Wireless operation, near-field or far-field, is a core functionality of any mobile or autonomous system. These systems are battery operated or most often utilize energy scavenging as a means of power generation. Limited access to power, expected long and uninterrupted operation, and constrained physical parameters (e.g. weight and size), which limit overall power harvesting capabilities, are factors that outline the importance for innovative low-power approaches and designs in advanced low-power wireless applications. Low-power approaches become especially important for the wireless transceiver, the block in charge of wireless/remote functionality of the system, as this block is usually the most power hungry component in an integrated system-on-chip (SoC). Three such advanced applications with stringent power requirements are examined including space-based exploratory remote sensing probes and their associated radiation effects, millimeter-wave phased-array radar for high-altitude tactical and geological imaging, and implantable biomedical devices (IMDs), leading to the proposal and implementation of low-power wireless solutions for these applications in SiGe BiCMOS and CMOS and platforms.

Avec l'ouverture de la bande 57-66 GHz en Europe, de nouvelles technologies de communication sans fil à haut débit sont en cours de développement. De nombreux avantages liés à cette bande de fréquence ont notamment conduit à envisager la transposition du principe de l'identification par radiofréquence (RFID) en bande millimétrique : la MMID. Les réglementations internationales font notamment apparaître une bande passante commune de 5 GHz qui permettrait la mise en place de solutions universelles. De plus la sécurisation des communications point-à-point et la directivité des réseaux d'antennes offrent des perspectives intéressantes.Les travaux présentés dans cette thèse visent à contribuer au développement de la MMID. Ils soulignent les principaux verrous de cette technologie et présentent les différentes solutions proposées qui couvrent de multiples aspects : conception d'antennes et de réseaux d'antennes, conception de prototypes de tags MMID passifs, caractérisation et méthodologie de mesure dont la conception intégrale d'un banc de mesure en bande V, amélioration des performances des tags, et étude de fonctionnalités de capteur intégrées aux tags. Les différents prototypes de tags MMID fabriqués ont permis de réaliser des communications passives de type rétro-modulation jusqu'à 20 cm. De plus, des fonctions de capteur d'humidité et capteur de pression intégrées aux tags MMID ont été montrées expérimentalement. L'ensemble de ces résultats ouvre la voie à de nouvelles perspectives pour les domaines des télécommunications et des réseaux de capteurs en bande millimétrique. / With the opening of the 57-66 GHz band in Europe, new high data-rate wireless communication technologies are currently under development. Numerous advantages linked to the frequency band conducted to consider the transposition of the radiofrequency identificaion (RFID) principle to the millimeter frequency band: the MMID. The international regulations provide a common bandwidth of 5 GHz allowing universal solutions. Moreover, the communication security of point-to-point networks and the directivities of the antennas present interesting perspectives.The presented work in this thesis looks for contributing to the development of MMID. The work underlines the principal locks of this technology and it presents the different proposed solutions covering multiple aspects: conception of antennas and antennas arrays, conception of MMID tags prototypes, characterization and measurement methodology including the complete conception of a measurement bench in V-band, improvement of the tags performances and study of sensing functionalities integrated in the tags. Different prototypes of MMID tags are fabricated and passive communications based on the backscattering of the tags were demonstrated up to 20 cm. In addition, humidity and pressure sensing functionalities were proved by experimentations. The overall of these results pave the way for new perspectives for the wireless communication domain and sensors networks in the millimeter-wave band.

