O uso crescente de dispositivos móveis e o advento da Internet das Coisas têm demandado esforços para prover alternativas de comunicação sem fio. A utilização de sistemas óticos para a transmissão de dados apresenta-se como uma tecnologia promissora e complementar à comunicação por radiofrequência, especialmente devido aos desenvolvimentos consideráveis na tecnologia de iluminação por estado sólido e sua adoção em vários domínios. Os diodos de emissão de luz podem ser utilizados na promoção de comunicação por luz visível em ambientes internos e externos. Nos ambientes externos há inúmeras oportunidades a serem exploradas no que concerne aos Sistemas Inteligentes de Transporte, visto que os diodos de emissão de luz têm sido utilizados em luminárias públicas, semáforos e veículos. Esta pesquisa propôs o desenvolvimento e a avaliação de um sistema de comunicação por luz visível entre elementos da infraestrutura urbana e veículos, mais especificamente, luminárias públicas baseadas em diodos de emissão de luz e o modal de transporte público representado pelos ônibus que circulam em faixas exclusivas. A metodologia foi composta por simulação computacional e pela construção de um protótipo para auxiliar na validação das soluções propostas. O sistema complementar de comunicação sem fio por meio da luz proposto fornece pode fornecer subsídios à determinação do posicionamento preciso dos ônibus, suprindo as deficiências do sistema GPS em locais menos favoráveis à recepção de seus sinais em uma cidade. Essas informações auxiliam os usuários e os gestores do transporte público, atendendo alguns domínios de serviço em Sistemas Inteligentes de Transporte, de acordo com a norma ISO 14813. Os resultados obtidos nos testes com o protótipo, bem como, aqueles observados na simulação, comprovaram a viabilidade do sistema proposto, com o estabelecimento da comunicação entre luminária e ônibus, inclusive quando trafegando a 60 km/h. / The increasing use of mobile devices and the advent of the Internet of Things have called for efforts to provide alternatives for wireless communication. The use of optical systems for data transmission is a promising and complementary technology to radiofrequency communication, especially due to the considerable developments in solidstate lighting technology and its adoption in various domains. Light-emitting diodes can be used to promote visible light communication in indoor and outdoor environments. In outdoor environments there are numerous opportunities to be explored with regard to Intelligent Transport Systems, since light-emitting diodes have been used in public luminaires, traffic lights and vehicles. This research proposed the development and evaluation of a visible light communication system between elements of the urban infrastructure and vehicles, more specifically, public luminaires based on light-emitting diodes and the mode of public transport represented by buses that circulate in exclusive lanes. The methodology was composed by computational simulation and the construction of a prototype, to assist in the validation of the proposed solutions. The proposed complementary wireless communication system through light provides subsidies to determine the precise positioning of buses, supplying deficiencies of the GPS system in places less favorable to the reception of their signals in a city. This information helps the users and the managers of the public transport, attending some service domains in Intelligent Transport Systems, according to the ISO 14813 standard. The results obtained in the tests with the prototype, as well as those observed in the simulation, proved the feasibility of the proposed system, with the establishment of communication between luminaire and bus, even when traveling at 60 km/h.

