<p>Den här högskoleavhandlingen beskriver framtagningen av en modell för en kombinerad styr- och mätutrustning. Syftet med utrustningen är att använda denna för att underlätta vidare utveckling av organisk elektronik vilket är ett av Acreo AB:s forskningsområden. Istället för att till varje ny komponent eller system utveckla ett nytt testsystem kan denna modell användas på ett generellt sätt, vilket sparar värdefull utvecklingstid. I avhandlingen presenteras först de krav som utrustningen ska uppfylla följt av några förslag på lösningar. Därefter väljs ett av förslagen och en grundläggande implementering genomförs med hänsyn mot kraven. Slutligen innehåller rapporten förslag på hur vidare arbete med modellen kan ske.</p> / <p>This bachelor thesis describes the developing of a model for combined steering and measuring equipment. The purpose is to ease further developing of organic electronics, which is one of Acreo AB’s research areas. A test system is needed for every new component or system developed. Instead of constructing a new test environment for every case this equipment will be a general solution that will save valuable developing time. This thesis will first present the requirements followed by some proposal solutions. Thereafter one proposal will be chosen and an essential implementation will be done with consideration of the requirements. Finally the thesis contains suggestions on how to further develop the model.</p>

<p>In this report a transistor-level design of a GHz Sigma-Delta analog-to-digital converter for an RF front end is proposed. The design is current driven, where the integration is done directly over two capacitances and it contains no operational amplifiers.</p><p>The clock frequency used for verification was 2.5 GHz and the output band-width was 10 MHz. The system is flexible in that the number of internal bits can be scaled easily and in this report a three-bit system yielding an SNR of 76.5 dB as well as a four-bit system yielding an SNR of 82.5 dB are analyzed.</p>

Delta-sigma analog-to-digital converters traditionally have been used for low speed, high resolution applications such as measurements, sensors, voice and audio systems. Through continued device scaling in CMOS technology and architectural and circuit level design innovations, they have even become popular for wideband, high dynamic range applications such as wired and wireless communication systems. Therefore, power efficient wideband low power delta-sigma data converters that bridges analog and digital have become mandatory for popular mobile applications today. In this dissertation, two architectural innovations and a development and realization of a state-of-the-art delta-sigma analog to digital converter with effective design techniques in both architectural and circuit levels are presented. The first one is timing-relaxed double noise coupling which effectively provides 2nd order noise shaping in the noise transfer function and overcomes stringent timing requirement for quantization and DEM. The second one presented is a noise shaping SAR quantizer, which provides one order of noise shaping in the noise transfer function. It uses a charge redistribution SAR quantizer and is applied to a timing-relaxed lowdistortion delta-sigma modulator which is suitable for adopting SAR quantizer. Finally a cascade switched capacitor delta-sigma analog-to-digital converter suitable for WLAN applications is presented. It uses a noise folding free double sampling technique and an improved low-distortion architecture with an embedded-adder integrator. The prototype chip is fabricated with a double poly, 4 metal, 0.18μm CMOS process. The measurement result achieves 73.8 dB SNDR over 10 MHz bandwidth. The figure of merit defined by FoM = P/(2 x BW x 2[superscript ENOB]) is 0.27 pJ/conv-step. The measurement results indicate that the proposed design ideas are effective and useful for wideband, low power delta-sigma analog-to-digital converters with low oversampling ratio. / Graduation date: 2012 / Access restricted to the OSU Community at author's request from June 19, 2012 - June 19, 2013

