In recent years, the wireless industry has witnessed tremendous development for the defense and commercial segments. The explosive growth in the modern radio frequency and microwave systems leads to an increased interest in the research of miniaturized microwave circuits with superior performance. Broadband components, in particular band pass filters (BPFs) and couplers are some of the widely used components in the modern communication systems, software defined radios, cognitive radios, imaging systems and positioning radars. In order to meet these requirements, the use of innovative geometries, a thorough understanding of their behavior by appropriate analytical techniques and the use of appropriate fabrication approaches are essential. This thesis is an effort in this direction. In this thesis work, an aperture in the ground plane is used to achieve the tight coupling in the edge and broadside-coupled coupled lines which may be otherwise difficult due to the fabrication limitations. Since microstrip lines with an aperture in the ground plane are found to be very useful in various MIC and MMIC components, closed form analytical expressions developed here will be useful for their initial synthesis. The performances of components using these are enhanced using open/short circuited resonators, spurlines and stubs. A quasi-static approach has been investigated to obtain simple closed form expressions for a microstrip line with a rectangular aperture in the ground plane. The effect of a rectangular aperture in the ground plane has been incorporated in the commonly used expressions of a regular microstrip line by introducing the concept of an equivalent effective height. The expressions for the effective height microstrip geometries with defected ground are obtained and this has been further extended to various possibilities of two-conductor and three-conductor coupled lines. Analysis of the filters and the couplers are mainly based on the even and odd mode propagation characteristics of coupled lines. This approach is extended in this thesis for three conductor coupled lines. Novel broadband BPFs and couplers and dual band pass filters employing various coupled line configurations and defected ground have been developed in this research work. Most of these components have been implemented on a regular microwave laminate or LTCC medium (planar or multi-layer) and tested for the required RF performances. The experimental results were compared against the analytically computed results based on the circuit models and the full wave simulations using electromagnetic (EM) simulations for the validation. The results are in good agreement. With practical requirements of the organization in mind, additional design elements such as open circuit stubs have been incorporated in some of these designs to achieve the desired performance. It is expected that the wideband filter (3.0GHz to 3.8GHz) and the broadband coupler (4GHz to 6GHz) developed in this thesis work would be deployed in systems developed at the Central Research Laboratory, Bharat Electronics Limited, Bangalore, India. In summary, the present doctoral work strives to (i) establish a simplified analysis method for the microstrip lines and coupled microstrip lines with a rectangular aperture in the ground plane, (ii) extend the even and odd mode analysis of the coupled lines for several new coupled line configurations, (iii) design novel broadband microwave filters, dual band filter and couplers using both these, (iv) fabricate these devices using the planar technologies including LTCC, and (v) validate the analysis and design with important practical applications.

The emergence of Ultra-wideband (UWB) technology application has yielded tremendous and vital impacts in the field of microwave wireless communications. These applications include military radar imaging, security screening, and tumour detection, especially for early detection of breast cancer. These indicators have stimulated and inspired many researchers to make the best use of this promising technology. UWB technology challenges such as antenna design, the problem of imaging reconstruction techniques, challenges of severe signal attenuation and dispersion in high loss material. Others are lengthy computational time demand and large computer memory requirements are prevalent constraints that need to be tackled especially in a large scale and complex computational electromagnetic analysis. In this regard, it is necessary to find out recently developed optimisation techniques that can provide solutions to these problems. In this thesis, designing, optimisation, development, measurement, and analysis of UWB antennas for near-field microwave imaging applications are considered. This technology emulates the same concept of surface penetrating radar operating in various forms of the UWB spectrum. The initial design of UWB monopole antennas, including T-slots, rectangular slots, and hexagonal slots on a circular radiating patch, was explicitly implemented for medical imaging applications to cover the UWB frequency ranging from 3.1 GHz to 10.6 GHz. Based on this concept, a new bow-tie and Vivaldi UWB antennas were designed for a through-the-wall imaging application. The new antennas were designed to cover a spectrum on a lower frequency ranging from 1 GHz - 4 GHz to ease the high wall losses that will be encountered when using a higher frequency range and to guarantee deeper penetration of the electromagnetic wave. Finally, both simulated and calculated results of the designed, optimised antennas indicate excellent agreement with improved performance in terms of return loss, gain, radiation pattern, and fidelity over the entire UWB frequency. These breakthroughs provided reduced computational time and computer memory requirement for useful, efficient, reliable, and compact sensors for imaging applications, including security and breast cancer detection, thereby saving more lives. / Tertiary Education Trust Fund (TET Fund) Supported by the Nigerian Defence Academy (NDA)

