A liquid Cooled below its normal freezing temperature is known as a supercooled liquid. On further cooling, supercooled liquids crystallize to thermodynamically stable, ordered structures. Alternatively, if the cooling rate is fast enough, the crystallization may be avoided altogether. Below a particular temperature during rapid cooling the liquid will solidify into a disordered, amorphous phase -also known as the glassy phase of matter. This particular temperature is termed the ”glass transition temperature” (Tg). Unlike a crystalline solid, a glass is neither a thermodynamically stable phase nor does it possess long range molecular ordering. Very slow structural relaxation (in the time scale of ∼ 100 s) is always present in the glassy phase. Thus, this phase is often referred to as a metastable phase of matter. Experimental and theoretical studies related to the behavior of supercooled liquids are the subject matter of many investigations for the last few decades [1]. These studies find their applications in diverse fields such as geology, cryopreservation, glaciology and atmospheric science. However, properties of supercooled liquids and the corresponding amorphous phase are not completely understood at present, particularly for hydrogen bonded (H-bonded) systems. This thesis concerns both the crystallization and the glass formation process of H-bonded systems. The systems of interest are water, the commonly accepted universal solvent, and the aqueous binary mixture of glycerol and water. The technique of molecular probing is often used to study the cooperativety and rotational diffusion of supercooled liquids and for determination of the glass transition temperature. For the present set of work, a molecular probe technique called spin probe ESR is extensively used. Electron paramagnetic resonance or electron spin resonance (EPR/ESR) measures the electronic energy level separation and is well known for the high sensitivity. All of the systems studied in the present set of work are diamagnetic. This issue is circumvented by dissolving paramagnetic spin probe molecules, which are usually organic free radicals with one N-O group, into the systems. Spin probes are added in very low concentrations (~10-3M) to minimize the effect on the host system and also to avoid mutual interactions between them. The unpaired electron delocalized in the direction of the N-O bond serves as the paramagnetic center required for an ESR experiment. The splitting of electron energy level due to the external magnetic field (Zeeman splitting) can give rise to resonance absorption of energy if exposed to a microwave of appropriate frequency. There is also a magnetic coupling (hyperfine) between the spin of the unpaired electron and nuclear spin of the nearby nitrogen atom. The hyperfine coupling splits each electron energy levels, to the first order, symmetrically into three levels. The transitions between these levels -subject to appropriate selection rules -give rise to the ESR spectrum [2]. The spectral shape in a magnetic field sweep ESR experiment appears complex if randomly oriented spin probes are dispersed in an amorphous or polycrystalline solid matrix. The high degree of mobility in probe molecules, present in a liquid solution, can average out the individual anisotropy of magnetic tensors to get a spectrum of three equally spaced liens. Experiments can be performed spanning a spin probe reorientation timescale of 10-7-10-12 s typically in the temperature range of 4.2 -300K. In chapter one we have given a brief overview of the supercooled liquids and the phase transitions related to the present work. Particular emphasis has been given to the dynamical features of the supercooled liquid close to its glass transition temperature and their classification based on the degree of ’fragility’ [3]. Brief general introductions of the systems studied in each of the following chapters are also provided. Then, the details of ESR spectroscopy and a quantum mechanical picture of the method of spin probe ESR have been discussed [4]. A separate section has been devoted to the numerical and analytical methods used to analyze the spectrum to extract information related to the spin probe dynamics [5]. The chapter concludes with a description of the ESR spectrometer. In chapter two we have studied the glass transition and dynamics of the supercooled water by the method of spin probe ESR. The vitrification has been done by direct exposure of the bulk water sample, doped with the spin probe TEMPOL, to the liquid helium flow. The vitrified matrix turns into the ultraviscous liquid above the putative glass transition temperature of ~136 K which further transforms to cubic ice (Ic) above TX ~150 K. The supercooled fraction of water, along with the spin probes which are treated as impurities by the crystallized surroundings, remain trapped inside the veins or triple junctions of the ice grains which serve as the interfacial reservoir of impurities in a polycrystalline ice matrix. The spectra for the entire temperature range have been analyzed with the help of in-depth computation by modelling the reorientation of TEMPOL in terms of the jump angle θs and the rotational correlation time τ [5]. This model, based on a homogeneous mobility scenario of the spin probe, works nicely except in the temperature range of 140-180 K. Dynamical heterogeneity (DH) is apparent