En muchas áreas citrícolas del mundo el piojo rojo de California (PRC), Aonidiella aurantii (Hemiptera: Diaspididae), está considerado una plaga clave. En el Este de España se ha extendido durante las últimas décadas hasta cubrir una amplia extensión de cítricos. El control químico es difícil y frecuentemente es seguido de infestaciones recurrentes en poco tiempo, de la aparición de resistencias a diferentes productos usados para su control y de la eliminación de enemigos naturales en el campo. La mejora del manejo integrado y las técnicas de control biológico del PRC requieren conocer la composición de los enemigos naturales en cada zona climática, la fluctuación en su abundancia estacional, los niveles de parasitismo y depredación, como se distribuyen en la planta y como son afectados por el clima y el cambio climático. Aunque mucho se ha estudiado en laboratorio sobre los parasitoides Aphytis (Hymenoptera: Aphelinidae), los principales agentes de control del PRC, todavía no se conoce qué combinación de enemigos naturales consigue el mejor nivel de control en el campo, cómo varían los niveles de parasitismo a lo largo del año o cómo los parasitoides se distribuyen y compiten en el campo en relación con el clima. La acción de los Aphytis, ectoparasitoides, es complementada en muchas zonas citrícolas por los endoparasitoides Comperiella bifasciata y Encarsia perniciosi (Hymenoptera: Aphelinidae), los cuales pueden parasitar estadíos diferentes a Aphytis. Muy poco se sabe sobre el comportamiento y las respuestas biológicas bajo diferentes condiciones climáticas de estos endoparasitoides. Del mismo modo, el efecto de los depredadores sobre la población del piojo ha sido raramente estudiado. Actualmente, A. melinus, una especie introducida en el Este de España y el competidor superior, ha desplazado al parasitoide nativo A. chrysomphali de las zonas cálidas y secas ya que puede tolerar mejor las temperaturas cálidas del verano. / Sorribas Mellado, JJ. (2011). Biological control of California red scale, Aonidiella aurantii (Hemiptera: Diaspididae): spatial and temporal distribution of natural enemies, parasitism levels and climate effects [Tesis doctoral]. Universitat Politècnica de València. https://doi.org/10.4995/Thesis/10251/14794

Rezensiert wird das Werk: Alexis Fritz, Christoph Mandry, Ingo Proft, Joseph Schuster, Hrsg., 2021. Digitalisierung im Gesundheitswesen: Anthropologische und ethische Herausforderungen der Mensch-Maschine-Interaktion. Freiburg i. Br.: Herder. Jahrbuch für Moraltheologie. Band. 5. ISBN 978-3451387647.

The shortage of specialist Physics teachers in senior secondary schools in Swaziland has, for years, been one of the nagging issues for the Ministry of Education and Training (MoET). This led MoET to exploiting the services of non-specialists, thus undermining the quality of learners who graduate from the system. Therefore, the study ascertained the causes of the shortage of specialist Physics teachers in senior secondary schools in Swaziland, how they could be retained and how their number could be increased. A positivist-interpretive quantitative research approach was utilised to obtain reliable and valid results in this study. The quantitative research was a survey consisting of a questionnaire that was completed by Physics teachers in senior secondary schools. The data were analysed using descriptive statistics. The study, based on the findings, concluded with some recommendations that could be used to retain and increase the number of Physics teachers in senior secondary schools. / Curriculum and Instructional Studies / M. Ed. (Curriculum Studies)

