in the desired format. In the present work the successful preparation of new epoxide-based supports according to a concept introduced by Weller et al. as well as their application in affinity chromatography are reported. Their preparation was carried out by self-polymerization of polyfunctional glycidyl ethers and for functionalization non-polymerized epoxide groups were used. As monomers TEPIC, GE 100 and GE 500 were utilized. The work has focused especially on the polymerization of the higher functional GE 500, which can be perfomed at room temperature and was optimized in terms of both composition and amount of porogen. The extraction of IgG from rabbit serum with a capillary column (66 %, 12 µm, 7m2/g) prepared by 75 vol.-% porogen (dioxane/ MTBE (2:3)) and functionalized with rprotein A resulted in a capacity of 0,44 mg/mL. By addition of 60 % BDE the epoxide content was quadrupled and the pore size reduced to 400 nm while maintaining consistently high porosity of 59 %. The specific surface area was tripled and the capacity of prepared disks approximately doubled to 0,90 mg/mL. The disks developed in this work can be applied for the isolation of IgG from complex samples such as serum.

Cette thèse se propose d’étudier les façons dont la pensée et l’imaginaire grec de l’époque archaïque se représentaient quelques pans du réel qui ne se laissaient jamais voir ni atteindre: l’éther, l’air et l’abîme marin. Vu le caractère insondable de ces espaces, l’imagination et l’abstraction se sont ingéniées à les appréhender par un discours spécifique et à les intégrer dans le système de connaissances et de croyances propre à l’époque en leur assignant une place dans le système de l’univers, en les rattachant à une hiérarchie de l’ordre cosmologique, en leur donnant une forme, en classant leurs objets et en les rapportant aux modèles du monde connu, en les aménageant par les moyens les plus divers. Une étude des formes d’expression de la pensée grecque archaïque, autant littéraires qu’iconographiques, permet de cerner les diverses formes de représentation des domaines inaccessibles et les modèles d’organisation spatiale issus de ce type de pensée. Grâce à la dialectique particulière qui ressort du rapport entre espace et mouvement, cette thèse se propose également d’interroger le corpus des sources grecques archaïques sous des angles jusqu’ici peu explorés: comment maîtrise-t-on l’espace par les déplacements physiques en dehors des parcours terrestres? Comment les schémas du mouvement dans l’espace se sont-ils forgés? Comment les dichotomies issues de la logique spatiale archaïque (haut/bas, droite/gauche, est/ouest, en deça/au-delà, etc.) influent-elles sur la structuration spatiale? Quelles espèces d’espace révèlent les déplacements à travers les différents niveaux du monde, que ce soit ceux des dieux, ceux des mortels et d’autres entités, forces physiques et substances privilégiées dans le commerce avec le divin et le monde d’en haut? Ces analyses mettent en valeur les façons dont l’imagination et l’abstraction plutôt que l’expérience vécue ont contribué, à leur façon, à structurer l’espace et à forger l’image du monde comme κόσμος, monde mis en ordre et soumis autant aux lois physiques qu’aux lois divines. / The present dissertation aims to study the ways in which archaic Greek thought symbolically came to grips with three elements of physical reality, which can never be thoroughly accessed by humans: the ether, the air, and the marine abyss. Due to the rather fathomless character of the different spaces underlying these elements, human imagination and abstract thought endeavored to apprehend them through a specific discourse and system of knowledge and beliefs. Both this discourse and its inherent epistemological system were specific to the abovementioned historical period. They assigned the spaces in question a place in the universe via a hierarchy of the cosmological order. Thus, these spaces acquired a definite shape, while their contents have been classified and connected with patterns of the known world, while being combined in multifarious ways. In my doctoral work, I argue that it is possible to define the various forms of representations of such inaccessible domains of being, together with the patterns of their spatial organization, by paying close attention to the manner in which the archaic Greek thought expressed itself through literature and iconography. Drawing on the particular dialectic that pertains to the relation between space and movement, this thesis wishes to analyze the corpus of ancient Greek sources from multiple vantages which so far have been only vaguely explored. To exemplify, I shall tackle the way, in which space is understood in view of journeys other than terrestrial. I also discuss how certain paradigms of movement in space have emerged in this regard. Another question I shall answer concerns the manner, in which certain dichotomies of archaic logic related to space (up/down, right/left, east/west, within/beyond, etc.) have influenced the structuring of space. With that in mind, I expand upon the issue of the types of spatiality revealed through the journeys across the different levels of the world, namely the journeys of the gods, mortals, and other forces involved in the human interaction with the divine and any other superior region. These analyses will jointly show that the philosophical structuring of space and the emergence of an image of the world understood as κόσμος – i.e., as a world ordered by and obeying both physical and divine laws – are the result of imagination and abstract reflective efforts rather than subjective experience.