La presenta Tesis Doctoral encuentra su ámbito de aplicación en redes de acceso ópticas de fibra hasta el hogar o FTTH (del inglés fibre-to-the-home). Las redes FTTH han sido ampliamente desplegadas en todo el mundo y se prevé que evolucionen hasta arquitecturas de multiplexación por división en longitud de onda o WDM(dle inglés wavelength division multiplexing). Conforme los requerimientos de capacidady ancho de banda por usuario para servicios de comunicación de banda ancha se incrementan continuamente, tecnologías tales como hybrid wireless-optical, radio de banda ultra ancha o UWB(del inglés ultra-wideband), y radio de onda milimétrica se están investigando como soluciones viables para proporcionar tasas de datos excediendo Gigabit por segundo por usuario. Las redes híbridas inalámbrico-óptico pueden proporcionar backhaul más simple y se prevé que desempeñen un papel importante en redes de acceso de próxima generación que requerirán despliegue flexible, alta capacidad, habilidad de ampliación, escalable en número de usuarios y demanda, y factible económicamente. Las técnicas radio sobre fibra combinadas con sistemas inalámbricos multigigabit que proporcionen capacidades comparables a sistemas de comunicaciones de fibra óptica se ve como una solución rápidamente desplegable y efectiva en coste para proporcionar acceso transparente cableado/inalámbrico integrado a servicios de banda ancha para el usuario final. Los sistemas inalámbricos UWB y de onda milimétrica son capaces de proporcionar comunicaciones multigigabit. UWB en particular permite un uso eficiente del esprectro 3.1-10.6 GHz debido a sus características únicas de coexistencia y tiene madurez de mercado. Sin embargo, la tecnología UWB está restringida por regulación en todo el mundo. Esta restricción de regulación hace de gran interés a la radio de onda milimétrica en 60 GHz debido al aproximadamente 7 GHz de ancho de banda regulado consistentemente en todo el mundo, sin restricciones de coexistencia. / Beltrán Ramírez, M. (2012). Photonic Techniques for Next-Generation Integrated Optical Networks Based on Ultra-Wideband Radio / Técnicas Fotónicas para Redes Ópticas Integradas de Próxima Generación Basadas en Radio de Banda Ultra Ancha [Tesis doctoral]. Universitat Politècnica de València. https://doi.org/10.4995/Thesis/10251/15576

The prevalence of wireless standards and the introduction of dynamic standards/applications, such as software-defined radio, necessitate the next generation wireless devices that integrate multiple standards in a single chip-set to support a variety of services. To reduce the cost and area of such multi-standard handheld devices, reconfigurability is desirable, and the hardware should be shared/reused as much as possible. This research proposes several novel circuit topologies that can meet various specifications with minimum cost, which are suited for multi-standard applications. This doctoral study has two separate contributions: 1. The low noise amplifier (LNA) for the RF front-end; and 2. The analog-to-digital converter (ADC). The first part of this dissertation focuses on LNA noise reduction and linearization techniques where two novel LNAs are designed, taped out, and measured. The first LNA, implemented in TSMC (Taiwan Semiconductor Manufacturing Company) 0.35Cm CMOS (Complementary metal-oxide-semiconductor) process, strategically combined an inductor connected at the gate of the cascode transistor and the capacitive cross-coupling to reduce the noise and nonlinearity contributions of the cascode transistors. The proposed technique reduces LNA NF by 0.35 dB at 2.2 GHz and increases its IIP3 and voltage gain by 2.35 dBm and 2dB respectively, without a compromise on power consumption. The second LNA, implemented in UMC (United Microelectronics Corporation) 0.13Cm CMOS process, features a practical linearization technique for high-frequency wideband applications using an active nonlinear resistor, which obtains a robust linearity improvement over process and temperature variations. The proposed linearization method is experimentally demonstrated to improve the IIP3 by 3.5 to 9 dB over a 2.5–10 GHz frequency range. A comparison of measurement results with the prior published state-of-art Ultra-Wideband (UWB) LNAs shows that the proposed linearized UWB LNA achieves excellent linearity with much less power than previously published works. The second part of this dissertation developed a reconfigurable ADC for multistandard receiver and video processors. Typical ADCs are power optimized for only one operating speed, while a reconfigurable ADC can scale its power at different speeds, enabling minimal power consumption over a broad range of sampling rates. A novel ADC architecture is proposed for programming the sampling rate with constant biasing current and single clock. The ADC was designed and fabricated using UMC 90nm CMOS process and featured good power scalability and simplified system design. The programmable speed range covers all the video formats and most of the wireless communication standards, while achieving comparable Figure-of-Merit with customized ADCs at each performance node. Since bias current is kept constant, the reconfigurable ADC is more robust and reliable than the previous published works.