High-speed serial input-output (I/O) link has required advanced equalization and modulation techniques to mitigate inter-symbol interference (ISI) caused by multi-Gb/s signaling over band-limited channels. Increasing demands for transceiver power and area complexity has leveraged on-going interest in analog-to-digital converter (ADC) based link, which allows for robust equalization and flexible adaptation to advanced signaling. With diverse options in ISI control techniques, link performance analysis for complicated transceiver architectures is very important. This work presents advanced statistical modeling for ADC-based link, performance comparison of existing modulation and equalization techniques, and proposed hybrid ADC-based receiver that achieves further power saving in digital equalization. Statistical analysis precisely estimates high-speed link margins at given implementation constrains and low target bit-error-rate (BER), typically ranges from 1e-12 to 1e-15, by applying proper statistical bound of noise and distortion. The proposed statistical ADC-based link modeling utilizes bounded probability density function (PDF) of limited quantization distortion (4-6 bits) through digital feed-forward and decision feedback equalizers (FFE-DFE) to improve low target BER estimation. Based on statistical modeling, this work surveys the impact of insufficient equalization, jitter and crosstalk on modulation selection among two and four level pulse amplitude modulation (PAM-2 and PAM-4, respectively) and duobinary, and ADC resolution reduction performance by partial analog equalizer (PAE). While the information of channel loss at effective Nyquist frequency and signaling constellation loss initially guides modulation selection, the statistical analysis results show that PAM-4 best tolerates jitter and crosstalk, and duobinary requires the least equalization complexity. Meanwhile, despite robust digital equalization, high-speed ADC complexity and power consumption is still a critical bottleneck, so that PAE is necessitated to reduce ADC resolution requirement. Statistical analysis presents up to 8-bit resolution is required in 12.5Gb/s data communications at 46dB of channel loss without PAE, while 5-bit ADC is enough with 3-tap FFE PAE. For optimal ADC resolution reduction by PAE, digital equalizer complexity also increases to provide enough margin tolerating significant quantization distortion. The proposed hybrid receiver defines unreliable signal thresholds by statistical analysis and selectively takes additional digital equalization to save potentially increasing dynamic power consumption in digital. Simulation results report that the hybrid receiver saves at least 64% of digital equalization power with 3-tap FFE PAE in 12.5Gb/s data rate and up to 46dB loss channels. Finally, this work shows the use of embedded-DFE ADC in the hybrid receiver is limited by error propagation.

Denna avhandling behandlar analog-digitalomvandling. I synnerhet behandlas postkorrektion av analog-digitalomvandlare (A/D-omvandlare). A/D-omvandlare är i praktiken behäftade med vissa fel som i sin tur ger upphov till distorsion i omvandlarens utsignal. Om felen har ett systematiskt samband med utsignalen kan de avhjälpas genom att korrigera utsignalen i efterhand. Detta verk behandlar den form av postkorrektion som implementeras med hjälp av en tabell ur vilken korrektionsvärden hämtas. Innan en A/D-omvandlare kan korrigeras måste felen i den mätas upp. Detta görs genom att estimera omvandlarens överföringsfunktion. I detta arbete behandlas speciellt problemet att skatta kvantiseringsintervallens mittpunkter. Det antas härvid att en referenssignal finns tillgänglig som grund för skattningen. En skattare som baseras på sorterade data visas vara bättre än den vanligtvis använda skattaren baserad på sampelmedelvärde. Nästa huvudbidrag visar hur resultatet efter korrigering av en A/D-omvandlare kan predikteras. Omvandlaren antas här ha en viss differentiell olinjäritet och insignalen antas påverkad av ett slumpmässigt brus. Ett postkorrektionssystem, implementerat med begränsad precision, korrigerar utsignalen från A/D-omvandlaren. Ett utryck härleds som beskriver signal-brusförhållandet efter postkorrektion. Förhållandet visar sig bero på den differentiella olinjäritetens varians, det slumpmässiga brusets varians, omvandlarens upplösning samt precisionen med vilken korrektionstermerna beskrivs. Till sist behandlas indexering av korrektionstabeller. Valet av metod för att indexera en korrektionstabell påverkar såväl tabellens storlek som förmågan att beskriva och korrigera dynamiska fel. I avhandlingen behandlas i synnerhet tillståndsmodellbaserade metoder, det vill säga metoder där tabellindex bildas som en funktion utav flera på varandra följande sampel. Allmänt gäller att ju fler sampel som används för att bilda ett tabellindex, desto större blir tabellen, samtidigt som förmågan att beskriva dynamiska fel ökar. En indexeringsmetod som endast använder en delmängd av bitarna i varje sampel föreslås här. Vidare så påvisas hur valet av indexeringsbitar kan göras optimalt, och experimentella utvärderingar åskådliggör att tabellstorleken kan reduceras avsevärt utan att fördenskull minska prestanda mer än marginellt. De teorier och resultat som framförs här har utvärderats med experimentella A/D-omvandlardata eller genom datorsimuleringar. / Analog-to-digital conversion and quantization constitute the topic of this thesis. Post-correction of analog-to-digital converters (ADCs) is considered in particular. ADCs usually exhibit non-ideal behavior in practice. These non-idealities spawn distortions in the converters output. Whenever the errors are systematic, it is possible to mitigate them by mapping the output into a corrected value. The work herein is focused on problems associated with post-correction using look-up tables. All results presented are supported by experiments or simulations. The first problem considered is characterization of the ADC. This is in fact an estimation problem, where the transfer function of the converter should be determined. This thesis deals with estimation of quantization region midpoints, aided by a reference signal. A novel estimator based on order statistics is proposed, and is shown to have superior performance compared with the sample mean traditionally used. The second major area deals with predicting the performance of an ADC after post-correction. A converter with static differential nonlinearities and random input noise is considered. A post-correction is applied, but with limited (fixed-point) resolution in the corrected values. An expression for the signal-to-noise and distortion ratio after post-correction is provided. It is shown that the performance is dependent on the variance of the differential nonlinearity, the variance of the random noise, the resolution of the converter and the precision of the correction values. Finally, the problem of addressing, or indexing, the correction look-up table is dealt with. The indexing method determines both the memory requirements of the table and the ability to describe and correct dynamically dependent error effects. The work here is devoted to state-space--type indexing schemes, which determine the index from a number of consecutive samples. There is a tradeoff between table size and dynamics: more samples used for indexing gives a higher dependence on dynamic, but also a larger table. An indexing scheme that uses only a subset of the bits in each sample is proposed. It is shown how the selection of bits can be optimized, and the exemplary results show that a substantial reduction in memory size is possible with only marginal reduction of performance. / QC 20101019