in this temperature range and a more mobile (fast) component, as compared to the one corresponding to the very slow dynamics of TEMPOL at lower temperatures (slow), is observed. The relative weight of the fast and the slow component changes with temperature and above ~180 K the entire spectrum changes into the motionally narrowed triplet. The temperature dependence of the slow component of τ shows a change in slope at a temperature close to the putative glass transition temperature of water. The fast component of τ exhibits a fragile, i.e. non-Arrhenius character at high temperature with a crossover to a strong, i.e. Arrhenius behavior below ~225 K, close to the hypothesized fragile-to-strong crossover (FSC) for water at TFSC ~228 K. The breakdown of the Debye-Stokes-Einstein (DSE) law is observed when the τ values are combined with the available viscosity data of water to evaluate the DSE ratio, paralleling the SE breakdown which has recently been observed in nanoconfined water [6]. The dynamical heterogeneity is thought to be closely associated with the static structural heterogeneities of supercooled water. The existence of large scale structural fluctuations spanning a range of low-and high-density phases of liquid water have been associated with the heterogeneous dynamics sensed by TEMPOL. Motivated by the Arrhenius like behavior of the slow component, it has been identified with the low density liquid (LDL). The fragile nature of the fast component at high temperature may be identified with that of the high density liquid (HDL) which is the predominant fraction in liquid or weakly supercooled water [6]. Chapter three reports the studies on freezing and dynamics of the supercooled water trapped inside the veins of a polycrystalline ice matrix by dissolving spin probes TEMPO and TEMPOL into it. When a millimolar spin probe aqueous solution is cooled below the freezing point of water, the spin probes -driven by the mechanism described above migrate to the liquid environment inside the ice veins. Local concentration of the probe molecules inside the veins can go up to 1-10 M [7]. Bulk crystallization is evident in differential scanning calorimetry (DSC) studies whereas the liquid environment of the spin probe below the bulk freezing is confirmed by its narrow triplet ESR spectrum. A sudden collapse of this narrow triplet into a single broad line indicates the freezing of the trapped water fraction which usually happens well below the DSC freezing point for both the probes. The spin probe detected freezing point of this interstitial water is found to be largely dependent on the properties and the amount of the dissolved probe molecules. An explanation is sought in terms of the ’destructuring effect’ on the tetrahedral ordering of the water H-bond network by both the high local concentration of the spin probes and the hydrogen bond strength, formed between the water and the spin probe molecules through the polar groups of the latter [8, 9]. These two factors are thought to play important roles in determining the reorientational dynamics of the spin probe molecules, as well. The rotational correlation times of the two probes exhibit a crossover owing to the different mobility of their salvation shells in the more ordered supercooled water. The observed relaxation behavior of this confined water using the probe TEMPO, which has little effect on water H-bond network, is found in agreement with the previous experimental investigations on water confined in a nanochannel [10]. In chapter four, the glass transition, relaxation and the free volume of the glycerol-water (G-W) system are studied over the glycerol concentration range of 5 -85 mol% with TEMPO as the spin probe. G-W mixture is intrinsically inhomogeneous due to the well established phase segregation below a critical glycerol concentration of 40 mol%. In the inhomogeneous regime the water molecules tend to form cooperative domains besides the mesoscopic G-W mixture [11]. Samples are quenched by rapid cooling down to 4.2 K inside the spectrometer cryostat. Spectra were recorded on slow heating of the sample in the temperature range of 130 -305 K. The glass transition temperature is correlated to the sharp transition of the extrema separation of the ESR spectrum. The glass transition temperatures are found to follow a concentration dependence which is closely associated to the mesoscopic inhomogeneities of the G-W system. The steady enhancement in fragility of the G-W system with the addition of water is evident from the temperature dependence of the spin probe correlation time τ for the entire concentration range. In the temperature range of 283 -303 K, the DSE law is followed i.e. the spin probe reorientation process is found to be strongly coupled to the system viscosity. In this regime, the τ values have been used along with the available viscosity data to calculate the effective volume V of the spin probe for the entire concentration range. The spin probe effective volume is a measure of the available free volume of the host matrix. A drastic change in the quantity is seen in the vicinity of the 40 mol% glycerol concentration owing to a similar structural change of the matrix due to the formation of mesoscopic scale inhomogeneities below the critical concentration [12]. The thesis concludes with a discussion about the possible future directions of research.