Having a device with the capability of measure motions from gait produced by a human being, could be of most importance in medicine and sports. Physicians or researchers could measure and analyse key features of a person's gait for the purpose of rehabilitation or science, regarding neurological disabilities. Also in sports, professionals and hobbyists could use such a device for improving their technique or prevent injuries when performing. In this master thesis, I present the research of what technology is capable of today, regarding gait analysis devices. The research that was done has then help the development of a suggested standalone hardware sensor node for a Body Area Network, that can support research in gait analysis. Furthermore, several algorithms like for instance UWB Real-Time Location and Dead Reckoning IMU/AHRS algorithms, have been implemented and tested for the purpose of measuring motions and be able to run on the sensor node device. The work in this thesis shows that a IMU sensor have great potentials for generating high rate motion data while performing on a small mobile device. The UWB technology on the other hand, indicates a disappointment in performance regarding the intended application but can still be useful for wireless communication between sensor nodes. The report also points out the importance of using a high performance micro controller for achieving high accuracy in measurements.

Cooperative wireless communication is an attractive technique to explore the spatial channel resources by coordination across multiple links, which can greatly improve the communication performance over single links. In this dissertation, we study the cooperative multi-link channel properties by geometric approaches in body area networks (BANs) and cellular networks respectively.<p><p>In the part of BANs, the dynamic narrowband on-body channels under body motions are modeled statistically on their temporal and spatial fading based on anechoic and indoor measurements. Common body scattering is observed to form inter-link correlation between links closely distributed and between links having synchronized movements of communication nodes. An analytical model is developed to explain the physical mechanisms of the dynamic body scattering. The on-body channel impacts to simple cooperation protocols are evaluated based on realistic measurements. <p><p>In the part of cellular networks, the cluster-level multi-link COST 2100 MIMO channel model is developed with concrete modeling concepts, complete parameterization and implementation methods, and a compatible structure for both single-link and multi-link scenarios. The cluster link-commonness is introduced to the model to describe the multi-link properties. The multi-link impacts by the model are also evaluated in a distributed MIMO system by comparing its sum-rate capacity at different ratios of cluster link-commonness. / Doctorat en Sciences de l'ingénieur / info:eu-repo/semantics/nonPublished

Η πληθώρα των εφαρμογών που μπορεί να εξυπηρετήσει η τεχνολογία Υπερευρείας Ζώνης (UWB), από τα ασύρματα προσωπικά δίκτυα υψηλών ταχυτήτων, μέχρι τα ασύρματα δίκτυα αισθητήρων με δυνατότητες ακριβούς εντοπισμού θέσης, και τα ασύρματα δίκτυα ιατρικών αισθητήρων, έχει προκαλέσει έντονο ερευνητικό ενδιαφέρον γύρω από τις υλοποιήσεις UWB συστημάτων. Η ασυνήθιστα μεγάλη περιοχή συχνοτήτων που έχει ανατεθεί στο UWB, από τα 3.1-10.6 GHz, επιτρέπει την επίτευξη υψηλών ταχυτήτων με απλά σχήματα διαμόρφωσης, ωστόσο, λόγω της διαμοίρασης του φάσματος με τις υφιστάμενες τεχνολογίες ασύρματης δικτύωσης, οι UWB εκπομπές πρέπει να περιορίζονται σε ισχύ κάτω από το κατώφλι των -41.3 dBm/MHz, ικανοποιώντας πολύ αυστηρές μάσκες εκπομπής που εισάγουν έντονες προκλήσεις στη σχεδίαση των πομπών. Η υλοποίηση αναδιατάξιμων UWB πομπών σε σύγχρονες