In response to serious environmental and economic concerns, the design and production of aircrafts have been changing profoundly over the past decades with the nose-to-tail switch from metallic materials to lightweight composite materials such as carbon fibre reinforced plastic (CFRP). In this context, the present doctoral research work aimed to contribute to the development of a CFRP booster casing, a real innovation in the field initiated and conducted by Safran Aero Boosters. More specifically, this thesis addresses the matter of joining metal/CFRP hybrid structures, which are prone to possibly detrimental residual stresses.The issue is treated with an approach combining experimental characterisation and finite element (FE) simulations. The multi-layered system’s state of damage was systematically examined on hundreds of micrographs, and the outcome of this study is presented under the form of a statistical analysis. Further, the defects’ 3D morphology is investigated by incremental polishing. A number of thermal and mechanical properties are measured by diverse physical tests on part of the constituent materials, i.e. the aerospace grade RTM6 epoxy resin, the structural Redux 322 epoxy film adhesive, and AISI 316L stainless steel. They are used as input data in a FE model of the multilayer that is developed and progressively refined to obtain detailed residual stress fields after thermal loading. These results are compared to experimental data acquired by X-ray diffraction stress analysis and with the curvature-based Stoney formula. Cohesive elements are placed at specific locations within the FE model to allow simulating progressive damage. Peel tests, mode I, mode II and mixed mode I/II fracture tests are thus performed in view of measuring the joint toughness. The results of these tests are discussed and the presence of residual stress in the fracture specimens is highlighted. Key information for the calibration of the cohesive law is finally identified via inverse FE analysis of the mode I test, this being a significant step in the process of building a damage predictive FE model of the multi-layered system. / Doctorat en Sciences de l'ingénieur et technologie / info:eu-repo/semantics/nonPublished

Indiana University-Purdue University Indianapolis (IUPUI) / This study seeks to improve the understanding of inlet conditions of a large rotor-stator cavity in a turbofan engine, often referred to as the drive cone cavity (DCC). The inlet flow is better understood through a higher fidelity computational fluid dynamics (CFD) modeling of the inlet to the cavity, and a coupled finite element (FE) thermal to CFD fluid analysis of the cavity in order to accurately predict engine component temperatures. Accurately predicting temperature distribution in the cavity is important because temperatures directly affect the material properties including Young's modulus, yield strength, fatigue strength, creep properties. All of these properties directly affect the life of critical engine components. In addition, temperatures cause thermal expansion which changes clearances and in turn affects engine efficiency. The DCC is fed from the last stage of the high pressure compressor. One of its primary functions is to purge the air over the rotor wall to prevent it from overheating. Aero-thermal conditions within the DCC cavity are particularly challenging to predict due to the complex air flow and high heat transfer in the rotating component. Thus, in order to accurately predict metal temperatures a two-way coupled CFD-FE analysis is needed. Historically, when the cavity airflow is modeled for engine design purposes, the inlet condition has been over-simplified for the CFD analysis which impacts the results, particularly in the region around the compressor disc rim. The inlet is typically simplified by circumferentially averaging the velocity field at the inlet to the cavity which removes the effect of pressure wakes from the upstream rotor blades. The way in which these non-axisymmetric flow characteristics affect metal temperatures is not well understood. In addition, a constant air temperature scaled from a previous analysis is used as the simplified cavity inlet air temperature. Therefore, the objectives of this study are: (a) model the DCC cavity with a more physically representative inlet condition while coupling the solid thermal analysis and compressible air flow analysis that includes the fluid velocity, pressure, and temperature fields; (b) run a coupled analysis whose boundary conditions come from computational models, rather than thermocouple data; (c) validate the model using available experimental data; and (d) based on the validation, determine if the model can be used to predict air inlet and metal temperatures for new engine geometries. Verification with experimental results showed that the coupled analysis with the 3D no-bolt CFD model with predictive boundary conditions, over-predicted the HP6 offtake temperature by 16k. The maximum error was an over-prediction of 50k while the average error was 17k. The predictive model with 3D bolts also predicted cavity temperatures with an average error of 17k. For the two CFD models with predicted boundary conditions, the case without bolts performed better than the case with bolts. This is due to the flow errors caused by placing stationary bolts in a rotating reference frame. Therefore it is recommended that this type of analysis only be attempted for drive cone cavities with no bolts or shielded bolts.