The radio frequency (RF) spectrum as a natural resource is severely under-utilized over time and space due to an inefficient licensing framework. As a result, in-creasing cellular and wireless network usage is placing significant demands on the licensed spectrum. This has led to the development of cognitive radios, software defined radios and mm-wave radios. Cognitive radios (CRs) enable more efficient spectrum usage over a wide range of frequencies and hence have emerged as an effective solution to handle huge network demands. They promise versatility, flex-ability and cognition which can revolutionize communications systems. However, they present greater challenges to the design of radio frequency (RF) front-ends. Instead of a narrow-band front-end optimized and tuned to the carrier frequency of interest, cognitive radios demand front-ends which are versatile, configurable, tun-able and capable of transmitting and receiving signals with different bandwidths and modulation schemes. The primary purpose of this thesis is to design a re-configurable, wide-band and low phase-noise fast settling frequency synthesizer for cognitive radio applications. Along with frequency generation, an area efficient multi-band low noise amplifier (LNA) with integrated built-in-self-test (BIST) and a strong immunity to interferers has also been proposed and implemented for these radios. This designed LNA relaxes the specification of harmonic content in the synthesizer output. Finally some preliminary work has also been done for mm-wave (V-band) frequency synthesis. The Key Contributions of this thesis are: A frequency synthesizer, based on a type-2, third-order Phase Locked Loop (PLL), covering a frequency range of 0.1-5.4 GHz, is implemented using a 0.13 µm CMOS technology. The PLL uses three voltage controlled oscillators (VCOs) to cover the whole range. It is capable of switching between any two frequencies in less than 3 µs and has phase noise values, compatible with most communication standards. The settling of the PLL in the desired state is achieved in dynamic multiple steps rather than traditional single step settling. This along with other circuit techniques like a DAC-based discriminator aided charge pump, fast acquisition pulse-clocked based PFD and timing synchro-negation is used to obtain a significantly reduced settling time A single voltage controlled LC-oscillator (LC-VCO) has been designed to cover a wide range of frequencies (2.0-4.1 GHz) using an area efficient and switch-able multi-tap inductor and a capacitor bank. The switching of the multi-tap inductor is done in the most optimal manner so as to get good phase-noise at the output. The multi-tap inductor provides a significant area advantage, and in spite of a degraded Q, provides an acceptable phase noise of -123 dBc/Hz and -113 dBc/Hz at an offset of 1 MHz at carrier frequencies of 2 and 4 GHz, respectively. Implemented in a 0.13 µm CMOS technology, the oscillator with ≈ 69 % tuning range, occupies an active area of only 0.095 mm2. An active inductor based noise-filter has been proposed to improve the phase-noise performance of the oscillator without much increase in the area. A variable gain multi-band low noise amplifier (LNA) is designed to operate over a wide range of frequencies (0.8 GHz to 2.4 GHz) using an area efficient switchable-π network. The LNA can be tuned to different gain and linearity combinations for different band settings. Depending upon the location of the interferers, a specific band can be selected to provide optimum gain and the best signal-to-intermodulation ratio. This is accomplished by the use of an on-chip Built-in-Self-Test (BIST) circuit. The maximum power gain of the amplifier is 19 dB with a return loss better than 10 dB for 7 mW of power consumption. The noise figure is 3.2 dB at 1 GHz and its third-order intercept point (I I P3) ranges from -15 dBm to 0 dBm. Implemented in a 0.13 µm CMOS technology, the LNA occupies an active area of about 0.29 mm2. Three different types of VCOs (stand-alone LC VCO, push-push VCO and a ring oscillator based VCO) for generating mm-wave frequencies have been implemented using 65-nm CMOS technology and their measured results have been analyzed