CMOS τεχνολογίες, με υψηλή φασματική ευελιξία, ταχύτητα και ποιότητα διαμόρφωσης, καθώς και με χαμηλή κατανάλωση, αποτέλεσε το αντικείμενο της συγκεκριμένης διατριβής. Υιοθετώντας την αρχιτεκτονική Multi-Band Impulse-Radio (MB-IR) σε συνδυασμό με την τεχνική Direct Sequence BPSK, η έρευνα προσανατολίστηκε προς την ανάπτυξη καινοτόμων μονάδων βασικής ζώνης, με στόχο την ενεργειακά αποδοτική αντιστροφή Γκαουσιανών μορφοποιημένων παλμών υψηλής ποιότητας φάσματος και διάρκειας μικρότερης ακόμα και από 1 nsec. Προς αυτή την κατεύθυνση, αναπτύχθηκε μια καινοτόμα γεννήτρια Γκαουσιανών παλμών με πολύ χαμηλούς πλευρικούς λοβούς στο φάσμα, τυπικά κάτω από -40 dB, ώστε να υποστηρίζονται οι αυστηρότερες μάσκες εκπομπής ή και μελλοντικές. Η σχεδίασης της προτεινόμενης γεννήτριας είχε ως κριτήριο την ευέλικτη ρύθμιση της διάρκειας των παραγόμενων παλμών, και αξιοποίησε τη χαρακτηριστική μεταφοράς τάσης ενός ωμικά φορτωμένου, ασύμμετρου CMOS αντιστροφέα. Η γεννήτρια βασίζεται κυρίως σε ψηφιακά κυκλώματα πολύ χαμηλής τάσης και, σε σύγκριση με τις υφιστάμενες υλοποιήσεις, παρουσιάζει σημαντικό προβάδισμα στον τομέα της ταχύτητας, καθώς και στο πλάτος εξόδου, η μεγάλη τιμή του οποίου χαλαρώνει σημαντικά τη σχεδίαση του RF front end. Η γεννήτρια μελετήθηκε διεξοδικά, διεξήχθη ανάλυση κλιμάκωσης, έγινε εξαγωγή σχεδιαστικών εξισώσεων και αναπτύχθηκαν εργαλεία λογισμικού για την αυτοματοποιημένη σχεδίασή της. Για περαιτέρω αύξηση της ταχύτητας των παλμικών σημάτων εφαρμόσθηκε ειδική σχεδίαση, η οποία αντιπραγματεύεται την ταχύτητα με το επίπεδο των λοβών του φάσματος. Για την αποδοτική BSPK διαμόρφωση των Γκαουσιανών παλμών αναπτύχθηκε ειδική τοπολογία “Μεταγωγής Σήματος Πυροδότησης Πλήρους Ισορροπίας με Up-Conversion”. Η τοπολογία αυτή, σε αντίθεση με τις ανταγωνιστικές τοπολογίες, αποφεύγει την αντιστροφή του παλμού με αναλογικά κυκλώματα υψηλής κατανάλωσης, αλλά και την αναλογική μεταγωγή, καθώς η διαμόρφωση λαμβάνει χώρα πριν από την παραγωγή των παλμών. Παράλληλα, επιτυγχάνονται υψηλοί ρυθμοί, καθώς και υψηλή ποιότητα διαμόρφωσης λόγω των ισορροπημένων μονοπατιών της τοπολογίας. Η γεννήτρια μαζί με το διαμορφωτή αποτελούν τις καινοτόμες παρεμβάσεις στη μονάδα Βασικής Ζώνης του προτεινόμενου πομπού. Για την ολοκλήρωση της λειτουργικότητας του πομπού, αναπτύχθηκε ένα RF front end, το οποίο αποτελείται από έναν διπλά ισορροπημένο μίκτη, έναν LO buffer, ένα μετατροπέα διαφορικού σήματος σε απλό, και έναν ενισχυτή ισχύος, ο οποίος είναι προσαρμοσμένος στα 50 Ohms, χωρίς να απαιτεί κανένα εξωτερικό στοιχείο. Το RF front end ολοκληρώθηκε μαζί με τη μονάδα βασικής ζώνης, και ο ολοκληρωμένος πομπός κατασκευάστηκε σε τεχνολογία CMOS 130 nm. Το ολοκληρωμένο προσαρτήθηκε στην RF πλακέτα συστήματος με την τεχνική Chip on Board. Για την επιτυχία του συστήματος με την πρώτη προσπάθεια έγινε συσχεδίαση σε επίπεδο IC-Package-PCB, δίνοντας ιδιαίτερη έμφαση στα ζητήματα Signal/Power Integrity. Ο πομπός παρουσίασε την υψηλότερη ταχύτητα από τις ανταγωνιστικές MB-IR UWB υλοποιήσεις, ίση με 1.5 Gbps, με αντίστοιχη ενεργειακή αποδοτικότητα 21 pJoule/bit και μέτρο διανυσματικού σφάλματος 5.5%. Ο πομπός βελτίωσε τους πλευρικούς λοβούς στο φάσμα περισσότερο από 10 dB, ενώ η διατριβή, εκμεταλλευόμενη την αναδιαταξιμότητα του πομπού, παρουσιάζει, επιπλέον, τις πρώτες μετρήσεις σε ταχύτητες εκατοντάδων Mbps για ικανοποίηση της χαμηλής ζώνης της πρόσφατα θεσμοθετημένης, και εξαιρετικά αυστηρής, ευρωπαϊκής μάσκας εκπομπής. / The multitude of applications that Ultra-Wideband (UWB) technology can serve, from high-speed Wireless Personal Area Networks, to Wireless Sensor Networks with precision Geolocation abilities, and Wireless Medical Networks, has attracted intense research interest in the implementation of UWB systems. The unusually wide range of frequencies assigned to UWB, from 3.1-10.6 GHz, allows UWB systems