In the field of applied electromagnetics, there is always a need to create new methods for electrical characterization of materials, systems, devices, etc. Many applications need small and/or inexpensive equipment in performing these characterizations. The current method for making measurements of electrical properties at frequencies above 300 MHz, the transmission/reflection method, has severe limitations in these areas due large size and high price of the necessary equipment for making them. Therefore, presented herein is the conceptualization, design and analysis of a complex reflection coefficient detector which is relatively small, lightweight, and inexpensive. A reflection coefficient detector is a device designed to isolate and compare a driving signal against a reflected signal. The reflection of the second signal is caused by a mismatch between the device's output impedance and a load's input impedance. By comparing the driving, or transmitted, signal and the reflected signal, the reflection coefficient at the boundary can be calculated. This coefficient can be used to calculate a load's input impedance, or a material's permittivity when combined with an attached probe's characteristics. The reflection coefficient detector presented is built using microstrip and surface mount components. This makes the device comparably cheap. Its design is based upon five Wilkinson Power Dividers which lends itself to be scaled down for implementation in on-chip, and other micro- and nano- scale systems. The accuracy and functionality of the device will be demonstrated through the use of S-Parameters measurements and CAD simulations. Through this, it will be shown that the device is a practical form of making measurements in applications which are otherwise restricted to certain limitations. In closing, applications, alternative designs and future advancements of the complex reflection coefficient detector will be discussed.

京都大学 / 新制・課程博士 / 博士(工学) / 甲第23206号 / 工博第4850号 / 新制||工||1757(附属図書館) / 京都大学大学院工学研究科電気工学専攻 / (主査)教授 篠原 真毅, 教授 和田 修己, 教授 山本 衛 / 学位規則第4条第1項該当 / Doctor of Philosophy (Engineering) / Kyoto University / DFAM

Several microwave devices and antennas that are based on negative-refractive-index transmission-line (NRI-TL) metamaterials are presented in this thesis, which exhibit superior performance features compared to their conventional counterparts. These are a Wilkinson balun, a 1:4 series power divider, a four-element printed dipole array, a leaky-wave antenna, and an electrically small folded-monopole antenna. The Wilkinson balun employs +90° and −90° NRI-TL metamaterial lines at the output branches of a Wilkinson divider, to achieve a six-fold increase in the measured differential output phase bandwidth compared to that of an analogous balun employing transmission lines, while occupying only 55% of the area. The 1:4 series power divider comprises four non-radiating 0° NRI-TL metamaterial lines, each with a compact length of λ0/8, to provide equal power split to all four output ports. Compared to a conventional series power divider employing one-wavelength long transmission lines, the metamaterial divider provides a 154% increase in the measured through-power bandwidth, while occupying only 54% of the area. The metamaterial series power dividing concept is also applied to a four-element fully-printed dipole array that is designed to radiate at broadside, in order to demonstrate that the array exhibits reduced beam squinting characteristics. It is shown that the metamaterial-fed array has a measured scan-angle bandwidth that is 173% greater than an array that is fed using a conventional low-pass loaded line. The reduced-beam squinting property that NRI-TL metamaterial lines offer is subsequently exploited to create a leaky-wave antenna that radiates a near-fixed beam in the forward +45° direction, with an average measured beam squint of only 0.031°/MHz. This is achieved by operating the antenna in the upper right-handed band where the phase and group velocities are the closest to the speed of light. Finally, an electrically small antenna comprising four 0° NRI-TL metamaterial unit cells is presented which supports a predominantly even-mode current, thus enabling it to be modeled as a multi-arm folded monopole. This significantly increases its radiation resistance, which allows it to be matched to 50 Ω, while maintaining a high measured efficiency of 70%.

Several microwave devices and antennas that are based on negative-refractive-index transmission-line (NRI-TL) metamaterials are presented in this thesis, which exhibit superior performance features compared to their conventional counterparts. These are a Wilkinson balun, a 1:4 series power divider, a four-element printed dipole array, a leaky-wave antenna, and an electrically small folded-monopole antenna. The Wilkinson balun employs +90° and −90° NRI-TL metamaterial lines at the output branches of a Wilkinson divider, to achieve a six-fold increase in the measured differential output phase bandwidth compared to that of an analogous balun employing transmission lines, while occupying only 55% of the area. The 1:4 series power divider comprises four non-radiating 0° NRI-TL metamaterial lines, each with a compact length of λ0/8, to provide equal power split to all four output ports. Compared to a conventional series power divider employing one-wavelength long transmission lines, the metamaterial divider provides a 154% increase in the measured through-power bandwidth, while occupying only 54% of the area. The metamaterial series power dividing concept is also applied to a four-element fully-printed dipole array that is designed to radiate at broadside, in order to demonstrate that the array exhibits reduced beam squinting characteristics. It is shown that the metamaterial-fed array has a measured scan-angle bandwidth that is 173% greater than an array that is fed using a conventional low-pass loaded line. The reduced-beam squinting property that NRI-TL metamaterial lines offer is subsequently exploited to create a leaky-wave antenna that radiates a near-fixed beam in the forward +45° direction, with an average measured beam squint of only 0.031°/MHz. This is achieved by operating the antenna in the upper right-handed band where the phase and group velocities are the closest to the speed of light. Finally, an electrically small antenna comprising four 0° NRI-TL metamaterial unit cells is presented which supports a predominantly even-mode current, thus enabling it to be modeled as a multi-arm folded monopole. This significantly increases its radiation resistance, which allows it to be matched to 50 Ω, while maintaining a high measured efficiency of 70%.