TDO utilizes b-type heme as a cofactor to activate dioxygen and insert two oxygen atoms into free L-tryptophan. We revealed two unidentified enzymatic activities of ferric TDO from Ralstonia metallidurans, which are peroxide driven oxygenation and catalase-like activity. The stoichiometric titration suggests that two moles of H2O2 were required for the production of one mole of N-formylkynurenine. We have also observed monooxygenated-L-tryptophan. Three enzyme-based intermediates were sequentially detected in the peroxide oxidation of ferric TDO in the absence of L-Trp including compound I-type and compound ES-type Fe-oxo species. The Fe(IV) intermediates had an unusually large quadrupole splitting parameter of 1.76(2) mm/s at pH 7.4. Density functional theory calculations suggest that it results from the hydrogen bonding to the oxo group. We have also demonstrated that the oxidized TDO was activated via a homolytic cleavage of the O-O bond of ferric hydroperoxide intermediate via a substrate dependent process to generate a ferrous TDO. We proposed a peroxide activation mechanism of the oxidized TDO. The TDO has a relatively high redox potential, the protonated state of the proximal histidine upon substrate binding as well as a common feature of the formation of ferric hydroxide species upon substrate or substrate analogues binding. Putting these together, we have proposed a substrate-based activation mechanism of the oxidized TDO. Our work also probed the role of histidine 72 as an acid-base catalyst in the active site. In H72S and H72N mutants, one water molecule plays a similar role as that of His72 in wild type TDO. MauG is a c-type di-heme enzyme which catalyze the biosynthesis of the protein-derived cofactor tryptophan tryptophylquinone. Its natural substrate is a monohydroxylated tryptophan residue present in a 119-kDa precursor protein of methylamine dehydrogenase (MADH). We have trapped a novel bis-Fe(IV) intermediate from MauG, which is remarkably stable. A tryptophanyl radical intermediate of MADH has been trapped after the reaction of the substrate with the bis-Fe(IV) intermediate. Analysis by high-resolution size-exclusion chromatography shows that MauG can tightly bind to the biosynthetic precursor and form a stable complex, but the mature protein substrate does not.

In this study, the oxygen-deficient TiO2, SrTiO3 systems and transition metal ion (Cr or V) doped TiO2, SrTiO3 and SrZrO3 systems have been investigated. We prepared samples as polycrystals, single crystals and thin films for various desires. Their structural, physical and electronic properties were measured by bulk-sensitive techniques (X-Ray Diffraction, SQUID and Electro Paramagnetic Resonance) or surface-sensitive techniques (Photoemission spectroscopy and X-ray absorption spectroscopy). The measurement of SQUID and EPR showed not only their magnetic properties but also the valence state of Cr dopant. We verified the valence state of Cr ions in oxides and found the key parameters of sample synthesis which control the valence state of Cr ions. Segregated phases such as SrCrO4 were formed when the samples were synthesized under O2 rich environment. The surface properties of Cr doped SrZrO3 films are also discussed. We found the synthesis conditions which influence on not only the behavior of Cr ions but also the resistive-switching behaviors. Various resistive-switching behaviors seem to depend on the surface chemistry of films. We found that the accumulation of Cr3+ on film surface provides a clean interface without any non-stoichiometric oxides and that this sharp interface termination results in a good performance of resistive-switching.