employing low order modulation schemes to enjoy high throughput at low power consumption. However, since UWB shares the spectrum with existing wireless networking technologies, UWB emissions must be limited to a power spectral density below the threshold of -41.3 dBm/MHz, satisfying very stringent emission masks and introducing great challenges in the design of UWB transmitters. The subject of this thesis is the design of low power, fully integrated, reconfigurable CMOS UWB transmitters, with high spectral flexibility, high speed and high modulation quality. Adopting the Multi-Band Impulse-Radio architecture, in conjunction with the Direct Sequence BPSK modulation, the research focused on the development of a baseband unit, able to precisely invert Gaussian shaped, subnanosecond pulses. The key contributions of this thesis are a CMOS Gaussian Pulse Generator and a BSPK modulation topology, which jointly constitute the proposed baseband unit. The Pulse Generator (PG) is based on non-linear shaping, so as to facilitate the configurability of the output pulse duration, and exploits the voltage transfer characteristic of a Resistive Loaded Asymmetrical CMOS Inverter, which results in spectral sidelobes typically better than -40 dB. The PG incorporates mostly-digital low voltage circuits, while the MOSFET devices that undertake the pulse shaping avoid exclusive operation in weak inversion, in contrast to previous implementations. Consequently, the proposed CMOS PG is able to support higher throughput, as well as higher output amplitude, which relaxes considerably the design of the RF front end. This thesis presents a systematic design procedure and a scaling analysis of the non-linear pulse shaper. Moreover, in order to further increase the speed, a special PRF boost technique is proposed, which trades off speed and spectral efficiency for the spectral sidelobes level. Regarding the BPSK modulator, this work introduces the “Trigger Switching Fully Balanced Up-Conversion” topology, which avoids the use of power-hungry and distortion-prone analog circuits for the accurate inversion of the subnanosecond shaped pulses, as well as avoids the application of analog waveform switching to the baseband pulses, since the baseband modulation takes place before the generation of the pulses. The digital nature of the switching lends itself to high data rates, while the balanced paths of the topology ensure high modulation quality with minimal design effort. Wafer probing measurements confirmed the high performance of the baseband unit. The functionality of the transmitter was completed by the development of an RF front end which consists of a double balanced mixer, an LO buffer, a differential to single-ended (DtoSE) converter, and a power amplifier which is ready to drive a 50 Ohms load without requiring any off-chip components. The integrated transmitter, which incorporates the proposed baseband unit and the RF front end, was fabricated in 130 nm CMOS technology. The transmitter RFIC was directly attached to the system RF PCB using the Chip-on-Board packaging option. The First-Pass success of the system was ensured by paying particular attention to Signal/Power Integrity issues and following an IC-Package-PCB co-design procedure. The transmitter was measured up to 1.5 Gbps, which, to the author’s knowledge, was the highest speed amongst the competitive Multi-Band Impulse-Radio UWB implementations in the literature. The corresponding energy efficiency was 21 pJoule/bit and the Error Vector Magnitude (EVM) 5.5%, while the proposed transmitter improved the spectral sidelobes by over 10 dB. Exploiting the reconfigurability of the transmitter, this thesis presents the first measurements at multi-Mbps speeds that completely meet the final version of the European spectrum emission mask.