Esta tese de doutorado é o resultado de um estudo dos mecanismos de operação de dispositivos poliméricos emissores de luz, com um particular enfoque nos processos de injeção e transporte de portadores de carga em polímeros derivados do poli(p-fenileno vinileno), PPV. Para tanto, se fez necessário o domínio de todas as etapas de produção e caracterização, desde a síntese química dos polímeros até a fabricação propriamente dita dos dispositivos, as quais são brevemente descritas neste trabalho. Basicamente, dois tipos diferentes de dispositivos foram caracterizados: diodos poliméricos emissores de luz (PLEDs), nos quais a camada ativa é composta por um filme fino (100-500 nm de espessura) do polímero eletroluminescente puro, e células eletroquímicas emissoras de luz (LECs), compostas por blendas do polímero conjugado com um eletrólito polimérico condutor iônico. As propriedades ópticas dos dispositivos foram analisadas através dos espectros de absorção óptica na região do ultravioleta/visível e de emissão (foto e eletroluminescência) enquanto as propriedades de injeção e de transporte de carga foram exploradas através de medidas elétricas de corrente-voltagem (I-V), espectroscopia de impedância no domínio da freqüência (condutividade ac), espectroscopia de fotocorrente e ressonância magnética detectada eletricamente (EDMR). A influência de parâmetros como a estrutura dos dispositivos, os metais utilizados como eletrodos e a temperatura permitiram uma análise mais detalhada de alguns modelos teóricos utilizados na interpretação dos resultados experimentais, fornecendo, dessa forma, um maior conhecimento das propriedades físicas dos materiais estudados. / This PhD thesis is an extensive study of the operation mechanisms of polymeric light-emitting devices, with a particular focus on the injection and transport properties of charge-carriers in poly(p-phenylene vinylene), PPV, derivatives. Therefore, it was necessary to dominate all the processes of fabrication and characterization of such devices, from the chemical synthesis of the polymers to the device fabrication, which are briefly described along this work. Two different kinds of devices were studied: polymeric ligh-emitting diodes (PLEDs) composed by a single thin layer (100-500 nm thick) of the pure electroluminescent polymer, and light-emitting electrochemical cells (LECs), which active layers are formed by a blend of the conjugated polymer and an ionic conductive polymeric electrolyte. The optical properties of the devices were analyzed by optical absorption in the ultraviolet-visible range and emission (photo- and electroluminescence) spectra. The charge injection and transport properties were studied by electrical measurements like current-voltage (I-V) curves, impedance spectroscopy in the frequency domain (ac conductivity), photocurrent spectroscopy and electrically detected magnetic resonance (EDMR). The influence of parameters like the device structure, the electrodes work function and the temperature allowed a detailed analysis of some theoretical models commonly used in the interpretation of the experimental results, providing more information about the physical properties of the studied conjugated polymers.

Les procédés de photopolymérisation connaissent un développement important avec des applications considérables dans le milieu industriel en raison de ses avantages économiques et écologiques. Les réactions de photopolymérisation sont très représentées, elles reposent sur l’utilisation d’un composé ou d'un système photosensible sous irradiation, générant des espèces réactives capables d’amorcer la polymérisation et de réagir avec le monomère. Le principal objectif de ce travail de thèse consiste à développer des molécules efficaces comme photoamorceurs (PA) pour la photopolymérisation radicalaire (FRP) d’une part et la photopolymérisation cationique (CP) ou la photopolymérisation cationique sensibilisée par les radicaux (FRPCP) d’autre part. Nous nous sommes intéressés à des systèmes amorceurs hautes performances absorbant fortement dans le domaine du visible et permettant l’utilisation de lampes non nocives et à faible consommation d'énergie : les diodes électroluminescentes (LED). Ainsi, un procédé original portant sur la combinaison de la photopolymérisation radicalaire et la photopolymérisation cationique en une seule étape a été examiné. Cette approche a fait appel à la synthèse de réseaux interpénétrés de polymères (RIP) comportant les propriétés spécifiques de chaque polymère. Les efforts ont été consacrés au développement de nouveaux composés avec de nouvelles structures chimiques et d’excellentes propriétés d’absorption de lumière avec de coefficients d’extinctions molaires très élevés.Des systèmes construits sur l’utilisation de différentes structures comme photoamorceurs ont pu être mis au point dans le cadre de cette thèse. La possibilité d’utiliser des colorants présentant un caractère push-pull, ou des colorants étant caractérisés par une structure polyène ou une structure polyaromatique a pu être considérée. Egalement, des structures à base de xanthène sensibles dans le domaine proche visible ont pu être proposées. De plus, ce travail a permis d’étudier de nouveaux systèmes photoamorceurs à base de structures minérales telles que les polyoxométallates ou les pérovskites. Ainsi, la possibilité de proposer de nouveaux sels d’iodonium à base de coumarine a pu être démontrée. Des meilleures performances ont été atteintes en utilisant des systèmes photoamorceurs à deux composants (PA/Ph2I+) ou à trois composants (PA/Ph2I+/additif) dans des