This thesis deals with optical synthesis of unmodulated and modulated microwave signals. Generation of microwave signals based on optical heterodyning is discussed in detail. The effect of phase noise of laser on heterodyned output has been studied for different phase noise profiles. Towards this, we propose a generic algorithm to numerically model the linewidth broadening of a laser due to phase noise. Generation of microwave signals is demonstrated practically by conducting an optical heterodyning experiment. Signals ranging in frequency from 12.5 MHz to 27 GHz have been generated. Limitations of optical heterodyning based approach in terms of phase noise performance and frequency stability are discussed and practically demonstrated. A hardware-efficient Optical Phase Locked Loop (OPLL) is proposed to overcome these issues. Phase noise tracking performance of the proposed OPLL has been experimentally demonstrated. Phase noise values as low as -105 dBc/Hz at 10 KHz offset have been achieved. Optical modulators, owing to their extremely low electro-optic response time, can support high frequency modulating signals. This makes them highly attractive in comparison to their microwave counterparts. In this thesis, we propose techniques to generate microwave signals modulated at very high bit rates by down-converting the corresponding modulated optical signals to microwave domain. Down-conversion required for this process is achieved by optical heterodyning. The proposed concept has been theoretically analyzed, simulated and experimentally validated. Amplitude Modulated and ASK modulated microwave signals have been generated as Proof-of-Concept. Limitations posed by OPLL in generation of angle modulated microwave signals by optical heterodyning have been brought out. Schemes overcoming these limitations have been proposed towards generation of BPSK and QPSK modulated microwave signals. Integrated Optics (IO) technology has been studied as a means of implementation of the proposed concepts. IO components like Sinusoidal bends, Y-branch splitters and Electro-Optic-Modulators (EOMs) have been designed towards optical synthesis of modulated microwave signals. Propagation of modulated optical signal through these IO components has also been studied. An all-optic scheme based on Optical Beam Forming is proposed for transmission of QPSK modulated signal. Limitation of phase-shifting based approach, in terms of beam-squint, has been brought out. True-Time-Delay based approach has been proposed for applications demanding wide instantaneous bandwidth to avoid beam-squint. Algorithms / numerical methods required for analyses and simulations associated with the above-mentioned tasks have been evolved. This study is envisaged to provide useful insight into the realization of high-speed, compact, light-weight data transmitting systems based on Integrated Optics for future onboard spacecraft applications. This work, we believe, is a step towards realization of an Integrated Optic System-on-Chip solution for specific microwave data transmission applications.

Ce travail de thèse s’inscrit dans le cadre d’un projet Français « VéLo » qui est une collaboration entre l’industriel STMicroelectronics et plusieurs laboratoires dont les laboratoires IMS-bordeaux et LAAS. Le but du projet est de concevoir un prototype de radar anticollision millimétrique. Dans ce travail un synthétiseur de fréquence est implémenté. Ce dernier sera intégré dans la chaine de réception du démonstrateur. Une étude bibliographique des architectures classiques de système de radiocommunication a été réalisée. Des exemples d’architectures rencontrées dans le domaine millimétrique ont été étudiés.L’objet principal de cette thèse est l’étude des oscillateurs synchronisés par injection ILO. L’objectif est de réaliser un oscillateur verrouillé par injection qui sera piloté par un oscillateur de fréquence plus basse possédant des caractéristiques de stabilité et de bruit meilleures.Dans ce travail de thèse, le mécanisme de verrouillage des oscillateurs par injection a été décrit. Un modèle de synchronisation par injection série, basé sur la théorie de Huntoon Weiss et inspiré du travail de Badets réalisé sur les oscillateurs synchrones verrouillés par injection parallèle, est proposé. La théorie établie a permis d’exprimer la plage de synchronisation en fonction de la topologie utilisée et des composants de la structure. La validité de la théorie a été évaluée par la simulation de la structure. Les résultats présentés montrent une bonne concordance entre la simulation et la théorie et permettent de valider le principe de synchronisation par injection. La faisabilité de l’intégration d’un ILO millimétrique synchronisé par l’harmonique d’un signal de référence