Álcoois primários sulfatados de cadeia longa, usualmente na forma de sais de sódio, são tensoativos de grande interesse comercial utilizados em diversas formulações de higiene pessoal e limpeza doméstica. Eles são produzidos comercialmente através da reação de álcoois etoxilados com trióxido de enxofre seguida de imediata neutralização com hidróxido de sódio. O produto formado é uma solução neutra de álcool primário etoxilado sulfatado em água. Sabe-se que a armazenagem desse produto por longos períodos de tempo em temperaturas elevadas pode levar à hidrólise completa, mas, em condições normais de uso e temperatura ambiente é esperado que o produto seja resistente à hidrólise. No entanto observou-se que algumas amostras comerciais de lauril éter sulfato de sódio que foram estocadas por diferentes períodos de tempo em frascos fechados à temperatura ambiente sofreram hidrólise em intervalos de tempo relativamente curtos. Isso leva à hipótese de que o comportamento de hidrólise seria influenciado por outras variáveis além da temperatura e do tempo de estocagem. O presente trabalho consistiu em identificar as variáveis de maior impacto na reação de hidrólise por meio de experimentos planejados. O teor de ativos foi acompanhado ao longo da reação para avaliar o efeito da presença de eletrólitos, de material insulfatado, em diferentes temperaturas, variando-se o pH inicial por meio da adição de ácido clorídrico. O comportamento da reação de hidrólise observado foi compatível com aquele descrito na literatura para o dodecil sulfato de sódio. A hidrólise apresentou-se como sendo autocatalítica, com a aceleração da taxa de reação provavelmente causada pela presença de íons hidrogênio liberados na reação. Foi possível identificar que as variáveis de maior efeito na reação foram: pH inicial, o teor de cloreto de sódio e a temperatura. O modelo de troca iônica em pseudo-fase foi utilizado para o tratamento dos resultados experimentais e mostrou-se adequado tendo sido, portanto, utilizado para prever o comportamento de estabilidade do produto à temperatura ambiente e nas condições em que o produto é normalmente comercializado. Um modelo empírico de redes neurais foi desenvolvido com sucesso para prever o comportamento do pH ao longo do tempo para as condições estudadas. / Long-chain primary alkyl sulfuric acids, usually as their sodium salts, are important commercial surfactants used in a large number of household and personal care formulations. They are commercially produced by treatment of mixtures of ethoxylated fatty alcohols with sulfur trioxide followed by immediate neutralization with sodium hydroxide, a neutral aqueous mixture of sodium primary alkyl ether sulfate is obtained. It is known that prolonged storage of the material at elevated temperature can lead to complete hydrolysis but under normal use and typical environmental conditions the product is expected to be resistant to hydrolysis. In spite of that it has been observed that some commercial samples of sodium lauryl ether sulfate stored for different periods of time in sealed containers at room temperature have undergone hydrolysis in a relatively short period of time which leads to the hypothesis that the hydrolysis behavior would be strongly influenced by variables other than temperature and storage time. The present work consisted of identifying the process variables with the most significant effect on the acid hydrolysis by using experimental design. The rate of hydrolysis has been followed acidimetrically to evaluate the effect of electrolytes as well as the concentration of unsulfated matter at different temperatures, over a wide initial pH range, under the presence of added hydrochloric acid. The pattern of kinetic behaviour observed was broadly the same as previously described for the sodium dodecyl sulfate. The hydrolysis presented the characteristic autocatalytic form, the catalysis presumably arising from the production of hydrogen sulfate ions. It was possible to observe that the most significant effects on the rate of hydrolysis were the initial pH, the total amount of sodium chloride and the temperature. The results were also discussed in terms of the ion-exchange pseudophase model of the micelle reaction. Accordingly to the fitting of parameters that was carried out it is possible to conclude that the pseudo-phase ion-exchange theory is found to account satisfactorily for the results reported and it was used to predict the stability behavior of the product at room temperature and under normal commercial conditions. A neural network based model was also successfully developed in order to predict the pH behavior in the conditions studied.