conditions d’irradiation douce. Afin d’étudier et caractériser ces photoamorceurs, la cinétique de la réaction de photopolymérisation a été suivie par spectroscopie infrarouge à transformée de Fourier (RT-FTIR). Les radicaux générés ont été détectés par résonance paramagnétique électronique (RPE). La photolyse laser éclair (LFP) a été utilisée comme technique complémentaire pour étudier l’efficacité et la réactivité de radicaux générés. / The photopolymerization reaction is used in an increasing number of industrial applications because of the remarkable performance of the process. The photopolymerization reactions require the presence of photosensitive compounds. These latter can absorb light and participate in the photoinitiation through the generation of reactive species. The main objective of this PHD was to develop efficient molecules as photoinitiators (PI) for the free radical photopolymerization (FRP), the cationic photopolymerization (CP) and the free radical promoted cationic photopolymerization (FRPCP). We were interested in new high performance photoinitiating systems (PISs) exhibiting excellent light absorption properties (especially in the visible wavelength range). The photopolymerization must be carried out under soft irradiation conditions (non harmful lamps, low energy consumption and low intensity sources: light-emitting diodes LED). Thus, a novel method involving concomitant radical/cationic photopolymerization in one step was examined. This approach involves the synthesis of interpenetrating polymer networks (IPNs) comprising the specific properties of each polymer. The efforts have been devoted to the development of new compounds with new chemical structures and excellent light absorption properties with high molar extinctions coefficients.Many PISs based on different photoinitiators structures have been developed in this work. The possibility to use dyes having a push-pull character, or dyes being characterized by a polyene or polyaromatic structures were considered. Also, originals xanthenes derivatives sensitive in the visible region have been proposed. In particular, this work has enabled the study of new PISs based on inorganic structures such as polyoxometalates and perovskites. Thus, the possibility to propose new iodonium salts based coumarin could be demonstrated. The best performance was achieved using two-components (PI/Ph2I+) or three-components (PI /Ph2I+/additive) photoinitiating systems under soft irradiation conditions. The kinetics of photopolymerization were evaluated using real time FTIR spectroscopy. The generated radicals were observed using the electron spin resonance (ESR) technique. The laser flash photolysis (LFP) was used as a complementary technique to study the efficiency and the reactivity of radicals generated.

Single self-assembled semiconductor quantum dots (QDs) are able to emit single-photons and entangled-photons pairs. They are therefore considered as potential candidate building blocks for quantum information processing (QIP) and communication. To exploit them fully, the ability to precisely control their optical properties is needed due to several reasons. For example, the stochastic nature of their growth ends up with only little probability of finding any two or more QDs emitting indistinguishable photons. These are required for two-photon quantum interference (partial Bell-state measurement), which lies at the heart of linear optics QIP. Also, most of the as-grown QDs do not fulfil the symmetries required for generation of entangled-photon pairs. Additionally, tuning is required to establish completely new systems, for example, 87Rb atomic-vapors based hybrid semiconductoratomic (HSA) interface or QDs with significant heavy-hole (HH)-light-hole (LH) mixings. The former paves a way towards quantum memories and the latter makes the optical control of hole spins much easier required for spin- based QIP. This work focuses on the optical properties of a new type of QDs optimized for HSA experiments and their broadband tuning using strain. It was created by integrating the membranes, containing QDs, onto relaxor-ferroelectric actuators and was quantified with a spatial resolution of ~1 µm by combining measurements of the µ-photoluminescence of the regions surrounding the QDs and dedicated modeling. The emission of a neutral exciton confined in a QD usually consists of two fine-structure-split lines which are linearly polarized along orthogonal directions. In our QDs we tune the emission energies as large as ~23meV and the fine-structure-splitting by more than 90 µeV. For the first time, we demonstrate that strain is able to tune the angle between the polarization direction of these two lines up to 40° due to increased strain-induced HH-LH mixings up to ~55%. Compared to other quantum emitters, QDs can be easily integrated into optoelectronic devices, which enable, for example, the generation of non-classical light under electrical injection. A novel method to create sub-micrometer sized current-channels to efficiently feed charge carriers into single QDs is presented in this thesis. It is based on focused-laserbeam assisted thermal diffusion of manganese interstitial ions from the top GaMnAs layer into the underlying layer of resonant tunneling diode structures. The combination of the two methods investigated in this thesis may lead to new QDbased devices, where direct laser writing is employed to preselect QDs by creating localized current-channels and strain is used to fine tune their optical properties to match the demanding requirements imposed by QIP concepts.