de fréquence plus basse a été démontrée expérimentalement. Le synthétiseur de fréquence est réalisé en technologie BiCMOS 130nm pour des applications millimétriques de STMicroelectronics. Ce dernier opère dans une plage de 2GHz autour de la fréquence 82,5GHz. Les performances en bruit du synthétiseur sont satisfaisantes. Le bruit de phase de l’ILO recopie celui du signal injecté. Les équipements de mesures utilisés, le bruit de phase de l’oscillateur atteint des valeurs inférieures à -110dBc/Hz à 1MHz de la porteuse. / This thesis is a part of a French project "VELO". The project is collaboration between STMicroelectronics and several laboratories including IMS-Bordeaux and LAAS laboratories. The aim of this project is to achieve a prototype of millimeter anti-collision radar. In this work a frequency synthesizer is implemented. This circuit will be incorporated in the reception chain of the demonstrator. A bibliographical study of classical architecture was completed. Examples of architectures encountered in the millimeter frequency range have been studied. The purpose of this thesis is to study the phenomena of synchronization in oscillators. The objective is to design an injection locked oscillator ILO driven by another oscillator, the second oscillator operates at lower frequency and offers better stability and noise characteristics.In this thesis, the injection locking mechanism of the oscillators has been described. A model of synchronization by series injection is proposed. The model is based on the theory of Huntoon and Weiss and inspired by Badets’ work performed on parallel injection. The theory expresses the synchronized frequency range depending on the used topology and the values of the components. The validity of the theory was evaluated by simulation. The results show good agreement between simulation and theory and validate the principle of synchronization by injection.The feasibility of a millimeter ILO synchronized by the harmonic of a reference signal operating at lower frequency has been demonstrated experimentally. The synthesizer was implemented in BiCMOS technology for 130nm applications millimeter of STMicroelectronics. The oscillator operates at 82.5 GHz and performs a frequency range of 2GHz. The noise performance of the synthesizer is satisfactory. The phase noise of the ILO depends on the reference phase noise, and reaches values of -110dBc/Hz at 1MHz from the carrier frequency.

A 5 GHz continuous unlicensed bandwidth is available at millimeter-wave (mm-wave) frequencies around 60 GHz and offers the prospect for multi gigabit wireless applications. The inherent atmospheric attenuation at 60 GHz due to oxygen absorption makes the frequency range ideal for short distance communication networks. For these mm-wave wireless networks, the low noise amplifier (LNA) is a critical subsystem determining the receiver performance i.e., the noise figure (NF) and receiver sensitivity. It however proves challenging to realise high performance mm-wave LNAs in a silicon (Si) complementary metal-oxide semiconductor (CMOS) technology. The mm-wave passive devices, specifically on-chip inductors, experience high propagation loss due to the conductivity of the Si substrate at mm-wave frequencies, degrading the performance of the LNA and subsequently the performance of the receiver architecture. The research is aimed at realising a high performance mm-wave LNA in a Si BiCMOS technology. The focal points are firstly, the fundamental understanding of the various forms of losses passive inductors experience and the techniques to address these issues, and secondly, whether the performance of mm-wave passive inductors can be improved by means of geometry optimising. An associated hypothesis is formulated, where the research outcome results in a preferred passive inductor and formulates an optimised passive inductor for mm-wave applications. The performance of the mm-wave inductor is evaluated using the quality factor (Q-factor) as a figure of merit. An increased inductor Q-factor translates to improved LNA input and output matching performance and contributes to the lowering of the LNA NF. The passive inductors are designed and simulated in a 2.5D electromagnetic (EM) simulator. The electrical characteristics of the passive structures are exported to a SPICE netlist which is included in a circuit simulator to evaluate and investigate the LNA performance. Two LNAs are designed and prototyped using the 13μ-m SiGe BiCMOS process from