[ES] En un presente marcado por la continua lucha contra la contaminación y el cambio climático, la investigación en mejoras tecnológicas que permitan una transición aceptable para la sociedad hacia un futuro más ecológico ocupa un papel fundamental. En concreto, la aviación es un foco constante de innovación, ya que es considerada una función indispensable en una sociedad tan globalizada como la actual, pero con unos niveles de contaminación preocupantes. En este aspecto, el desarrollo de motores con altas eficiencias es un paso clave para la transición medioambiental. Sin embargo, estas alternativas presentan un reto tecnológico en cuanto a su gestión térmica basado, principalmente, en la necesidad de aumentar la refrigeración. En este contexto e impulsada por el proyecto "Aerodynamic upgrade of Surface Air Cooled Oil Cooler (SACOC)" de Clean Sky 2, esta tesis doctoral se centra en el estudio experimental de geometrías de intercambiadores de calor de superficie para la refrigeración del aceite motor mediante el uso del aire del flujo secundario del turbofan. Actualmente, existen una serie de limitaciones en cuanto a las capacidades para llevar a cabo un análisis y diseño detallado de este tipo de intercambiadores de calor debido a la falta de instalaciones que permitan un correcta, completa y robusta caracterización experimental. Las principales fuentes de datos se basan en cálculos numéricos validados a partir de extrapolaciones en condiciones de cuestionable aplicabilidad. A lo largo de la tesis se presentan los resultados obtenidos tras una detallada caracterización de cuatro diferentes geometrías de intercambiadores de calor empleando tanto técnicas intrusivas como ópticas. Se utiliza un banco de flujo capaz de generar una corriente de aire típica alrededor de los intercambiadores, mientras que un sistema de acondicionamiento de aceite controla el punto de operación por el lado caliente. Para recrear de manera más realista las condiciones de funcionamiento, se presenta una metodología para generar de manera automática pantallas de distorsión que pueden reproducir una distribución bidimensional de velocidades objetivo mediante la manufactura aditiva de paneles de porosidad variable. Este modelo, analizado mediante CFD y validado experimentalmente, se utiliza para reproducir el perfil de velocidades típico presente en torno al intercambiador en una circunstancia real de operación. Tras definir métricas relevantes que permitan analizar el comportamiento de las distintas geometrías, se llega a la conclusión de que los problemas aerodinámico y térmico están altamente acoplados en estos dispositivos, demostrando la necesidad de un cuidadoso diseño para mejorar las actuaciones del intercambiador. Los resultados muestran que puede llegar a obtenerse una mejora de más de un 12% en la caída de presión y casi un 20% en el intercambio de calor. Además, se ha confirmado el impacto del uso de la pantalla de distorsión, con variaciones del orden de 10% en ambas variables. Los resultados también muestran que es posible realizar una caracterización preliminar de manera fiable con un modelo impreso en 3D, en cuanto campos de velocidades, pérdidas de presión y frecuencias propias corregidas. Con el análisis llevado a cabo en esta tesis, se puede concluir que es fundamental tener una instalación experimental que reproduzca las condiciones de funcionamiento reales de un motor para realizar estudios relevantes de intercambiadores de calor. Además, es necesario el uso de métricas adecuadas junto con el desarrollo de una metodología exhaustiva, fiable y robusta. Los resultados y metodología presentados en en esta investigación pueden llegar a tener un impacto importante tanto a nivel académico como industrial, ya que abren la puerta a desarrollar sistemas de gestión térmica más eficiente en unas etapas de diseño preliminares que son más asequibles económicamente, consumen menos tiempo y tienen mayor flexibilidad para introducir modificaciones. / [CAT] En un present marcat per la lluita contínua contra la contaminació i el canvi climàtic, la recerca en millores tecnològiques que permetin una transició acceptable per a la societat cap a un futur més ecològic ocupa un paper fonamental. En concret, l'aviació és un focus constant d'innovació, ja que és considerada una funció indispensable en una societat tan globalitzada com l'actual però amb uns nivells de contaminació preocupants. En aquest aspecte, el desenvolupament de motors amb altes eficiències és un pas clau per a la transició mediambiental. Tot i això, aquestes alternatives presenten un repte tecnològic quant a la seva gestió tèrmica basat, principalment, en la necessitat d'augmentar la refrigeració. En aquest context i impulsada pel projecte "Aerodynamic upgrade of Surface Air Cooled Oil Cooler (SACOC)" de Clean Sky 2, aquesta tesi doctoral se centra en l'estudi experimental de geometries d'intercanviadors de calor de superfície per a la refrigeració de l'oli motor mitjançant l'ús de l'aire del flux secundari del turbofan. Actualment, hi ha una sèrie de limitacions quant a les capacitats per dur a terme una anàlisi i disseny detallat d'aquest tipus d'intercanviadors de calor a causa de la manca d'instal·lacions que permetin una caracterització experimental correcta, completa i robusta. Les fonts de dades principals es basen en càlculs numèrics validats a partir d'extrapolacions en condicions de qüestionable aplicabilitat. Al llarg de la tesi es presenten els resultats obtinguts després d'una detallada caracterització de quatre geometries diferents d'intercanviadors de calor emprant tant tècniques intrusives com òptiques. Sutilitza un banc de flux capaç de generar un corrent daire típic al voltant dels intercanviadors, mentre que un sistema de condicionament doli controla el punt doperació pel costat calent. Per