This work demonstrates an approach to develop low-cost, semi-transparent, long-term stable, and efficient organic photovoltaic (OPV) cells and organic light-emitting diodes (OLEDs) using various alternative electrodes such as conductive polymers, doped ZnO, and carbon nanotubes. Such electrodes are regarded as good candidates to replace the conventional indium tin oxide (ITO) electrode, which is expensive, brittle, and limiting the manufacturing of low-cost, flexible organic devices. First, we report long-term stable, efficient ITO-free OPV cells and transparent OLEDs based on poly(3,4-ethylene-dioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) electrodes by using a solvent post-treatment or a structure optimization. In addition, a high performance internal light out-coupling system for white OLEDs based on PEDOT:PSS-coated metal oxide nanostructures is developed. Next, we demonstrate highly efficient ITO-free OPV cells and OLEDs with optimized ZnO electrodes doped with alternative non-metallic elements. The organic devices based on the optimized ZnO electrodes show significantly improved efficiencies compared to devices with standard ITO. Finally, we report semi-transparent OPV cells with free-standing carbon nanotube sheets as transparent top electrodes. The resulting OPV cells exhibit very low leakage currents with good long-term stability. In addition, the combination of various kinds of bottom and top electrodes for semi-transparent and ITO-free OPV cells is investigated. These results demonstrate that alternative electrodes-based OPV cells and OLEDs have a promising future for practical applications in efficient, low-cost, flexible and semi-transparent device manufacturing. / Die vorliegende Arbeit demonstriert einen Ansatz zur Verwirklichung von kostengünstigen, semi-transparenten, langzeitstabilen und effizienten Organischen Photovoltaik Zellen (OPV) und Organischen Leuchtdioden (OLEDs) durch die Nutzung innovativer Elektrodensysteme. Dazu werden leitfähige Polymere, dotiertes ZnO und Kohlenstoff-Nanoröhrchen eingesetzt. Diese alternativen Elektrodensysteme sind vielversprechende Kandidaten, um das konventionell genutzte Indium-Zinn-Oxid (ITO), welches aufgrund seines hohen Preises und spröden Materialverhaltens einen stark begrenz Faktor bei der Herstellung von kostengünstigen, flexiblen, organischen Bauelementen darstellt, zu ersetzten. Zunächst werden langzeitstabile, effiziente, ITO-freie Solarzellen und transparente OLEDs auf der Basis von Poly(3,4-ethylene-dioxythiophene):Poly(styrenesulfonate) (PEDOT:PSS) Elektroden beschrieben, welche mit Hilfe einer Lösungsmittel-Nachprozessierung und einer Optimierung der Bauelementstruktur hergestellt wurden. Zusätzlich wurde ein leistungsfähiges, internes Lichtauskopplungs-System für weiße OLEDs, basierend auf PEDOT:PSS-beschichteten Metalloxid-Nanostrukturen, entwickelt. Weiterhin werden hoch effiziente, ITO-freie OPV Zellen und OLEDs vorgestellt, bei denen mit verschiedenen nicht-metallischen Elementen dotierte ZnO Elektroden zur Anwendung kamen. Die optimierten ZnO Elektroden bieten im Vergleich zu unserem Laborstandard ITO eine signifikant verbesserte Effizienz. Abschließend werden semi-transparente OPV Zellen mit freistehenden Kohlenstoff-Nanoröhrchen als transparente Top-Elektrode vorgestellt. Die daraus resultierenden Zellen zeigen sehr niedrige Leckströme und eine zufriedenstellende Stabilität. In diesem Zusammenhang wurde auch verschiedene Kombinationen von Elektrodenmaterialen als Top- und Bottom-Elektrode für semi-transparente, ITO-freie OPV Zellen untersucht. Zusammengefasst bestätigen die Resultate, dass OPV und OLEDs basierend auf alternativen Elektroden vielversprechende Eigenschaften für die praktische Anwendung in der Herstellung von effizienten, kostengünstigen, flexiblen und semi-transparenten Bauelement besitzen.