Die vorliegende Untersuchung wurde am International Livestock Centre for Africa (ILCA), jetzt International Livestock Research Institute (ILRI) auf der Versuchsstation Debre Birhan in Äthiopien durchgeführt. Diese Untersuchung ist Teil eines panafrikanischen ILRI-Forschungsprogramms zur Untersuchung und Charakterisierung einheimischer kleiner Wiederkäuer im Sub-Saharischen Afrika auf genetische Resistenz gegenüber Endoparasiten. Das Ziel dieser Arbeit bestand darin, Ergebnisse zu verschaffen, die zum Verständnis der relativen Leistung zweier äthiopischer Hochlandschafrassen (Horroschaf und Menzschaf) unter Stationsbedingungen dienen sollen. Horro-Lämmer (2,43±0,03 kg) waren signifikant (p / This study has been carried out at the former International Livestock Centre for Africa (ILCA), that is now the International Livestock Research Institute (ILRI) experiment station at Debre Birhan, Ethiopia. This research is part of an ILCA (now ILRI) Pan-African research programme designed to investigate and characterise genetic resistance to endoparasites in some indigenous small ruminants in sub-Saharan Africa. The present study was, therefore, undertaken in an attempt to generate information that may contribute towards the understanding of the relative performance of two highland sheep (Horro and Menz) of Ethiopia under station management conditions. Horro lambs were significantly heavier (P

Cette thèse se propose d’étudier les façons dont la pensée et l’imaginaire grec de l’époque archaïque se représentaient quelques pans du réel qui ne se laissaient jamais voir ni atteindre: l’éther, l’air et l’abîme marin. Vu le caractère insondable de ces espaces, l’imagination et l’abstraction se sont ingéniées à les appréhender par un discours spécifique et à les intégrer dans le système de connaissances et de croyances propre à l’époque en leur assignant une place dans le système de l’univers, en les rattachant à une hiérarchie de l’ordre cosmologique, en leur donnant une forme, en classant leurs objets et en les rapportant aux modèles du monde connu, en les aménageant par les moyens les plus divers. Une étude des formes d’expression de la pensée grecque archaïque, autant littéraires qu’iconographiques, permet de cerner les diverses formes de représentation des domaines inaccessibles et les modèles d’organisation spatiale issus de ce type de pensée. Grâce à la dialectique particulière qui ressort du rapport entre espace et mouvement, cette thèse se propose également d’interroger le corpus des sources grecques archaïques sous des angles jusqu’ici peu explorés: comment maîtrise-t-on l’espace par les déplacements physiques en dehors des parcours terrestres? Comment les schémas du mouvement dans l’espace se sont-ils forgés? Comment les dichotomies issues de la logique spatiale archaïque (haut/bas, droite/gauche, est/ouest, en deça/au-delà, etc.) influent-elles sur la structuration spatiale? Quelles espèces d’espace révèlent les déplacements à travers les différents niveaux du monde, que ce soit ceux des dieux, ceux des mortels et d’autres entités, forces physiques et substances privilégiées dans le commerce avec le divin et le monde d’en haut? Ces analyses mettent en valeur les façons dont l’imagination et l’abstraction plutôt que l’expérience vécue ont contribué, à leur façon, à structurer l’espace et à forger l’image du monde comme κόσμος, monde mis en ordre et soumis autant aux lois physiques qu’aux lois divines. / The present dissertation aims to study the ways in which archaic Greek thought symbolically came to grips with three elements of physical reality, which can never be thoroughly accessed by humans: the ether, the air, and the marine abyss. Due to the rather fathomless character of the different spaces underlying these elements, human imagination and abstract thought endeavored to apprehend them through a specific discourse and system of knowledge and beliefs. Both this discourse and its inherent epistemological system were specific to the abovementioned historical period. They assigned the spaces in question a place in the universe via a hierarchy of the cosmological order. Thus, these spaces acquired a definite shape, while their contents have been classified and connected with patterns of the known world, while being combined in multifarious ways. In my doctoral work, I argue that it is possible to define the various forms of representations of such inaccessible domains of being, together with the patterns of their spatial organization, by paying close attention to the manner in which the archaic Greek thought expressed itself through literature and iconography. Drawing on the particular dialectic that pertains to the relation between space and movement, this thesis wishes to analyze the corpus of ancient Greek sources from multiple vantages which so far have been only vaguely explored. To exemplify, I shall tackle the way, in which space is understood in view of journeys other than terrestrial. I also discuss how certain paradigms of movement in space have emerged in this regard. Another question I shall answer concerns the manner, in which certain dichotomies of archaic logic related to space (up/down, right/left, east/west, within/beyond, etc.) have influenced the structuring of space. With that in mind, I expand upon the issue of the types of spatiality revealed through the journeys across the different levels of the world, namely the journeys of the gods, mortals, and other forces involved in the human interaction with the divine and any other superior region. These analyses will jointly show that the philosophical structuring of space and the emergence of an image of the world understood as κόσμος – i.e., as a world ordered by and obeying both physical and divine laws – are the result of imagination and abstract reflective efforts rather than subjective experience.