IBM as part of the experimental process to validate the hypothesis. One LNA implements the preferred inductor structures as a benchmark, while the second LNA, identical to the first, replaces one inductor with the optimised inductor. Experimental verification allows complete characterization of the passive inductors and the performance of the LNAs to prove the hypothesis. According to the author's knowledge, the slow-wave coplanar waveguide (S-CPW) achieves a higher Q-factor than microstrip and coplanar waveguide (CPW) transmission lines at mm-wave frequencies implemented for the 130 nm SiGe BiCMOS technology node. In literature, specific S-CPW transmission line geometry parameters have previously been investigated, but this work optimises the signal-to-ground spacing of the S-CPW transmission lines without changing the characteristic impedance of the lines. Optimising the S-CPW transmission line for 60 GHz increases the Q-factor from 38 to 50 in simulation, a 32 % improvement, and from 8 to 10 in measurements. Furthermore, replacing only one inductor in the output matching network of the LNA with the higher Q-factor inductor, improves the input and output matching performance of the LNA, resulting in a 5 dB input and output reflection coefficient improvement. Although a 5 dB improvement in matching performance is obtained, the resultant noise and gain performance show no significant improvement. The single stage LNAs achieve a simulated gain and NF of 13 dB and 5.3 dB respectively, and dissipate 6 mW from the 1.5 V supply. The LNA focused to attain high gain and a low NF, trading off linearity and as a result obtained poor 1 dB compression of -21.7 dBm. The LNA results are not state of the art but are comparable to SiGe BiCMOS LNAs presented in literature, achieving similar gain, NF and power dissipation figures. / Dissertation (MEng)--University of Pretoria, 2012. / Electrical, Electronic and Computer Engineering / unrestricted

Les réseaux mobiles de la cinquième génération (5G) sont conçus pour introduire de nouveaux services nécessitant des débits de données extrêmement hauts et une faible latence. 5G sera un changement de paradigme qui comprend des réseaux hétérogènes densifiés, des réseaux d'accès radio virtualisés, des fréquences porteuses à ondes millimétrées et des densités de périphériques très élevées. Cependant, contrairement aux générations précédentes, 5G sera un réseau holistique, intégrant n'importe quelle nouvelle technologie radio avec les technologies LTE et WiFi existant. Dans ce contexte, on se concentre sur de nouvelles stratégies d'allocation de ressources capables de bénéficier du multihoming dans le cas d'accès double au réseau. On modélise ces algorithmes au niveau du flux et analyse leurs performances en termes de débit, de stabilité du système et d'équité entre différentes catégories d'utilisateurs. On se concentre tout d'abord sur le multihoming dans les réseaux hétérogènes LTE/WiFi. On considère les allocations centrées sur le réseau où un planificateur central effectue des allocations d'équité proportionnelle (PF) locale et globale pour différentes classes d'utilisateurs, utilisateurs individuels (single-homed) et multi-domiciliés (multihomed). Par rapport à un modèle de référence sans multihoming, on montre que les deux stratégies améliorent la performance et la stabilité du système, au détriment d'une plus grande complexité pour la stratégie PF globale. On étudie également les stratégies d'allocation centrées sur l'utilisateur, dans lesquelles les utilisateurs multihomed décident la partition de la demande d'un fichier en utilisant soit la maximisation du débit crête, soit la stratégie assistée par réseau. On montre que cette dernière stratégie maximise le débit moyen dans l'ensemble du réseau. On montre également que les stratégies centrées sur le réseau permettent d'obtenir des débits de données plus élevés que ceux centrés sur l'utilisateur. Ensuite, on se concentre sur les réseaux d'accès radio virtuels (V-RAN) et en particulier sur l'allocation de multi-ressources. On étudie la faisabilité de la virtualisation sans diminuer ni la performance des utilisateurs, ni la stabilité du système. On considère un réseau hétérogène 5G composé de cellules LTE et mm-wave afin d'étudier comment les réseaux hauts fréquence peuvent augmenter la capacité du système. On montre que la virtualisation du réseau est réalisable sans perte de performance lors de l'utilisation de la stratégie « dominant resource