Porous metal oxides formed by supercritical carbon dioxide (SCCO2) treatments at low temperature were used for displays, solar cells, and light emitting diodes (LEDs) applications. The SCCO2 fluid, also known as green solvents, exhibits low viscosity, low surface tension and high diffusivity as gases, and high density and solubility same with liquids. In this thesis, we successfully fabricated porous antimony-doped tin oxide (ATO) and porous indium tin oxide (ITO) by the SCCO2 treatments. In addition, the treatment can also be used to improve the work function and surface energy of ITO anode of an organic LED (OLED). The performance of the OLEDs was drastically enhanced in comparison with that of the devices without any ITO surface treatments. First, the porous ATO films were formed by the SCCO2 treatment for absorption of silver molecules in silver electro deposition devices. The porosity, resistivity and average optical transmittance of the porous ATO film in visible wavelength were 43.1%, 3 £[-cm and 90.4%, respectively. For the silver electro deposition devices with the porous ATO film, the transmittance contrast ratio of larger than 12 in visible spectrum was obtained at an operating voltage of 1.5 V. Furthermore, for the 0.25 cm2 device, the switching time of 4.5 seconds was achieved by applying a square-wave voltage ranging from 1.5 to -0.2 V between the electrodes. On the other hand, the porous ITO with low refractive index was prepared by SCCO2/IPA treatment on gel-coated ITO thin films. The high refractive index of the ITO film was achieved by long-throw radio-frequency magnetron sputtering technique at room temperature. The index contrast (£Gn) was higher than 0.6 between porous ITO and sputtered ITO films. The large £Gn is useful for fabricating conductive anti-reflection (AR) and high reflection (HR) structures using the porous ITO on sputtered ITO bilayers. The weighted average reflectance and transmittance of 4.3% and 83.1% were achieved for the double-layer ITO AR electrode with a sheet resistance of 1.1 K£[/¡E. For HR structures, the reflectance and sheet resistance were 87.9% and 35 £[/¡E with 4 periods ITO bilayers. Finally, the SCCO2 treatments with strong oxidizer H2O2 were proposed to modify surface property of ITO anode of a fluorescent OLED. The highest work function and surface energy of 5.5 eV and 74.8 mJ/m2 was achieved by the SCCO2/H2O2 treatment. For the OLED with 15 min SCCO2 treatment at 4000 psi, the turn-on voltage and maximum power efficiency of 6.5 V and 1.94 lm/W were obtained. The power efficiency was 19.3% and 33.8% higher than those of the OLEDs with oxygen plasma treated and as-cleaned ITO anodes.