Η υπέρταση είναι ένας από τους σημαντικότερους παράγοντες που αυξάνει τα καρδιαγγειακά επεισόδια τα οποία ευθύνονται περίπου για το ήμισυ των θανατηφόρων επεισοδίων στους ενήλικους. To σύστημα ρενίνης-αγγειοτασίνης-αλδοστερόνης (ΣΡΑΑ) διαδραματίζει καθοριστικό ρόλο στην παθοφυσιολογία των καρδιαγγειακών νόσων. Η αναστολή του ΣΡΑΑ σε παθολογικές καταστάσεις μπορεί να πραγματοποιηθεί με αναστολή του ενζύμου της ρενίνης ή παρεμπόδιση της σύνδεσης της ΑΙΙ με τους υποδοχείς ΑΤ1. Έχει διατυπωθεί η υπόθεση ότι τα αμφοτερικά μόρια για να αλληλεπιδράσουν με τον υποδοχέα θα πρέπει πρώτα να εισδύσουν σε κατάλληλη τοπογραφική θέση στις βιολογικές μεμβράνες και μετά με διάχυση να προσεγγίσουν το ενεργό κέντρο όπου όταν προσδεθούν με μία σειρά αντιδράσεων θα εξασκήσουν τη βιολογική τους δράση. Για την κατανόηση του ρόλου των μεμβρανών στο σύστημα ΣΡΑΑ μελετήθηκαν οι αλληλεπιδράσεις της αλισκιρένης (αναστολέας ρενίνης) και ολμεσαρτάνης (ανταγωνιστής αγγειοτασίνης ΙΙ) σε μοντέλα διπλοστιβάδων διπαλμιτικής φωσφατιδυλοχολίνης με ή χωρίς χοληστερόλη. Οι μελέτες διεξήχθησαν κάνοντας χρήση Πυρηνικού Μαγνητικού Συντονισμού (υγρής και στερεής κατάστασης), Διαφορικής Θερμιδομετρίας Σάρωσης, Φασματοσκοπίας Raman και Περίθλασης Ακτίνων-Χ. Σύγκριση των πειραματικών αποτελεσμάτων με άλλες σαρτάνες που μελετήθηκαν κάνοντας χρήση τις ίδιες τεχνικές απόδειξαν ότι όλα τα φάρμακα του ΣΡΑΑ εντοπίζονται στην ενδιάμεση φάση όπου εξασκούν διαφορετικές υδρόφιλες και λιπόφιλες αλληλεπιδράσεις. Επομένως το κάθε φάρμακο αποτυπώνει τη δική του σφραγίδα μέσα στις λιπιδικές διπλοστιβάδες. Αυτή η μοναδικότητα στις αλληλεπιδράσεις κάθε φαρμάκου με τις λιπιδικές διπλοστιβάδες ίσως να σχετίζεται και με τη μοναδικότητα του στο φαρμακευτικό του προφίλ. Ένα άλλο ενδιαφέρον αποτέλεσμα που προέκυψε από τις μελέτες είναι ότι η ολμεσαρτάνη σε μεθανολικό διάλυμα τόσο σε χαμηλή θερμοκρασία όσο και σε θερμοκρασία δωματίου δεν είναι σταθερή και μετατρέπεται στο αιθερικό της παράγωγο το οποίο ταυτοποιήθηκε φασματοσκοπικά. Στις ίδιες συνθήκες δεν παρατηρήθηκε εστεροποίηση. / Hypertension is one of the major risk factors responsible for the increase of half of the cardiovascular episodes in the adults. The system of Renin-Angiotensin-Aldosterone (RAAS) plays a determinative role in the pathophysiology of cardiovascular diseases. In a pathological state the aim is to block the generation of Angiotensin II through inhibition of rennin or angiotensin converting enzymes or its action on AT1 receptor. It has been hypothesized that amphiphilic molecules in order to exert their action on the receptor site, they have first to enter into the lipidic core of the lipid bilayers and then diffuse towards the active site. Thus, if this mechanism is applied, the lipidic part of the membrane bilayers appears to play an important role in the membrane action. To comprehend on the membrane:drug interactions we have studied the effects of olmesartan and aliskiren using dipalmitoylphosphatidylcholine bilayers with or without cholesterol. Various physical chemical methodologies such as liquid and solid state NMR , x-ray diffraction, Raman spectroscopy and Differential Scanning Calorimetry have been applied. The comparative results with other SARTANs showed that all drugs of the RAAS system act on the polar group and upper part of the alkyl chain, but exert different interactions. Thus, each drug is characterized by its own fingerprint in terms of its interactions and this may explain its unique pharmacological profile. Another, intriguing result derived from this thesis dissertation is the observation that olmesartan in methanolic solution is converted to its ether analogue. This isolated product was unambiguously structurally elucidated using a combination of LC-MS and 2D NMR spectroscopy.