fairness » (DRF). On propose une stratégie d'allocation en deux phases (TPA) qui montre un indice d'équité plus élevé que DRF et une stabilité du système plus élevée que PF. On montre également des gains importants apportés par l'adoption des fréquences mm-wave au lieu de WiFi. Finalement, on considère l'efficacité énergétique et compare les stratégies DRF et TPA avec une stratégie éconergétique basée sur l'algorithme de Dinklebach. Les résultats montrent que la stratégie éconergétique dépasse légèrement DRF et TPA à charge faible ou moyenne en termes de débit moyen plus élevé avec une consommation d'énergie comparable, alors qu'elle les surpasse à une charge élevée en termes de consommation d'énergie moins élevée. Dans ce cas de charge élevée, DRF surpasse TPA et la stratégie éconergétique en termes de débit moyen. En ce qui concerne l'indice d'équité de Jain, TPA réalise l'indice d'équité le plus élevé parmi d'autres stratégies / Fifth generation mobile networks (5G) are being designed to introduce new services that require extreme broadband data rates and utlra-reliable latency. 5G will be a paradigm shift that includes heterogeneous networks with densification, virtualized radio access networks, mm-wave carrier frequencies, and very high device densities. However, unlike the previous generations, it will be a holistic network, tying any new 5G air interface and spectrum with the currently existing LTE and WiFi. In this context, we focus on new resource allocation strategies that are able to take advantage of multihoming in dual access settings. We model such algorithms at the flow level and analyze their performance in terms of flow throughput, system stability and fairness between different classes of users. We first focus on multihoming in LTE/WiFi heterogeneous networks. We consider network centric allocations where a central scheduler performs local and global proportional fairness (PF) allocations for different classes of users, single-homed and multihomed users. By comparison with a reference model without multihoming, we show that both strategies improve system performance and stability, at the expense of more complexity for the global PF. We also investigate user centric allocation strategies where multihomed users decide the split of a file using either peak rate maximization or network assisted strategy. We show that the latter strategy maximizes the average throughput in the whole network. We also show that network centric strategies achieve higher data rates than the user centric ones. Then, we focus on Virtual Radio Access Networks (V-RAN) and particularly on multi-resource allocation therein. We investigate the feasibility of virtualization without decreasing neither users performance, nor system's stability. We consider a 5G heterogeneous network composed of LTE and mm-wave cells in order to study how high frequency networks can increase system's capacity. We show that network virtualization is feasible without performance loss when using the dominant resource fairness strategy (DRF). We propose a two-phase allocation (TPA) strategy which achieves a higher fairness index than DRF and a higher system stability than PF. We also show significant gains brought by mm-wave instead of WiFi. Eventually, we consider energy efficiency and compare DRF and TPA strategies with a Dinklebach based energy efficient strategy. Our results show that the energy efficient strategy slightly outperforms DRF and TPA at low to medium load in terms of higher average throughput with comparable power consumption, while it outperforms them at high load in terms of power consumption. In this case of high load, DRF outperforms TPA and the energy efficient strategy in terms of average throughput. As for Jain's fairness index, TPA achieves the highest one

This thesis tackles issues of particular interest regarding analysis and design of passive components at the mm-wave and Terahertz (THz) bands. Innovative analysis techniques and modeling of complex structures, design procedures, and practical implementation of advanced passive devices are presented. The first part of the thesis is dedicated to THz passive components. These days, THz technology suffers from the lack of suitable waveguiding structures since both, metals and dielectric, are lossy at THz frequencies. This implies that neither conventional closed metallic structures used at microwave frequencies, nor dielectric waveguides used in the optical regime, are adequate solutions. Among a