In this thesis, we investigated several photoelectric material systems consisted of conjugated polymers by means of computer simulation. We combined several theory and simulation methods to meodeling different subjects from atomic to mesoscopic scale. We dealt with the problems such as quantum efficiency, structure characteristic, and the phase behavior in material. We hope to have better understanding of the relationship between structure characteristic and functional property in material. It will help an engineering designer to adjust the variables that optimize characteristics linking the synthesis of advanced materials with desired physical properties. This work can be divided into three parts. Long side chain substituted PPV polymers applied in light-emitting diode material : Molecular dynamics simulations were employed to investigate structure features and segment orientation of four poly(phenylene vinylene) (PPV)-like conjugated polymers with long flexible side chains at room temperature. In the simulations, the main chains of the polymers were found to be semi-rigid and to exhibit a tendency to coil into ellipsoidal helices or form zigzag conformations of only limited regularity. It was shown that continuous segments of a chain which are quasi-coplanar along the backbone are in a range of 2~4 repeat units. This implies that long-range electron transfer along same backbones of these polymers may not happen but may be mediated by interchain interactions. The ordered orientation and coupling distance of interchain aromatic rings are found to correlate with important optical properties of materials. Then we combined molecular dynamics simulation and density matrix methods modeling of amorphous light-emitting polymers. A simplified method combining molecular dynamics (MD) simulation and density matrix (DM) theory was developed for the prediction of optical properties of long side chain substituted poly(phenylene vinylene) (PPV) polymers. This MD+DM method takes account of the complexity of molecular packing of polymer chains. The method has been tested to simulate the absorption spectra of four model systems. The wavelengths of absorption maxima of the calculated spectra of these four conjugated polymers are in reasonable agreement with experimental data. The simulation also demonstrated that the importance of including interchain interactions in the calculation. Ion-conducting polymer sPBI-PS(Li+): To understand the mechanism of ionic migration in the amorphous matrixes of polymer electrolytes is crucial for their applications in modern technologies. Here, molecular dynamics (MD) simulation was carried out to investigate the ionic conduction mechanism of a particular conjugated rigid-rod polymer, sPBI-PS(Li+). The backbone of this polymer is poly[(1, 7- dihydrobenzo[1, 2-d:4,5-d¡¦]diimidazole- 2,6-diyl)-2-(2-sulfo)-p-phenylene]. The polymer has pendants of propane sulfonate Li+ ionomer. The MD simulations showed that the main chains of sPBI-PS(Li+) are in layer-like structure. The further detailed structure analysis suggested that the £k-electron of this polymer is not delocalized among aromatic rings. This agrees with the experimental result that sPBI-PS(Li+) shows no electronic conductivity and the conductivity of this polymer is mainly ionic. The calculated migration channels of lithium ions and electrostatic potential distributions indicated clearly that the polymer matrix is anisotropic for the migrations of ions. The migration of lithium ions along the longitudinal direction is more preferable than that along the transverse direction. The relaxations of the polymer host were found to play important roles in the transfer process of lithium ions. The hopping of lithium ion from one -SO3-1 group to another is correlated strongly with characteristic motions of -SO3-1 group on a time scale of about 10-13 s. Self-assembly functional material. Dissipative particle dynamics (DPD) simulations were carried out to investigate mixed ionic and non-ionic molecules, sodium tetradecyl sulfate (STS) and tetradecyl triethoxylated ether (C14E3) aqueous system. Different types of mixed micelles are formed depending on the concentrations of STS and C14E3. Our results are in good agreement to the early NMR measurements. From the investigation of surfactant aggregation, we understand the self-assembly mechanism and classical phase behavior in general diblock copolymer. Further, we investigated the self-assembly process on a particular mushroom-shaped supramolecular film material from molecular character to phase behavior. The miniaturized rod-coil triblock copolymers (PS-PI-RCBC) HEMME had been found to self-assemble into well-ordered nanostructures and unusual head to tail multilayer structure. The purpose of our study is to obtain fundamental understanding the connection of the inherent morphological characterization of single molecule and the mechanism of phase behavior of this polar self-assembly system. Dissipative particle dynamics simulation was carried out to study the mechanism of phase behavior of the solvent-copolymers system. We found that the solvent-induced polar effect under different temperature is important in the process of self-assembly of block copolymers. In different temperature the solvent induces hybrid structure aggregation. Our results are consistent with experimental observations and give evidence for a special mechanism governing the unusual phase behavior in thin films of modulated phases. The sizes and stabilization energies of mushroom-shaped supramolecular clusters were predicted by molecular modeling method. Clusters of sizes from 16 to 90 molecules were found to be stable. In combination of classical and simple quantum mechanical calculations, the band gaps of HEMME clusters with various sizes were estimated. The band gap was converged at 2.45 eV for cluster contains 90 molecules. Nonlinear optical properties of the material were investigated by the semi-empirical quantum mechanical calculations of molecular dipole moment and hyperpolarizabilities. Significant second-order nonlinear optical properties were shown from these calculated properties.