The populations of three–spined sticklebacks (Gasterosteus aculeatus) in the Baltic Sea have increased tenfold over the last decade. A large increase in abundance can alter the offshore and coastal food webs. Despite of these facts, there are large gaps in the knowledge about the stickleback ecology in the Baltic and the possible effect they might have on their environment. Earlier investigations state that stickleback mainly occupy the deeper areas offshore, and only migrate to the shallow areas during May–July to spawn. Observations by recreational fishermen indicate that this may be incorrect, and that some adult sticklebacks are present in the shallow areas even during the winter. One aim of this study was to investigate the timing of stickleback migration to a shallow coastal area in Kalmar Sound. The study also aimed to examine the relative abundance in two adjacent shallow areas in the archipelago south of Kalmar, where one of the areas is a pike spawning ground. A one month long test fishing with fyke nets was started on the first day after ice break. Results show that the sticklebacks are present in the bays immediately after the ice break, and that high abundances coincide with the pike spawning period. Stomach analyses showed that sticklebacks consumed a large proportion of crustaceans, but also fish eggs were found. These results shed new light on the management actions for many of the coastal spring spawning fish species that have shown decreasing abundances during the last decades. / Bestånden av storspigg (Gasterosteus aculeatus) i Östersjön har ökat markant, data visar på en tiofaldig ökning under det senaste decenniet. Ökningen kan medföra att bl.a. näringsväven, till havs och längs kusterna förändras. Trots vetskapen om detta finns det kunskapsluckor kring spiggens ekologi och dess möjliga påverkan på sin omgivning. Litteratur säger att spiggen till största del bara befinner sig inne längs kusterna under maj-juli. Observationer från sportfiskare tyder på att detta inte stämmer, och att vuxen storspigg befinner sig inne längs kusten och i skärgårdsvikar året om. Ett syfte med studien var att undersöka när spiggen kom in till de grunda vikarna i Kalmarsund. Studien jämförde även spiggtätheterna mellan två närliggande områden där den största skillnaden var födan. Ett månadslångt provfiske inleddes den första isfria dagen i två skyddade vikar söder om Kalmar, där en av lokalerna var en dokumenterad leklokal för gäddor. Resultaten visade att spiggen fanns i vikarna direkt efter islossningen, och vid fisket sammanföll de största spiggfångsterna med gäddleken. Maganalyser visade att en stor andel av födan bestod av olika kräftdjur, men även romkorn hittades. Resultaten tyder på andra förutsättningar för många av de hårt ansatta vårlekande fiskarterna än vad som tidigare är dokumenterat.

近幾年來，雲端應用已是非常普遍現象，雲端計算是推動巨量資料( Big Data)分析與與開放資料界面等關鍵服務之營運模式，同時在近來熱門話題如物聯網、智慧城市、工業4.0等扮演著重要角色。 本文研究目的係探討台灣傳統機械業製造廠使用雲端服務的狀況及如何運用雲端服務創造效益；本研究是以F公司為研究個案，研究個案如何透過雲端應用增加企業效益、顧客滿意度,在當前環境下如何以擬訂之策略增加競爭對手門檻及產品區隔市場，並符合現在趨勢，以迎接工業4.0雛型做準備。 本研究透過個案資料收集、相關文獻探討及個案執行人員訪談，探討雲端服務在傳統製造業為公司經營所創造之效益。本研究從「傳統機械業遇到的挑戰與策略」、「個案F公司背景及營運現況(公司、產品、顧客)」、「雲端計算的應用」、「傳統機械業加上雲端應用後的效益」四個面向切入探討。 研究發現，傳統機械業在雲端應用的利益，不僅可以成為公司銷售策略、提升現有服務的品質更能以創新服務協助企業做節能診斷與建議，這樣不僅替客戶節省成本，並且增進顧客滿意度及黏著度。而另一個發現是透過雲端應用，可進一步作供應鏈管理，減少企業備料時間及降低庫存，使企業在激烈的競爭環境中，降低成本、增加毛利並創造企業長期的競爭優勢，同時為未來工業4.0之引進做準備。 關鍵字:雲端應用、傳統機械業、增加企業效益、 創新服務、增進顧客滿意度、 工業4.0. / Cloud applications have become prevalent in recent years. In particular, cloud computing is the operational model in key services for promoting big data analysis and open data interface. It also plays the vital roles in recent popular subjects, such as the internet of things, smart city, and industry 4.0. The objective of this study is to explore the current conditions of how cloud services are utilized in the traditional machine factories in Taiwan and to create benefits. With Company F as the case, this study examines how cloud applications are used to improve corporate benefits and customer satisfaction, as well as how strategies should be formulated for market differentiation to increase competitiveness, connect with current trends, and prepare for the prototype of industry 4.0. Through data collection, literary review, and interview with project implementation staff of the case, the study explores the benefits that cloud applications generate for the traditional manufacturing businesses. There are four focuses of investigation in this study—challenges encountered and strategies formulated by the traditional mechanical industry; case study of company F, including company background and the existing operation concerning the company, product and customers; applications of cloud computing; benefits of cloud applications on traditional mechanical industry. It is indicated in research findings that in the traditional mechanical industry, the benefits of cloud computing will not only become corporate sales strategy and improve existing service quality, but also provide diagnosis and recommendations on energy saving for corporations with innovative services. This will help clients cut costs, and improve customer satisfaction and adhesion. An additional finding is that cloud applications can further manage the supply chain, minimize lead time, and reduce inventory, which enable corporations to reduce costs, increase gross profits, and create long term corporate advantages in a competitive environment to prepare for the upcoming industry 4.0. Keywords: Cloud applications, traditional mechanical industry, improve corporate benefit, innovative service, increase customer satisfaction, industry 4.0.