Perovskite rare-earth manganites of the form R1-xAxMnO3 (R – rare earth ion or Bi, A – Ca,Sr) have drawn an overwhelming research interest during the last few years owing to their extraordinary physical properties. Some of the interesting phenomena exhibited by the manganites are (a) colossal magneotresistance (CMR) (b) charge, orbital and spin ordering and (c) phase separation at nano and micron scale. The manganites are strongly correlated systems in which the charge, spin and orbital degrees of freedom are coupled. The properties of these materials are sensitive functions of external stimuli such as the doping, temperature and pressure [1-5] and have been extensively studied both experimentally and theoretically on single crystal, bulk polycrystalline and thin film forms of the samples [6-9]. Recently attention has been drawn towards the properties of nanoscale manganites. The nanoscale materials are expected to behave quite differently from extended solids due to quantum confinement effects and high surface/volume ratio. Nanoscale CMR manganites have been fabricated using diverse methods in the form of particles, wires, tubes and various other forms by different groups. It has been shown that the properties of CMR manganites can be tuned by reducing the particle size down to nanometer range and by changing the morphology [10-14]. The physical properties of antiferromagnetic insulating charge ordered manganites have been well investigated by using numerous experimental techniques on bulk solids. It is known that the charge ordered (CO) phase is ‘melted’ resulting in a ferromagnetic, metallic phase on application of high magnetic fields, electric fields, impurity ion doping, high energetic ion irradiation and by pressure [15-17]. However, no attempts have been made on the fabrication and the physical property investigations on nanoscale charge ordered manganites. Hence, we have undertaken to study the properties of charge ordered manganites prepared at nanoscale using various experimental probes. In this thesis we present the results on magnetization, magnetotransport and Electron Magnetic Resonance (EMR) (electron paramagnetic resonance in the paramagnetic phase and ferromagnetic resonance in the ferromagnetic phase) studies of the following nanoscale compounds and compare the properties with those of their bulk counterparts; (a) highly robust antiferromagnetic insulating CE –type charge ordered manganite Pr0.5Ca0.5MnO3 (PCMO) (b) highly robust antiferromagnetic insulating CE- type charge ordered manganite Nd0.5Ca0.5MnO3 (NCMO) (c) moderately robust A-type charge ordered manganite Pr0.5Sr0.5MnO3 (PSMO) (d) highly robust insulating anti-ferromagnetic charge ordered manganites Bi0.5Ca0.5MnO3 (BCMO) and Bi0.5Sr0.5MnO3 (BSMO) and (e) a CMR manganite Pr0.7Pb0.3MnO3 (PPMO). Chapter 1 of the thesis contains a brief introduction to the general features of manganites describing various interesting phenomena and the interactions underlying them. Further, we have written a detailed review on the properties of nanometric CMR manganites of various sizes and shapes. In this chapter, we have also described the experimental methodology and the analysis procedure adopted in this work Chapter 2 reports the fabrication of nanowires and nanoparticles of Pr0.5Ca0.5MnO3 (PCMO) and the results obtained from magnetization, magnetotransport and electron magnetic resonance measurements performed on nanoscale PCMO along with their comparison with those of the bulk sample. Here, the nanowires of PCMO were prepared by hydrothermal method and the nanoparticles of mean sizes 10, 20 and 40 nm were prepared by polymer assisted sol-gel method. Solid state reaction method was used to prepare the micron sized PCMO bulk material. Different techniques like XRD, TEM, EDAX and ICPAES have been used to characterize the samples. The novel result of the present investigation is the weakening of charge order and switch over from the anti-ferromagnetic phase to ferromagnetic phase in PCMO nanowires [18]. In addition, the charge order is seem to have completely suppressed in 10 nm PCMO nanoparticles as observed from the magnetization measurements. These results are particularly very significant as one needs magnetic fields of ~ 27 T to melt the charge ordered phase in PCMO. Size induced insulator-metal transition TM-I is observed in nanoscale PCMO at low temperatures accompanied by ferromagnetism. CMR of 99.7% is obtained at TM-I and at a field of 11 T. EMR studies have confirmed the presence of ferromagnetic phase at low temperatures. Temperature dependent EMR line width and intensity have shown the presence of CO phase in PCMO10 though static magnetization measurements have shown the absence of CO phase. It is found that the EMR linewidth increases with the decrease of particle size. Chapter 3 reports the fabrication of nanoparticles of Nd0.5Ca0.5MnO3 (NCMO) and the results obtained from magnetization, magnetotransport and electron magnetic resonance measurements performed on nanoscale NCMO along with their comparison with those of bulk NCMO. The