In this work, well-defined and stable thin films based on polythiophene and its derivative, are employed as the hole-injection contact of organic light-emitting diodes (OLED). The polymer films are obtained by the electropolymerization or the electrochemical doping/dedoping of a spin-coated layer. Their electrical properties and energetics are tailored by electrochemical adjustment of their doping levels in order to improve the hole-injection from the anode as well as the performance of small molecular OLEDs. By using dimeric thiophene and optimizing the electrodeposition parameters, a thin polybithiophene (PbT) layer is fabricated with well-defined morphology and a high degree of smoothness by electro-polymerization. The introduction of the semiconducting PbT contact layer improves remarkably the hole injection between ITO anode and the hole- transport layer (NPB) due to its favourable energetic feature (HOMO level of 5.1 eV). The vapor-deposited NPB/Alq3 bilayer OLEDs with a thin PbT interlayer, show a remarkable reduction of the operating voltage as well as enhanced luminous efficiency compared to the devices without PbT. Investigations have also been made on the influence of PbT thickness on the efficiency and I-V feature as well as device stability of the OLED. It is demonstrated that the use of an electropolymerization step into the production of vapor deposited molecular OLED is a viable approach to obtain high performance OLEDs. The study on the PbT has been extended to poly(3,4-ethylenedioxythiophene) (PEDT) and the highly homogenous poly(styrenesulfonate) (PSS) doped PEDT layer from a spin-coating process has been applied. The doping level of PEDT:PSS was adjusted quantitatively by an electrochemical doping/dedoping process using a p-tuoluenesulfonic acid containing solution, and the redox mechanism was elucidated. The higher oxidation state can remain stable in the dry state. The work function of PEDT:PSS increases with the doping level after adjusting at an electrode potential higher than the value of the electrochemical equilibrium potential (Eeq) of an untreated film. This leads to a further reduction of the hole-injection barrier at the contact of the polymeric anode/hole transport layer and an ideal ohmic behavoir is almost achieved at the anode/NPB interface for a PEDT:PSS anode with very high doping level. Molecular Alq3-based OLEDs were fabricated using the electrochemically treated PEDT:PSS/ITO anode, and the device performance is shown to depend on the doping level of polymeric anode. The devices on the polymer anode with a higher Eeq than that for the unmodified anode, show a reduction of operating voltage as well as a remarkable enhancement of the luminance. Furthermore, it is found that the operating stability of such devices is also improved remarkably. This originates from the removal of mobile ions such as sodium ions inside the PEDT:PSS by electrochemical treatment as well as the planarization of the ITO surface by the polymer film. By utilizing an Al/LiF cathode with an enhanced electron injection and together with a high Eeq- anode, a balanced injection and recombination of hole and electron is achieved. It leads to a further reduction of the operating voltage and to a drastic improvement of EL efficiency of the device as high as 5.0 cd/A. The results demonstrate unambiguously that the electrochemical treatment of a cast polymer anode is an effective method to improve and optimize the performance of OLEDs. The method can be extended to other polythiophene systems and other conjugated polymers in the fabrication of the OLEDs as well as organic transistors and solar cells.