recrear de manera més realista les condicions de funcionament, es presenta una metodologia per generar de manera automàtica pantalles de distorsió que poden reproduir una distribució bidimensional de velocitats objectiu mitjançant la manufactura additiva de panells de porositat variable. Aquest model, analitzat mitjançant CFD i validat experimentalment, sutilitza per reproduir el perfil de velocitats típic present al voltant de lintercanviador en una circumstància real doperació. Després de definir mètriques rellevants que permetin analitzar el comportament de les diferents geometries, s'arriba a la conclusió que els problemes aerodinàmic i tèrmic estan altament acoblats en aquests dispositius, demostrant la necessitat d'un disseny acurat per millorar les actuacions de l'intercanviador. Els resultats mostren que es pot arribar a obtenir una millora de més d'un 12% a la caiguda de pressió i gairebé un 20% a l'intercanvi de calor. A més, s'ha confirmat l'impacte de l'ús de la pantalla de distorsió, amb variacions de l'ordre del 10% a les dues variables. Els resultats també mostren que és possible fer una caracterització preliminar de manera fiable amb un model imprès en 3D, en tant que camps de velocitats, pèrdues de pressió i freqüències pròpies corregides. Amb l'anàlisi duta a terme en aquesta tesi, es pot concloure que és fonamental tenir una instal·lació experimental que reprodueixi les condicions de funcionament reals d'un motor per fer estudis rellevants d'intercanviadors de calor. A més, cal fer servir mètriques adequades juntament amb el desenvolupament d'una metodologia exhaustiva, fiable i robusta. Els resultats i metodologia presentats en aquesta investigació poden arribar a tenir un impacte important tant a nivell acadèmic com industrial, ja que obren la porta a desenvolupar sistemes de gestió tèrmica més eficient en unes etapes de disseny preliminars que són més assequibles econòmicament, consumeixen menys temps i tenen més flexibilitat per introduir modificacions. / [EN] In a present marked by the continuous fight against pollution and climate change, research into technological improvements that allow an acceptable transition for society towards a greener future occupies a fundamental role. Specifically, aviation is a constant focus of innovation, since it is considered an essential function in a society as globalized as today's, but with worrying levels of pollution. In this regard, the development of motors with high efficiencies is a key step for the environmental transition. However, these alternatives present a technological challenge in terms of their thermal management, based mainly on the need to increase cooling. In this context and promoted by the Clean Sky 2 "Aerodynamic upgrade of Surface Air Cooled Oil Cooler (SACOC)" project, this doctoral thesis focuses on the experimental study of surface heat exchanger geometries for engine oil cooling using the use of secondary flow air from the turbofan. Currently, there are a number of limitations regarding the capacity to carry out a detailed analysis and design of this type of heat exchanger due to the lack of facilities that allow a correct, complete and robust experimental characterization. The main data sources are based on numerical calculations validated from extrapolations under conditions of questionable applicability. The thesis presents results after a detailed characterization of four different geometries of heat exchangers using both intrusive and optical techniques. A flow bench capable of generating a typical air current around the exchangers is used, while an oil conditioning system controls the point of operation on the hot side. To more realistically recreate operating conditions, a methodology is presented to automatically generate distortion screens that can reproduce a two-dimensional distribution of target velocities through additive manufacturing of variable porosity panels. This model, analyzed by means of CFD and validated experimentally, is used to reproduce the typical speed profile present around the exchanger in a real operating circumstance. After defining relevant metrics that allow analyzing the behaviour of the different geometries, it is concluded that aerodynamic and thermal problems are highly coupled in these devices, demonstrating the need for careful design to improve the exchanger's performance. The results show that an improvement of more than 12% in pressure drop and almost 20% in heat exchange can be obtained. In addition, the impact of using the distortion screen has been confirmed, with variations of the order of 10% in both variables. The results also show that it is possible to carry out a preliminary characterization in a reliable way with a 3D printed model, in terms of velocity fields, pressure losses and corrected eigenfrequencies. With the analysis carried out in this thesis, it can be concluded that it is essential to have an experimental installation that reproduces the real operating conditions of an engine to carry out relevant studies of heat exchangers. In addition, the use of appropriate metrics is necessary together with the development of a comprehensive, reliable and robust methodology. The results and methodology presented in this research can have a significant impact both at an academic and industrial level, since they open the door to developing more efficient thermal management systems in preliminary design stages that are more affordable, consume less time and have more flexibility to make changes. / The respondent wishes to acknowledge the financial support received through the Programa de Apoyo para la Investigación y Desarrollo (PAID) of Univer- sitat Politècnica de València under grant PAID-01-20 n◦ 21589. This project has received funding from the Clean Sky 2 Joint Undertak- ing under the European Unions Horizon 2020 research and innovation pro- gramme under grant agreement No 831977 Aerodynamic upgrade of Sur- face Air-Cooled Oil Coolers (SACOC) / Felgueroso Rodríguez, A. (2023). Aerothermal Characterisation of Surface Heat Exchangers for Turbofans [Tesis doctoral]. Universitat Politècnica de València. https://doi.org/10.4995/Thesis/10251/195852