nanoparticles of NCMO of mean sizes 5, 20 and 40 nm were prepared by polymer assisted sol-gel method. Solid state reaction method was used to prepare the micron sized NCMO bulk material. Different techniques like XRD, TEM, EDAX and ICPAES have been used to characterize the samples. A striking result of this particular investigation is the complete suppression of charge ordered phase in 5 and 20 nm NCMO nanoparticles as observed from the magnetization measurements [19]. Size induced insulator-metal transition TM-I is observed in nanoscale NCMO at low temperatures accompanied by ferromagnetism in accordance with Zener double exchange meachanism. CMR of 99.7% is obtained at TM-I and at a field of 11 T. EMR studies have confirmed the presence of ferromagnetic phase at low temperatures. Temperature dependent EMR line width and intensity have shown the presence of residual CO fluctuations in NCMO5 though the static magnetization measurements have shown the absence of CO phase. It is found that the EMR linewidth increases with the decrease of particle size. Low temperature X-ray diffraction measurements on NCMO20 indicate the absence of CO phase. But the preliminary results obtained from the optical spectroscopy measurements indicate the evidence for the presence of CO phase. In Chapter 4, we report the investigations on the nanoscale PSMO. PSMO nanoparticles of sizes 20, 40 and 60 nm are prepared by polymer precursor sol-gel method. PSMO nanowires of diameter 50 nm and lengths of a few microns have been prepared by hydrothermal method. The bulk polycrystalline PSMO is obtained by crushing the single crystal of the same prepared by float zone method. Various techniques like XRD, TEM, VSM, transport measurements and EMR spectroscopy have been employed to characterize and to study the size dependent magnetic, transport and electron magnetic resonance properties and to compare them with those of the bulk. Our results show that there is a disappearance of anti-ferromagnetic charge ordering phase and the appearance of a ferromagnetic phase at low temperatures in all PSMO nanoparticles and nanowires. Metal like behaviour is observed in the size induced ferromagnetic phase in nanoparticles. The EMR linewidth increases with the decrease of particle size. A comparison with the properties of the bulk material shows that the ferromagnetic transition at 265 K remains unaffected but the anti-ferromagnetic transition at TN = 150 K disappears in the nanoparticles. Further, the temperature dependence of magnetic anisotropy shows a complex behaviour, being higher in the nanoparticles at high temperatures, lower at lower temperatures in comparison with the bulk [20]. In Chapter 5, we present the fabrication, characterization and the results obtained from the magnetization and EMR measurements carried out on BCMO and BSMO nanoparticles and compare the results with those of the bulk. X-ray diffraction gives evidence for single phasic nature of the materials as well as their structures. Mono-dispersed to a large extent, isolated nanoparticles are seen in the transmission electron micrographs. High resolution electron microscopy shows the crystalline nature of the nanoparticles. Superconducting quantum interferometer based magnetic measurements from 10 K to 300 K show that these nanomanganites retain the charge ordering nature unlike the Pr and Nd based nanomanganites. The CO in Bi based manganites is thus found to be very robust consistent with the observation that magnetic fields of the order of 130 T are necessary to melt the CO in these compounds. These results are supported by electron magnetic resonance measurements [21]. In Chapter 6, we present our results on the effect of particle size on the magnetic properties of Pr0.7Pb0.3MnO3 (PPMO). PPMO nanoparticles of two different sizes (~5 nm and 30 nm) were prepared by the polymeric precursor sol-gel method. The samples are characterized by different techniques like XRD, TEM, SQUID magnetometry, EMR and optical spectroscopic measurements. It is found that the nanoparticles crystallize in the cubic perovskite structure. TEM measurements show that the 5 nm particles are uniform in size. They are also crystalline as seen by HREM and XRD measurements. SQUID magnetometry measurements have shown that the Curie temperature increases (from 220 K to 235 K) with the increase of particle size. Saturation magnetization is higher for the smaller particles studied. We have observed only one EMR signal down to 4 K in both the nanoparticles (5 and 30 nm) in contrast to the two EMR signal behaviour observed in bulk PPMO [22]. It is found that the EMR linewidth increases with the decrease of particle size in the paramagnetic phase. Temperature dependent optical spectroscopy measurements performed on 5 nm PPMO nanoparticles indicate that the insulator-metal transition temperature TM-I = 230 K, is not very different from TM-I = 235 K of the bulk sample [23] The thesis concludes with a brief writeup summarizing the results and pointing out possible future directions of research in the area.

No description available.