A numerical model and results for the quantitative simulation of multilayer organic light emitting diode (OLED) and organic solar cell (OSC) are presented. In the model, effects like bipolar charge carrier drift and diffusion with field-dependent mobilities, trapping, dopants, indirect and direct bimolecular recombination, singlet Frenkel exciton diffusion, normal decay and quenching effects are taken into account. For an adequate description of multilayer devices with energetic barriers at interfaces between two adjacent organic layers, thermally assisted charge carrier hopping through the interface, interface recombination, and formation of interface charge transfer (CT) states have been introduced in the model. For the simulation of OSC, the generation of carrier pairs in the mixed layer or at the interface is additionally implemented. The light absorption profile is calculated from optical simulations and used as an input for the electrical simulation. The model is based on three elements: the Poisson equation, the rate equations for charge carriers and the rate equations for singlet Frenkel excitons. These equations are simultaeously solved by spatial and temporal discretisation using the appropriate boundary conditions and electrical parameters. The solution is found when a steady state is reached, as indicated by a constant value of current density. The simulation provides a detailed look into the distribution of electric field and concentration of free and trapped carriers at a particular applied voltage. For organic light emitting diodes, the numerical model helps to analyze the problems of different structures and provides deeper insight into the relevant physical mechanisms involved in device operation. Moreover, it is possible to identify technological problems for certain sets of devices. For instance, we could show that ? in contrast to literature reports - the contact between Alq3 and LiF/Al did not show ohmic behaviour for the series of devices. The role of an additional organic blocking layer between HTL and EML was presented. The explanation for the higher creation efficiency for singlet excitons in the three-layer structure is found in the separation of free holes and electrons accumulating close to the internal interface 1-Naphdata/Alq3. The numerical calculation has demonstrated the importance of controlled doping of the organic materials, which is a way to obtain efficient light emitting diodes with low operating voltage. The experimental results has been reproduced by numerical simulation for a series of OLEDs with different thicknesses of the hole transport layer and emitting layer and for doped emitting layers. The advantages and drawbacks of solar cells based on flat heterojunctions and bulk heterojunctions are analyzed. From the simulations, it can be understood why bulk-heterojunctions typically yield higher photocurrents while flat heterojunctions typically feature higher fill factors. In p-i-n ?structures, p and n are doped wide gap materials and i is a photoactive donor-acceptor blend layer using, e.g,. zinc phthalocyanine as a donor and C60 as an acceptor component. It is found that by introducing trap states, the simulation is able to reproduce the linear dependence of short circuit currents on the light intensity. The apparent light-induced shunt resistance often observed in organic solar cells can also be explained by losses due to trapping and indirect recombination of photogenerated carriers, which we consider a crucial point of our work. However, these two effects, the linear scaling of the photocurrent with light intensity and the apparent photoshunt, could also be reproduced when field-dependent geminate recombination is assumed to play a dominant role. First results that show a temperature independent short circuit photocurrent favour the model based on trap-mediated indirect recombination.

Photo-induced charge transfer which occurs between molecules or different parts of a large molecule is the pivotal process related to performances of organic electronics. In particular, injection of charge carriers into conjugated polymers and dissociation of photo-generated excitons at the heterojunction between a donor and acceptor system are of great importance in determining the luminescence efficiency of organic light emitting diodes (OLEDs) and solar energy conversion efficiency of organic solar cells, respectively. However, the complex nature of organic semiconductors as well as complicated primary processes involved in the functioning of these devices have prevented us from understanding unique characteristics of these processes and thereby engineering better materials for higher performances. In this dissertation, two different types of photo-induced (or -related) charge transfer processes occurring in organic semiconductors were investigated by using single molecule spectroscopy (SMS) techniques to unravel the complexities of these processes. The carefully designed functioning capacitor-like model devices similar to OLEDs and photovoltaic cells were fabricated where isolated single nanoparticles were introduced as an active medium to mitigate the complexities of these materials. We observed that injection of positively charged carriers (holes) into poly[2-methoxy-5-(2'-ethyl-hexyloxy)-1,4-phenylene vinylene] (MEH-PPV) single nanoparticles from the carbazole hole transport layer does not occur in the absence of light. We denoted the observed hole injection in aid of light as the light-induced hole transfer mechanism (LIHT). It was revealed that the charging dynamics are highly consistent with a cooperative charging effect. In addition, the LIHT was proposed as the possible source for the formation of deep trapped hole in organic devices. Local exciton dissociation yields across a nanostructured domain between poly(9,9-dioctylfluorene-alt-benzothiadiazole) (F8BT) single nanoparticles and either poly(9,9- dioctylfluorene - co - bis-N,N- (4 -butylphenyl)-bis-N,N-phenyl-1,4-phenylene diamine) (PFB) or poly(9,9-dioctylfluorene-co-N-(4-butylphenyl)diphenylamine) (TFB) film in model photovoltaic devices was also investigated. A wide distribution of exciton dissociation yields was observed from each nanodomain due to the device geometry. The observed hysteresis in fluorescence voltage curve was ascribed to accumulated charges following charge separations. The dynamics of charge separation under the applied electric field was described in more detail. / text