variety of new proposals, the Single Wire Waveguide (SWW) stands out due to its low attenuation and dispersion. However, this surface waveguide presents difficult excitation and strong radiation on bends. A Dielectric-Coated Single Wire Waveguide (DCSWW) can be used to alleviate these problems, but advantages of the SWW are lost and new problems arise. Until now, literature has not given proper solution to radiation on bends and, on the other hand, rigorous characterization of these waveguides lacks these days. This thesis provides, for the first time, a complete modal analysis of both waveguides, appropriated for THz frequencies. This analysis is later applied to solve the problem of radiation on bends. Several structures and design procedures to alleviate radiation losses are presented and experimentally validated. The second part of the thesis is dedicated to mm-wave passive components. These days, when implementing passive components to operate at such small, millimetric wavelengths, to ensure proper metallic contact and alignment between parts results challenging. In addition, dielectric absorption becomes significant at mm-wave frequencies. Consequently, conventional hollow metallic waveguides and planar transmission lines present high attenuation so that new topologies are being considered. Gap Waveguides (GWs), based on a periodic structure introducing an Electromagnetic Bandgap effect, result very suitable since they do not require metallic contacts and avoid dielectric losses. However, although GWs have great potential, several issues prevent GW technology from becoming consolidated and universally used. On the one hand, the topological complexity of GWs difficulties the design process since full-wave simulations are time-costly and there is a lack of appropriate analysis methods and suitable synthesis procedures. On the other hand, benefits of using GWs instead of conventional structures are required to be more clearly evidenced with high-performance GW components and proper comparatives with conventional structures. This thesis introduces several efficient analysis methods, models, and synthesis techniques that will allow engineers without significant background in GWs to straightforwardly implement GW devices. In addition, several high-performance narrow-band filters operating at Ka-band and V-band, as well as a rigorous comparative with rectangular waveguide topology, are presented. / Esta tesis aborda problemas actuales en el análisis y diseño de componentes pasivos en las bandas de onda milimétrica y Terahercios (THz). Se presentan nuevas técnicas de análisis y modelado de estructuras complejas, procedimientos de diseño, e implementación práctica de dispositivos pasivos avanzados. La primera parte de la tesis se dedica a componentes pasivos de THz. Actualmente no se disponen de guías de onda adecuadas a THz debido a que ambos, metales y dieléctricos, introducen grandes pérdidas. En consecuencia, no es adecuado escalar las estructuras metálicas cerradas usadas en microondas, ni las guías dieléctricas usadas a frecuencias ópticas. Entre un gran número de recientes propuestas, la Single Wire Waveguide (SWW) destaca por su baja atenuación y casi nula dispersión. No obstante, como guía superficial, la SWW presenta difícil excitación y radiación en curvas. El uso de un recubrimiento dieléctrico, creando la Dielecric-Coated Single Wire Waveguide (DCSWW), alivia estos inconvenientes, pero las ventajas anteriores se pierden y nuevos problemas aparecen. Hasta la fecha, no se han encontrado soluciones adecuadas para la radiación en curvas de la SWW. Además, se echa en falta una caracterización rigurosa de ambas guías. Esta tesis presenta, por primera vez, un análisis modal completo de SWW y DCSWW, adecuado a la banda de THz. Este análisis es aplicado posteriormente para evitar el problema de la radiación en curvas. Se presentan y validan experimentalmente diversas estructuras y procedimientos de diseño. La segunda parte de la tesis abarca componentes pasivos de ondas milimétricas. Actualmente, estos componentes sufren una importante degradación de su respuesta debido a que resulta difícil asegurar contacto metálico y alineamiento adecuados para la operación a longitudes de onda tan pequeñas. Además, la absorción dieléctrica incrementa notablemente a estas frecuencias. En consecuencia, tanto guías metálicas huecas como líneas de transmisión planares convencionales presentan gran atenuación, siendo necesario considerar topologías