Treatment of the diethyl ester of o-phenylenebis(oxamic acid) (opbaH2Et2, 1) with 5/6 equivalent of MeNH2 in abs. EtOH results in the exclusive formation of the ethyl ester of o-phenylene(N′-methyl oxamide)(oxamic acid) (opooH3EtMe, 2) in ca. 50% yield. Treatment of 2 with four equivalents of [Me4N]OH followed by the addition of Cu(ClO4)2·6H2O gave [Me4N]2[Cu(opooMe)]·H2O (3A) in ca. 80% yield. As 3A appears to be a hygroscopic solid, the related [nBu4N]+ salts [nBu4N]2[M(opooMe)]·H2O (M = Cu (3B), Ni (4)) have been synthesized. By addition of two equivalents of [Cu(pmdta)(NO3)2] to a MeCN solution of 3B the novel asymmetric trinuclear complex [Cu3(opooMe)(pmdta)2](NO3)2 (5) could be obtained in ca. 90% yield. Compounds 2, 3A, 3B, 4 and 5 have been characterized by elemental analysis and NMR/IR spectroscopy. Furthermore, the solid state structures of 3A in the form of [Me4N]2[Cu(opooMe)]·MeOH (3A′), 3B in the form of [nBu4N]2[Cu(opooMe)] (3B′), 4 in the form of [nBu4N]2[Ni(opooMe)]·1.25H2O (4′) and 5 in the form of [Cu3(opooMe)(pmdta)2] (NO3)2·3MeCN (5′), respectively, have been determined by single-crystal X-ray diffraction studies. By controlled cocrystallization, diamagnetically diluted 3B (1%) in the host lattice of 4 (99%) in the form of single crystals have been made available, allowing single crystal EPR studies to extract all components of the g-factor and the tensors of onsite CuA and transferred NA hyperfine interaction. Out of these studies the spin density distribution of the [Cu(opooMe)]2− complex fragment could be determined. The magnetic properties of 5 were studied by susceptibility measurements versus temperature. An intramolecular J parameter of −65 cm−1 has been obtained, unexpectedly, as 5 should possess two different J values due to its two different spacers between the adjacent CuII ions, namely an oxamate (C2NO3) and an oxamidate (C2N2O2) fragment. This unexpected result is explained by a summarizing discussion of the experimentally obtained EPR results (spin density distribution) of 3B, the geometries of the terminal [Cu(pmdta)]2+ fragments of 5 determined by X-ray crystallographic studies and accompanying quantum chemical calculations of the spin density distribution of the mononuclear [Cu(opooMe)]2− and of the magnetic exchange interactions of trinuclear [Cu3(opooMe)(pmdta)2]2+ complex fragments. / Dieser Beitrag ist mit Zustimmung des Rechteinhabers aufgrund einer (DFG-geförderten) Allianz- bzw. Nationallizenz frei zugänglich.

Spatial confinement of electrons and their interactions as well as confinement of the spin dimensionality often yield drastic changes of the electronic and magnetic properties of solids. Novel quantum transport and optical phenomena, involving electronic spin degrees of freedom in semiconductor heterostructures, as well as a rich variety of exotic quantum ground states and magnetic excitations in complex transition metal oxides that arise upon such confinements, belong therefore to topical problems of contemporary condensed matter physics. In this work electron spin systems in reduced dimensions are studied with Electron Spin Resonance (ESR) spectroscopy, a method which can provide important information on the energy spectrum of the spin states, spin dynamics, and magnetic correlations. The studied systems include quasi onedimensional spin chain materials based on transition metals Cu and Ni. Another class of materials are semiconductor heterostructures made of Si and Ge. Part I deals with the theoretical background of ESR and the description of the experimental ESR setups used which have been optimized for the purposes of the present work. In particular, the development and implementation of axial and transverse cylindrical resonant cavities for high-field highfrequency ESR experiments is discussed. The high quality factors of these cavities allow for sensitive measurements on μm-sized samples. They are used for the investigations on the spin-chain materials. The implementation and characterization of a setup for electrical detected magnetic resonance is presented. In Part II ESR studies and complementary results of other experimental techniques on two spin chain materials are presented. The Cu-based material Linarite is investigated in the paramagnetic regime above T > 2.8 K. This natural crystal constitutes a highly frustrated spin 1/2 Heisenberg chain with ferromagnetic nearest-neighbor and antiferromagnetic next-nearestneighbor interactions. The ESR data reveals that the significant magnetic anisotropy is due to anisotropy of the g-factor. Quantitative analysis of the critical broadening of the linewidth suggest appreciable interchain and interlayer spin correlations well above the ordering temperature. The Ni-based system is an organic-anorganic hybrid material where the Ni2+ ions possessing the integer spin S = 1 are magnetically coupled along one spatial direction. Indeed, the ESR study reveals an isotropic spin-1 Heisenberg chain in this system which unlike the Cu half integer spin-1/2 chain is expected to possess a qualitatively different non-magnetic singlet ground state separated from an excited magnetic state by a so-called Haldane gap. Surprisingly, in contrast to the expected Haldane behavior a competition between a magnetically ordered ground state and a potentially gapped state is revealed. In Part III investigations on SiGe/Si quantum dot structures are presented. The ESR investigations reveal narrowlines close to the free electron g-factor associated with electrons on the quantum dots. Their dephasing and relaxation times are determined. Manipulations with sub-bandgap light allow to change the relative population between the observed states. On the basis of extensive characterizations, strain, electronic structure and confined states on the Si-based structures are modeled with the program nextnano3. A qualitative model, explaining the energy spectrum of the spin states is proposed.