The shortage of specialist Physics teachers in senior secondary schools in Swaziland has, for years, been one of the nagging issues for the Ministry of Education and Training (MoET). This led MoET to exploiting the services of non-specialists, thus undermining the quality of learners who graduate from the system. Therefore, the study ascertained the causes of the shortage of specialist Physics teachers in senior secondary schools in Swaziland, how they could be retained and how their number could be increased. A positivist-interpretive quantitative research approach was utilised to obtain reliable and valid results in this study. The quantitative research was a survey consisting of a questionnaire that was completed by Physics teachers in senior secondary schools. The data were analysed using descriptive statistics. The study, based on the findings, concluded with some recommendations that could be used to retain and increase the number of Physics teachers in senior secondary schools. / Curriculum and Instructional Studies / M. Ed. (Curriculum Studies)

Die Anwendungsmöglichkeiten und Potenziale des temperierten Innenhochdruck-Umformens mit flüssigen Wirkmedien (T-IHU) von Rohren aus verschiedenen Magnesium- und Aluminiumknetlegierungen werden in der vorliegenden Arbeit aufgezeigt. Neben der Werkstoff- und Halbzeugcharakterisierung, der Auslegung von temperierten Innenhochdruck-Umformanlagen und –werkzeugen, den Thermografiemessungen am Halbzeug unter Realbedingungen und der Verifizierung der Simulationsergebnisse des T-IHU-Werkzeuges war der inhaltliche Schwerpunkt die systematische experimentelle Bestimmung der maximalen Umfangserweiterung ∆u_max in Anhängigkeit von der Umformtemperatur ϑ_u, dem Werkstoff und der Wanddicke s₀ im Temperaturbereich von 22°C bis 300°C an drei Versuchsgeometrien T-Stück, Zylinder und Quader bei Innendrücken bis 800 bar. Neben dem Einfluss der Prozessparameter, der Werkstoff- und Halbzeugeigenschaften und der Ausgangswanddicke wurde der signifikante Einfluss der Umformtemperatur und der Umformgeometrie auf die erreichbaren Umfangserweiterungen herausgearbeitet und systematisch dargestellt. Es wurden Umfangsdehnungen von bis zu 120 % (bei ϑ_u = 300°C) erzielt. Die experimentelle Bestimmung der minimal auszuformenden Bauteilaußenradien erfolgte unter Anwendung der statistischen Versuchsplanung. Aus den Regressionsgleichungen wurde eine neue Berechnungsgleichung für den maximalen Innendruck p_imax generiert. Durch die Verifikation dieser Gleichung konnte die hohe Genauigkeit bei der Vorausberechnung des erforderlichen Innendruckes bei einem vorgegebenen minimalen Bauteilaußenradius R_min in Abhängigkeit von der Zugfestigkeit R_m als f (Umformtemperatur) und der Wanddicke s₀ nachgewiesen werden. Die Auslegung der T-IHU-Werkzeug- und Anlagentechnik kann damit wesentlich genauer er­folgen. Durch die Bauteilanalysen nach dem T-IHU-Prozess konnten die hohe Maß- und Formgenauigkeit und die hohe und gleichmäßigere Oberflächengüte nachgewiesen werden. Trotz der beginnenden dynamischen Rekristallisation lag bei allen Versuchswerkstoffen eine Erhöhung der Werkstofffestigkeit in der Umformzone vor. Bei den Untersuchungen bzgl. des T-IHU des Realbauteiles „PKW-Querträger vorn“ konnten die Kenntnisse der Grundlagenuntersuchungen auf ein komplex geformtes Realteil übertragen und erweitert werden. Es zeigte sich, dass der Einsatz von T-IHU-Magnesiumbauteilen ein erhebliches Potenzial für weitere Gewichtsreduzierungen von Leichtbaukonstruktionen besitzt. / This paper presents the potential applications of temperature-supported hydroforming of various magnesium and aluminium alloy tubes using active liquid media. It includes details of material and semi-finished product characterisation, the design of temperature-supported hydroforming equipment and tools, thermography measurements on the semi-finished product under real conditions and verification of simulation results for the temperature-supported hydroforming tool. The main focus, however, was the systematic, experimental approach to determining the maximum increase in perimeter ∆u_max as a function of the forming temperature ϑ_u, the material and the wall thickness s₀ in the temperature range 22°C to 300°C for three trial geometries (T‑piece, cylinder and cuboid) at internal pressures of up to 800 bar. In addition to studying the effect of process parameters, material properties, semi-finished product characteristics and initial wall thickness, the paper also presents the finding that forming temperature and forming geometry have a significant impact on achievable increases in perimeter. Perimeter expansions of up to 120 % were attained (at ϑ_u = 300°C). Statistically designed experiments were used to determine the minimum component outside-radii to undergo the forming process. A new equation for calculating the maximum internal pressure p_imax was generated from regression equations. By verifying this equation, it was possible to demonstrate the high level of accuracy in predicting the internal pressure required for a given minimum component outside-radius R_min as a function of the tensile strength R_m as f(forming temperature) and of the wall thickness s₀. This means that the temperature-supported hydroforming tool and system equipment can be designed far more accurately. Component analyses after the temperature-supported hydroforming process demonstrated the high level of dimensional and geometrical accuracy and the high quality and more consistent surface finish. Despite the onset of dynamic re-crystallisation, the strength of the material was increased in the forming zone in all the materials tested. The knowledge gained from researching the fundamental principles was applied to a real component with a complex shape in studies of temperature-supported hydroforming of the "front car cross-member", which provided further useful insights. It was found that the use of temperature-supported hydroforming magnesium components has considerable potential for further weight reduction in lightweight constructions.

Chemical EOR processes such as polymer flooding and surfactant polymer flooding must be designed and implemented in an economically attractive manner to be perceived as viable oil recovery options. The primary expenses associated with these processes are chemical costs which are predominantly controlled by the crude oil properties of a reservoir. Crude oil viscosity dictates polymer concentration requirements for mobility control and can also negatively affect the rheological properties of a microemulsion when surfactant polymer flooding. High microemulsion viscosity can be reduced with the introduction of an alcohol co-solvent into the surfactant formulation, but this increases the cost of the formulation. Experimental research done as part of this study combined the process of hot water injection with ASP flooding as a solution to reduce both crude oil viscosity and microemulsion viscosity. The results of this investigation revealed that when action was taken to reduce microemulsion viscosity, residual oil recoveries were greater than 90%. Hot water flooding lowered required polymer concentrations by reducing oil viscosity and lowered microemulsion viscosity without co-solvent. Laboratory testing of viscous microemulsions in core floods proved to compromise surfactant performance and oil recovery by causing high surfactant retention, high pressure gradients that would be unsustainable in the field, high required polymer concentrations to maintain favorable mobility during chemical flooding, reduced sweep efficiency and stagnation of microemulsions due to high viscosity from flowing at low shear rates. Rough scale-up chemical cost estimations were performed using core flood performance data. Without reducing microemulsion viscosity, field chemical costs were as high as 26.15 dollars per incremental barrel of oil. The introduction of co-solvent reduced chemical costs to as low as 22.01 dollars per incremental barrel of oil. This reduction in cost is the combined result of increasing residual oil recovery and the added cost of an alcohol co-solvent. Heating the reservoir by hot water flooding resulted in combined chemical and heating costs of 13.94 dollars per incremental barrel of oil. The significant drop in cost when using hot water is due to increased residual oil recovery, reduction in polymer concentrations from reduced oil viscosity and reduction of microemulsion viscosity at a fraction of the cost of co-solvent. / text