Álcoois primários sulfatados de cadeia longa, usualmente na forma de sais de sódio, são tensoativos de grande interesse comercial utilizados em diversas formulações de higiene pessoal e limpeza doméstica. Eles são produzidos comercialmente através da reação de álcoois etoxilados com trióxido de enxofre seguida de imediata neutralização com hidróxido de sódio. O produto formado é uma solução neutra de álcool primário etoxilado sulfatado em água. Sabe-se que a armazenagem desse produto por longos períodos de tempo em temperaturas elevadas pode levar à hidrólise completa, mas, em condições normais de uso e temperatura ambiente é esperado que o produto seja resistente à hidrólise. No entanto observou-se que algumas amostras comerciais de lauril éter sulfato de sódio que foram estocadas por diferentes períodos de tempo em frascos fechados à temperatura ambiente sofreram hidrólise em intervalos de tempo relativamente curtos. Isso leva à hipótese de que o comportamento de hidrólise seria influenciado por outras variáveis além da temperatura e do tempo de estocagem. O presente trabalho consistiu em identificar as variáveis de maior impacto na reação de hidrólise por meio de experimentos planejados. O teor de ativos foi acompanhado ao longo da reação para avaliar o efeito da presença de eletrólitos, de material insulfatado, em diferentes temperaturas, variando-se o pH inicial por meio da adição de ácido clorídrico. O comportamento da reação de hidrólise observado foi compatível com aquele descrito na literatura para o dodecil sulfato de sódio. A hidrólise apresentou-se como sendo autocatalítica, com a aceleração da taxa de reação provavelmente causada pela presença de íons hidrogênio liberados na reação. Foi possível identificar que as variáveis de maior efeito na reação foram: pH inicial, o teor de cloreto de sódio e a temperatura. O modelo de troca iônica em pseudo-fase foi utilizado para o tratamento dos resultados experimentais e mostrou-se adequado tendo sido, portanto, utilizado para prever o comportamento de estabilidade do produto à temperatura ambiente e nas condições em que o produto é normalmente comercializado. Um modelo empírico de redes neurais foi desenvolvido com sucesso para prever o comportamento do pH ao longo do tempo para as condições estudadas. / Long-chain primary alkyl sulfuric acids, usually as their sodium salts, are important commercial surfactants used in a large number of household and personal care formulations. They are commercially produced by treatment of mixtures of ethoxylated fatty alcohols with sulfur trioxide followed by immediate neutralization with sodium hydroxide, a neutral aqueous mixture of sodium primary alkyl ether sulfate is obtained. It is known that prolonged storage of the material at elevated temperature can lead to complete hydrolysis but under normal use and typical environmental conditions the product is expected to be resistant to hydrolysis. In spite of that it has been observed that some commercial samples of sodium lauryl ether sulfate stored for different periods of time in sealed containers at room temperature have undergone hydrolysis in a relatively short period of time which leads to the hypothesis that the hydrolysis behavior would be strongly influenced by variables other than temperature and storage time. The present work consisted of identifying the process variables with the most significant effect on the acid hydrolysis by using experimental design. The rate of hydrolysis has been followed acidimetrically to evaluate the effect of electrolytes as well as the concentration of unsulfated matter at different temperatures, over a wide initial pH range, under the presence of added hydrochloric acid. The pattern of kinetic behaviour observed was broadly the same as previously described for the sodium dodecyl sulfate. The hydrolysis presented the characteristic autocatalytic form, the catalysis presumably arising from the production of hydrogen sulfate ions. It was possible to observe that the most significant effects on the rate of hydrolysis were the initial pH, the total amount of sodium chloride and the temperature. The results were also discussed in terms of the ion-exchange pseudophase model of the micelle reaction. Accordingly to the fitting of parameters that was carried out it is possible to conclude that the pseudo-phase ion-exchange theory is found to account satisfactorily for the results reported and it was used to predict the stability behavior of the product at room temperature and under normal commercial conditions. A neural network based model was also successfully developed in order to predict the pH behavior in the conditions studied.