Fundação de Amparo a Pesquisa do Estado de Minas Gerais / In this work we have employed the Melting-Nucleation method in order to synthesize semiconductor and semimagnetic quantum dots (QDs), CdSe, CdSxSe1-x, CdS e Cd1-xMnxS, in a glass matrix. We have investigated these QDs by using several experimental techniques and theoretical models, reaching a comprehensive understanding of their fundamental properties. The lattice contraction in CdSe QDs was confirmed by Raman spectroscopy, evidencing that the glass matrix (host material) plays an important role on the vibrational modes of nanocrystals (NCs). Advancement in the synthesis of pseudo-bynary CdSxSe1-x QDs was achieved by obtaining a good control on the alloy composition in two variants of precursor dopings, while the QD size is tuned by annealing. Resonant Raman spectra of these CdSxSe1-x QDs were very well described by the continuum lattice dynamics model, suggesting the propagation of optical phonons within the NC. By studying CdS QDs by temperaturedependent Raman spectroscopy, we have demonstrated that there is a large difference between the thermal expansion coefficients of QD e of bulk material. The same conclusions were obtained for the modal Grüneisen parameters and for the anharmonicity coupling constants, so that they have to be estimated independently of bulk parameters in the study of thermal properties of QDs. We have employed the Electron Paramagnetic Resonance in order to confirm that the migration of Mn2+ ions in Cd1-xMnxS NCs, from the core to the surface, can be controlled by a thermal annealing. We have proved yet that the luminescence emitted by Cd1-xMnxS NCs can be controlled by changing the x concentration and by the thermal annealing, in which the emission of Mn2+ ions (4T1 6A1) is only observed when this magnetic impurity is substitutionally into the core of Cd1-xMnxS NC. From temperature-dependent photoluminescence measurements, we have come up with a model based on rate equations that describes well the energy transfers involving two coupled groups of Cd1-xMnxS NPs. Further emissions from deep defect levels were attributed to two energetically different divacancies, VCd VS, in the wurtzite structure of Cd1-xMnxS NPs, which can be controlled by the magnetic doping. By studying the magneto-optical properties of Cd1-xMnxS NPs, we have demonstrated that the self-purification is the dominant mechanism controlling the doping process in semiconductor QDs grown by the melting-nucleation method. We have demonstrated that the multiphonon Raman scattering in the coupled Cd1-xMnxS NPs, as well as the coupling strength between electrons and optical phonons, can satisfactorily be tuned by the magnetic doping with Mn2+ ions and by an appropriate thermal annealing. Furthermore, we have verified that the magnetic doping have induced variations on the sp-d exchange interaction and in the crystalline quality of NPs. / Neste trabalho nós utilizamos o método de Fusão-Nucleação para sintetizar pontos quânticos (PQs) semicondutores e semimagnéticos, CdSe, CdSxSe1-x, CdS e Cd1-xMnxS, em uma matriz vítrea. Nós investigamos estes PQs utilizando várias técnicas experimentais e modelos teóricos, obtendo um entendimento compreensivo das suas propriedades fundamentais. A contração da rede cristalina nos PQs de CdSe foi confirmada pela espectroscopia Raman, evidenciando que a matriz vítrea (material hospedeiro) desempenha um papel importante sobre os modos vibracionais dos nanocristais (NCs). Um avanço na síntese de PQs pseudo-binários de CdSxSe1-x foi alcançado, obtendo um bom controle sobre a composição da liga em duas variações de dopantes precursores, enquanto o tamanho do PQ é controlado pelo recozimento. Os espectros Raman ressonantes destes PQs de CdSxSe1-x foram muito bem descritos pelo modelo da dinâmica de rede contínua, sugerindo a propagação de fônons ópticos dentro do NC. Ao estudar PQs de CdS por espectroscopia Raman dependente da temperatura, nós demonstramos que existe uma grande diferença entre os coeficientes de expansão térmica do PQ e do material bulk. As mesmas conclusões foram obtidas para os parâmetros de Grüneisen modais e para as constantes de acoplamento da anarmonicidade, de maneira que eles devem ser estimados independentemente dos parâmetros do bulk no estudo das propriedades térmicas dos PQs. Nós utilizamos a Ressonância Paramagnética Eletrônica para confirmar que a migração de íons Mn2+ em NCs de Cd1-xMnxS, do núcleo para a superfície, pode ser controlada por um recozimento térmico. Comprovamos ainda que a