This thesis strives to enhance the performance of delta-sigma modulators in two areas: increasing their speed and enabling their operation in a low voltage environment. Parallelism based on time-interleaving can be used to increase the speed of delta-sigma modulators. A novel single-path time-interleaved architecture is derived and analyzed. Finite opamp gain and bandwidth result in a mismatch between the noise transfer functions of the internal quantizers which degrades the performance of the new modulator. Two techniques are presented to mitigate the mismatch problem: a hybrid topology where the first stage uses multiple integrators while the rest of the modulator uses a single path of integrators and a digital calibration method. The input-feedforward technique removes the input-signal component from the internal nodes of delta-sigma modulators. The removal of the signal component reduces the signal swing and distortion requirements for the opamps. These characteristics enable the reliable implementation of delta-sigma modulators in modern CMOS technology. Two implementation issues for modulators with input-feedforward are considered. First, the drawback of the analog adder at the quantizer input is identified and the capacitive input feedforward technique is introduced to eliminate the adder. Second, the double sampled input technique is proposed to remove the critical path generate by the input feedforward path. Novel input-feedforward delta-sigma architecture is proposed. The new digital input feedforward (DIFF) modulator maintains the low swing and low distortion requirements of the input feedforward technique, it eliminates the analog adder at the quantizer input, and it improves the achievable resolution. To demonstrate these advantages, a configurable delta-sigma modulator which can operate as a feedback topology or in DIFF mode is implemented in 0.18μm CMOS technology. Both modulators operate at 20MHz clock with an oversampling ratio of 8. The power consumption in the DIFF mode is 22mW and in feedback mode is 19mW. However, the DIFF mode achieves a peak SNDR of 73.7dB (77.1dB peak SNR) while the feedback mode achieves a peak SNDR of 64.3dB (65.9dB peak SNR). Therefore, the energy required per conversion step for the DIFF architecture (2.2 pJ/step) is less than half of that required by the feedback architecture (5.7 pJ/step).

The aim and goal of this work has been to design and implement a voltage reference network for a 12-bit PSAADC, Parallell Successive Analog to Digital Converter. A chip containing the design has been sent away for fabrication. Because of the long processing time, no measurement data are presented. The main specifications for the voltage reference generator is to generate stable reference voltages with low noise and a good PSRR. Efforts has also been made to minimize the power consumption.