alternativas. Las Gap Waveguides (GWs), basadas en una estructura periódica que introduce un efecto de Electromagnetic Bandgap, resultan muy adecuadas puesto que no requieren contacto entre partes metálicas y evitan las pérdidas en dieléctricos. No obstante, a pesar del potencial de las GWs, varias barreras impiden la consolidación y uso universal de esta tecnología. Por una parte, la compleja topología de las GWs dificulta el proceso de diseño dado que las simulaciones de onda completa consumen mucho tiempo y no existen actualmente métodos de análisis y diseño apropiados. Por otra parte, es necesario evidenciar el beneficio de usar GWs mediante dispositivos GW de altas prestaciones y comparativas adecuadas con estructuras convencionales. Esta tesis presenta diversos métodos de análisis eficientes, modelos, y técnicas de diseño que permitirán la síntesis de dispositivos GW sin necesidad de un conocimiento profundo de esta tecnología. Asimismo, se presentan varios filtros de banda estrecha operando en las bandas Ka y V con altas prestaciones, así como una comparativa rigurosa con la guía rectangular. / Aquesta tesi aborda problemes actuals en relació a l'anàlisi i disseny de components passius en les bandes d'ona mil·limètrica i Terahercis. Es presenten noves tècniques d'anàlisi i modelatge d'estructures complexes, procediments de disseny, i implementació pràctica de dispositius passius avançats. La primera part de la tesi es focalitza en components passius de THz. Actualment no es disposen de guies d'ona adequades a THz causa que tots dos, metalls i dielèctrics, introdueixen grans pèrdues. En conseqüència, no és adequat escalar les estructures metál·liques tancades usades en microones, ni les guies dielèctriques usades a freqüències òptiques. Entre un gran nombre de propostes recents, la Single Wire Waveguide (SWW) destaca per la seua baixa atenuació i quasi nul·la dispersió. No obstant això, com a guia superficial, la SWW presenta difícil excitació i radiació en corbes. L'ús d'un recobriment dielèctric, creant la Dielecric-Coated Single Wire Waveguide (DCSWW), alleuja aquests inconvenients, però els avantatges anteriors es perden i nous problemes apareixen. Fins a la data, no s'han trobat solucions adequades per a la radiació en corbes de la SWW. A més, es troba a faltar una caracterització rigorosa d'ambdues guies. Aquesta tesi presenta, per primera vegada, un anàlisi modal complet de SWW i DCSWW, adequat a la banda de THz. Aquest anàlisi és aplicat posteriorment per evitar el problema de la radiació en corbes. Es presenten i validen experimentalment diverses estructures i procediments de disseny. La segona part de la tesi es centra en components passius d'ones mil·limètriques. Actualment, aquests components pateixen una important degradació de la seua resposta a causa de que resulta difícil assegurar contacte metàl·lic i alineament adequats per a l'operació a longituds d'ona tan menudes. A més, l'absorció dielèctrica incrementa notablement a aquestes freqüències. En conseqüència, tant guies metàl·liques buides com línies de transmissió planars convencionals presenten gran atenuació, sent necessari considerar topologies alternatives. Les Gap Waveguides (GWs), basades en una estructura periòdica que introdueix un efecte de Electromagnetic Bandgap, resulten molt adequades ja que no requereixen contacte entre parts metàl·liques i eviten les pèrdues en dielèctrics. No obstant, tot i el potencial de les GWs, diverses barreres impedixen la consolidació i ús universal d'aquesta tecnologia. D'una banda, la complexa topologia de les GWs dificulta el procés de disseny atés que les simulacions d'ona completa consumeixen molt de temps i no existeixen actualment mètodes d'anàlisi i disseny apropiats. D'altra banda, és necessari evidenciar el benefici d'utilitzar GWs mitjançant dispositius GW d'altes prestacions i comparatives adequades amb estructures convencionals. Aquesta tesi presenta diversos mètodes d'anàlisi eficients, models, i tècniques de disseny que permetran la síntesi de dispositius GW sense necessitat d'un coneixement profund d'aquesta tecnologia. Així mateix, es presenten diversos filtres de banda estreta operant en les bandes Ka i V amb altes prestacions, així com una comparativa rigorosa amb la guia rectangular. / Berenguer Verdú, AJ. (2017). Analysis and design of efficient passive components for the millimeter-wave and THz bands [Tesis doctoral]. Universitat Politècnica de València. https://doi.org/10.4995/Thesis/10251/84004