Heavy oil production depends on the understanding of mechanical and flow properties of unconsolidated or weakly consolidated sands under different loading paths and boundary conditions. Reconstituted bitumen-free Athabasca oil-sands samples were used to investigate the geomechanics of a steam injection process such as the Steam Assisted Gravity Drainage (SAGD). Four stress paths have been studied in this work: triaxial compression, radial extension, pore pressure increase and isotropic compression. Absolute permeability, end-point relative permeability to oil & water (kro and krw), initial water saturation and residual oil saturation were measured while the samples deformed. Triaxial compression is a stress path of increasing mean stress while radial extension and pore pressure increase lead to decreasing mean stress. Pore pressure increase experiments were carried out for three initial states: equal axial and confining stresses, axial stress greater than confining stress and confining stress greater than axial stress. Pore pressure was increased under four boundary conditions: 1) constant axial and confining stress; 2) constant axial stress and zero radial strain; 3) zero axial strain and constant confining stress; and 4) zero axial and radial strain. These experiments were designed to mimic geologic conditions where vertical stress was either S1 or S3, the lateral boundary conditions were either zero strain or constant stress, and the vertical boundary conditions were either zero strain or constant stress. Triaxial compression caused a decrease in permeability as the sample compacted, followed by appreciable permeability enhancement during sample dilation. Radial extension led to sample dilation, shear failure and permeability increase from the beginning. The krw and kro increased by 40% and 15% post-compaction respectively for the samples corresponding to lower depths during triaxial compression. For these samples, residual oil saturation decreased by as much as 40%. For radial extension, the permeability enhancement decreased with depth and ranged from 20% to 50% while the residual oil saturation decreased by up to 55%. For both stress paths, more shear-enhanced permeability was observed for samples tested at lower pressures, implying that permeability enhancement is higher for shallower sands. The pore pressure increase experiments showed an increase of only 0-10% in absolute permeability except when the effective stress became close to zero. This could possibly have occurred due to steady state flow not being reached during absolute permeability measurement. The krw curves generally increased as the pore pressure was increased from 0 psi. The increase ranged from 5% to 44% for the different boundary conditions and differential stresses. The kro curves also showed an increasing trend for most of the cases. The residual oil saturation decreased by 40-60% for samples corresponding to shallow depths while it increased by 0-10% for samples corresponding to greater depths. The reservoirs with high differential stress are more conducive to favorable changes in permeability and residual oil saturation. These results suggested that a decreasing mean stress path is more beneficial for production increase than an increasing mean stress path. The unconsolidated sands are over-consolidated because of previous ice loading which makes the sand matrix stiffer. In this work, it was found that over-consolidation, as expected, decreased the porosity and permeability (40-50%) and increased the Young’s and bulk moduli of the sand. The result is sand which failed at higher than expected stress during triaxial compression. Overall, results show that lab experiments support increased permeability due to steam injection operations in heavy oil, and more importantly, the observed reduction in residual oil saturation implies SAGD induced deformation should improve recovery factors. / text

No description available.