Purpose - This master thesis evaluates the hybrid-electric aircraft project E-Fan X with respect to its economical and environmental performance in comparison to its reference aircraft, the BAe 146-100. The E-Fan X is replacing one of the four jet engines of the reference aircraft by an electric motor and a fan. A turboshaft engine in the cargo compartment drives a generator to power the electric motor. --- Methodology - The evaluation of this project is based on standard aircraft design equations. Economics are based on Direct Operating Costs (DOC), which are calculated with the method of the Association of European Airlines (AEA) from 1989, inflated to 2019 values. Environmental impact is assessed based on local air quality (NOx, Ozone and Particulate Matter), climate impact (CO2, NOx, Aircraft-Induced Cloudiness known as AIC) and noise pollution estimated with fundamental acoustic equations. --- Findings - The battery on board the E-Fan X it is not necessary. In order to improve the proposed design, the battery was eliminated. Nevertheless, due to additional parts required in the new configuration, the aircraft is 902 kg heavier. The turboshaft engine saves only 59 kg of fuel. The additional mass has to be compensated by a payload reduced by 9 passengers. The DOC per seat-mile are up by more than 10% and equivalent CO2 per seat-mile are more than 16% up in the new aircraft. --- Research limitations - Results are limited in accuracy by the underlying standard aircraft design calculations. The results are also limited in accuracy by the lack of knowledge of some data of the project. --- Practical implications - The report contributes arguments to the discussion about electric flight. --- Social implications - Results show that unconditional praise given to the environmental characteristics of this industry project are not justified.

The path to future aero-engines with more efficient engine architectures requires advanced thermal management technologies to handle the demand of refrigeration and lubrication. Oil systems, holding a double function as lubricant and coolant circuits, require supplemental cooling sources to the conventional fuel based cooling systems as the current oil thermal capacity becomes saturated with future engine developments. The present research focuses on air/oil coolers, which geometrical characteristics and location are designed to minimize aerodynamic effects while maximizing the thermal exchange. The heat exchangers composed of parallel fins are integrated at the inner wall of the secondary duct of a turbofan. The analysis of the interaction between the three-dimensional high velocity bypass flow and the heat exchangers is essential to evaluate and optimize the aero-thermodynamic performances, and to provide data for engine modeling. The objectives of this research are the development of engine testing methods alternative to flight testing, and the characterization of the aerothermal behavior of different finned heat exchanger configurations. A new blow-down wind tunnel test facility was specifically designed to replicate the engine bypass flow in the region of the splitter. The annular sector type test section consists on a complex 3D geometry, as a result of three dimensional numerical flow simulations. The flow evolves over the splitter duplicated at real scale, guided by helicoidally shaped lateral walls. The development of measurement techniques for the present application involved the design of instrumentation, testing procedures and data reduction methods. Detailed studies were focused on multi-hole and fine wire thermocouple probes. Two types of test campaigns were performed dedicated to: flow measurements along the test section for different test configurations, i.e. in the absence of heat exchangers and in the presence of different heat exchanger geometries, and heat transfer measurements on the heat exchanger. As a result contours of flow velocity, angular distributions, total and static pressures, temperatures and turbulence intensities, at different bypass duct axial positions, as well as wall pressures along the test section, were obtained. The analysis of the flow development along the test section allowed the understanding of the different flow behaviors for each test configuration. Comparison of flow variables at each measurement plane permitted quantifying and contrasting the different flow disturbances. Detailed analyses of the flow downstream of the heat exchangers were assessed to characterize the flow in the fins¿ wake region. The aerodynamic performance of each heat exchanger configuration was evaluated in terms of non dimensional pressure losses. Fins convective heat transfer characteristics were derived from the infrared fin surface temperature measurements through a new methodology based on inverse heat transfer methods coupled with conductive heat flux models. The experimental characterization permitted to evaluate the cooling capacity of the investigated type of heat exchangers for the design operational conditions. Finally, the thermal efficiency of the heat exchanger at different points of the flight envelope during a typical commercial mission was estimated by extrapolating the convective properties of the flow to flight conditions. / Villafañe Roca, L. (2013). Experimental Aerothermal Performance of Turbofan Bypass Flow Heat Exchangers [Tesis doctoral no publicada]. Universitat Politècnica de València. https://doi.org/10.4995/Thesis/10251/34774 / TESIS