The miniaturization and digitization of modern microelectronic systems have made Analog-to-Digital converters (ADC) key building components in many applications. Internet and entertainment technologies demand higher and higher performance from the hardware components in many communication and multimedia systems, but at the same time increased mobility demands less and less power consumption. Many applications, such as instrumentation, video, radar and communications, require very high accuracy and speed and with resolutions up to 16 bits and sampling rates in the 100s of MHz, pipelined ADCs are very suitable for such purposes. Resolutions above 10 bits often require very high power consumption and silicon area if no error correction technique is employed. Calibration relaxes the accuracy requirement of the individual building blocks of the ADC and enables power and area savings. Digital calibration is preferred over analog calibration due to higher robustness and accuracy. Furthermore, the microprocessors that process the digital information from the ADCs have constantly reduced cost and power consumption and improved performance due to technology scaling and innovative microprocessor architectures. The work in this dissertation presents a novel digital background calibration technique for high-speed, high-resolution pipelined ADCs. The technique is implemented in a 14 bit, 100 MS/s pipelined ADC fabricated in Taiwan Semiconductor Manufacturing Company (TSMC) 0.13µm Complementary Metal Oxide Semiconductor (CMOS) digital technology. The prototype ADC achieves better than 11.5 bits linearity at 100 MS/s and achieves a best-in-class figure of merit of 360 fJ/conversion-step. The core ADC has a power consumption of 105 mW and occupies an active area of 1.25 mm^2. The work in this dissertation also presents a low-power, 8-bit algorithmic ADC. This ADC reduces power consumption at system level by minimizing voltage reference generation and ADC input capacitance. This ADC is implemented in International Business Machines Corporation (IBM) 90nm digital CMOS technology and achieves around 7.5 bits linearity at 0.25 MS/s with a power consumption of 300 µW and an active area of 0.27 mm^2.

This thesis strives to enhance the performance of delta-sigma modulators in two areas: increasing their speed and enabling their operation in a low voltage environment. Parallelism based on time-interleaving can be used to increase the speed of delta-sigma modulators. A novel single-path time-interleaved architecture is derived and analyzed. Finite opamp gain and bandwidth result in a mismatch between the noise transfer functions of the internal quantizers which degrades the performance of the new modulator. Two techniques are presented to mitigate the mismatch problem: a hybrid topology where the first stage uses multiple integrators while the rest of the modulator uses a single path of integrators and a digital calibration method. The input-feedforward technique removes the input-signal component from the internal nodes of delta-sigma modulators. The removal of the signal component reduces the signal swing and distortion requirements for the opamps. These characteristics enable the reliable implementation of delta-sigma modulators in modern CMOS technology. Two implementation issues for modulators with input-feedforward are considered. First, the drawback of the analog adder at the quantizer input is identified and the capacitive input feedforward technique is introduced to eliminate the adder. Second, the double sampled input technique is proposed to remove the critical path generate by the input feedforward path. Novel input-feedforward delta-sigma architecture is proposed. The new digital input feedforward (DIFF) modulator maintains the low swing and low distortion requirements of the input feedforward technique, it eliminates the analog adder at the quantizer input, and it improves the achievable resolution. To demonstrate these advantages, a configurable delta-sigma modulator which can operate as a feedback topology or in DIFF mode is implemented in 0.18μm CMOS technology. Both modulators operate at 20MHz clock with an oversampling ratio of 8. The power consumption in the DIFF mode is 22mW and in feedback mode is 19mW. However, the DIFF mode achieves a peak SNDR of 73.7dB (77.1dB peak SNR) while the feedback mode achieves a peak SNDR of 64.3dB (65.9dB peak SNR). Therefore, the energy required per conversion step for the DIFF architecture (2.2 pJ/step) is less than half of that required by the feedback architecture (5.7 pJ/step).

In an industrial and consumer electronic marketplace that is increasingly demanding greater real-world interactivity in portable and distributed devices, analog to digital converter efficiency and performance is being carefully examined. The successive approximation (SAR) analog to digital converter (ADC) architecture has become popular for its high efficiency at mid-speed and resolution requirements. This is due to the one core single bit quantizer, lack of residue amplification, and large digital domain processing allowing for easy process scaling. This work examines the traditional binary capacitive SAR ADC time and statistical information and proposes new structures that optimize ADC performance. The Ternary SAR (TSAR) uses the quantizer delay information to enhance accuracy, speed and power consumption of the overall SAR while providing multi-level redundancy. The early reset merged capacitor switching SAR (EMCS) identifies lost information in the SAR subtraction and optimizes a full binary quanitzer structure for a Ternary MCS DAC. Residue Shaping is demonstrated in SAR and pipeline configurations to allow for an extra bit of signal to noise quantization ratio (SQNR) due to multi-level redundancy. The feedback initialized ternary SAR (FITSAR) is proposed which splits a TSAR into separate binary and ternary sub-ADC structures for speed and power benefits with an inter-stage encoding that not only maintains residue shaping across the binary SAR, but allows for nearly optimally minimal energy consumption for capacitive ternary DACs. Finally, the ternary SAR ideas are applied to R2R DACs to reduce power consumption. These ideas are tested both in simulation and with prototype results. / Graduation date: 2013 / Access restricted to the OSU Community at author's request from Jan. 7, 2013 - Jan. 7, 2014