luminescência emitida pelos NCs de Cd1-xMnxS pode ser controlada pela modificação da concentração x e pelo recozimento térmico, em que a emissão dos íons Mn2+ (4T1 6A1) é somente observada quando esta impureza magnética está substitucionalmente incorporada no núcleo do NC de Cd1-xMnxS. A partir de medidas de fotoluminescência dependente da temperatura, nós desenvolvemos um modelo baseado em equações de taxa que descreve bem as transferências de energia envolvendo dois grupos acoplados de nanopartículas (NPs) de Cd1-xMnxS. Emissões adicionais a partir de níveis de defeitos profundos que foram atribuídos duas divacâncias energeticamente diferentes, VCd VS, na estrutura wurtzita das NPs de Cd1-xMnxS, que podem ser controladas pela dopagem magnética. Ao estudar as propriedades magneto-ópticas das NPs de Cd1-xMnxS, nós demonstramos que a autopurificação é o mecanismo dominante controlando o processo de dopagem em PQs semicondutores crescidos pelo método de fusão-nucleação. Nós demonstramos que o espalhamento Raman multi-fônon nas NPs de Cd1-xMnxS acopladas, bem como a força do acoplamento entre elétrons e fônons ópticos, podem ser adequadamente sintonizados pela dopagem magnética com íons Mn2+ e por um recozimento térmico apropriado. Além disso, verificamos que a dopagem magnética induziu variações na interação de troca sp-d e na qualidade cristalina das NPs. / Doutor em Física

Polycrystalline Zn1-xCrxO (0.01 ≤ x ≤ 0.09) samples synthesized by solid state reaction technique were sintered at different temperatures following slow step sintering schedule. Structural, micro-structural, optical, magnetic properties and homogeneity were investigated using suitable characterisation techniques. Cr2O3 and CrO2 phases have been detected in the XRD patterns and Raman spectra of Zn1-xCrxO samples with x ≥ 0.05. Photoluminescence study has indicated improved optical property of the samples compared to undoped ZnO. While low percentage Cr doped samples showed diamagnetic behaviour, higher percentage doped samples (≥ 5%) exhibited ferromagnetic, paramagnetic and anti-ferromagnetic behaviours depending upon the sintering temperatures. The magnetic properties have been analysed through Electron Spin Resonance study. A g-value of 1.97 indicates Cr in +3 valence state in doped ZnO system. Presence of Cr3+ and Cr4+ in ZnO is understood to facilitate super exchange interactions to promote ferromagnetism at room temperature. ESR study shows improved magnetic homogeneity achieved by slow step sintering process. / Physics / M. Sc. (Physics)

The path towards mitigation of anthropogenic greenhouse gas emissions lies in the transition from conventional to sustainable energy resources. The Hydrogen Economy, a cyclic economy based on hydrogen as a fuel, is suggested as a tool in the necessary energy transition. Photocatalysis makes use of sunlight to promote thermodynamically non-favoured reactions such as water splitting, allowing for sustainable hydrogen production. Harvesting thermal energy along with photonic energy is an interesting concept to decrease the activation energy of water splitting (i.e. ΔG = + 237.2 kJ∙mol−1). This work aims to confront this hypothesis in a gas phase photo-thermal reactor designed specifically for this study. The photocatalyst chosen is graphitic carbon nitride (g-C3N4), an organic semiconductor possessing a narrow band gap (i.e. 2.7 eV) as well as a band structure which theoretically permits water splitting. The photocatalytic performance of Pt/g-C3N4 for hydrogen evolution was tuned by altering its synthetic temperature. Electron paramagnetic resonance was used to gain insight on the evolution of the photocatalyst activity with synthesis temperature. Then, gold nanoparticles were deposited on g-C3N4 surface. Localized surface plasmon resonance properties of gold nanoparticles are reported in the literature to be influenced by temperature. Therefore Au/g-C3N4 appeared as a promising candidate for photo-thermal water splitting. X-ray spectroscopy unveiled interesting observations on the gold oxidation state. Moreover, under specific reduction conditions, gold nanoparticles with a wide variety of shapes characterized by sharp edges were formed. Finally, the development of the photo-thermal reactor is presented. The design process and the implementation of this innovative reactor are discussed. The reactor was successfully utilized to probe photoreactions. Then, the highly energy-demanding photocatalytic water splitting was proven not to be activated by temperature in the photo-thermal apparatus.