This thesis reports the analysis of the rectangular shaped defected ground structure (RS-DGS) and the application of the structure on some microwave devices. DGS is analyzed in terms of its superior properties, which enables the designers to easily realize many kind of microwave devices which are impossible to achieve with the standard applications. Within the scope of this thesis, the focus is on the rectangular shaped DGS and its characteristic properties. The basic slow wave and high impedance characteristics are utilized in the design of some microwave devices. The design is carried on at the two different frequency bands: X-band and Ka band, centering at 10 GHz and 35 GHz, respectively. Finally, using the high impedance property and the coupling between the defects, a wide band 1 : 4 beam forming network is designed and implemented at 10 GHz.

Mixed-signal processing systems especially data converters can be reliably tested at high frequencies using on-chip testing schemes based on memory. In this thesis, an on-chip testing strategy based on shift registers/memory (2 k bits) has been proposed for digital-to-analog converters (DACs) operating at 5 GHz. The proposed design uses word length of 8 bits in order to test DAC at high speed of 5 GHz. The proposed testing strategy has been designed in standard 65 nm CMOS technology with additional requirement of 1-V supply. This design has been implemented using Cadence IC design environment. The additional advantage of the proposed testing strategy is that it requires lower number of I/O pins and avoids the large number of high speed I/O pads. It therefore also solves the problem of the bandwidth limitation that is associated with I/O transmission paths. The design of the on-chip tester based on memory contains no analog block and is implemented entirely in digital domain. In the proposed design, low frequency of 1 MHz has been used outside the chip to load the data into the memory during the write mode. During the read mode, the frequency of 625 MHz is used to read the data from the memory. A multiplexing system is used to reuse the stored data during read mode to test the intended functionality and performance. In order to convert the parallel data into serial data at high frequency at the memory output, serializer has been used. By using the frequencies of 1.25 GHz and 2.5 GHz, the serializer speeds up the data from the lower frequency of 625 MHz to the highest frequency of 5 GHz in order to test DAC at 5 GHz.

L’objectif de cette thèse a été premièrement de réaliser des dispositifs passifs intégrés à base de lignes à onde lentes nommées S-CPW (pour « Slow-wave CoPlanar Waveguide ») aux fréquences millimétriques. Plusieurs technologies CMOS ou BiCMOS ont été utilisées: CMOS 65 nm et 28 nm ainsi que BiCMOS 55 nm. Deux baluns, le premier basé sur une topologie de rat-race et le second basé sur un diviseur de puissance de Wilkinson modifié, ainsi qu’un inverseur de phase, ont été réalisés et mesurés dans la technologie CMOS 65 nm. Les résultats expérimentaux obtenus se situent à l’état de l’art en termes de performances électriques. Un coupler hybride et un diviseur de puissance avec des sorties en phase sans isolation ont été conçus en technologie CMOS 28 nm. Les simulations montrent de très bonnes performances pour des dispositifs compacts. Les circuits sont en cours de fabrication et pourront très bientôt être caractérisés. Ensuite, une nouvelle topologie de diviseurs de puissance, avec sorties en phase et isolé a été développée, offrant une grande flexibilité et compacité en comparaison des diviseurs de puissance traditionnels. Cette topologie est parfaitement adaptée pour les technologies silicium. Comme preuve de concept, deux diviseurs de puissance avec des caractéristiques différentes ont été réalisés en technologie PCB microruban à la fréquence de 2.45 GHz. Un composent a été conçu à 60 GHz en technologie BiCMOS 55 nm utilisant des lignes S CPW. Les simulations prouvent que le dispositif est faibles pertes, adapté et isolé. Les circuits sont également en cours de fabrication. Enfin, deux topologies de « reflection type phase shifter » ont été développées, la première dans la bande RF et la seconde aux fréquences millimétrique. Pour la bande RF, le déphasage atteint plus de 360° avec une figure de mérite très élevée en comparaison avec l’état de l’art. En ce qui concerne le déphaseur dans la bande millimétrique, la simulation montre un déphasage de 341° avec également une figure de mérite élevée. / The first purpose of this work was the use of slow-wave coplanar waveguides (S CPW) to achieve various passive components with the aim to show their great potential and interest at millimetre-waves. Several CMOS or BiCMOS technologies were used: CMOS 65 nm and 28 nm, and BiCMOS 55 nm. Two baluns, one based on a rat-race topology and the other based on a modified Wilkinson power divider, and a phase inverter, were achieved and measured in a 65 nm CMOS technology. State-of-the-art results were achieved. A branch-line coupler and an in phase power divider without isolation were designed in a 28 nm CMOS technology. Really good performances are expected for these compact devices being yet under fabrication. Then, a new topology of in phase and isolated power divider was developed, leading to more flexibility and compactness, well suited to millimetre-wave frequencies. Two power dividers with different characteristics were realized in a PCB technology at 2.45 GHz by using microstrip lines, as a proof-of-concept. After that, a power divider was designed at the working frequency of 60 GHz in the 55 nm BiCMOS technology with S CPWs. The simulation results showed a low loss, full-matched and isolated component, which is also under fabrication and will be characterized as soon as possible. Finally, two new topologies of reflection type phase shifters were presented, one for the RF band and one for the millimetre-wave one. For the one in RF band, the phase shift can reach more than 360° with a great figure-of-merit as compared to the state-of-the-art. Concerning the phase shifter in the millimetre-wave band, the simulation results show a phase shift of 341° with also a high figure-of-merit.

Subject of this thesis is a modification of an existing arrangement junction which does not meet current traffic demands. The adjustment includes two lane roundabout road I/11,1/33 and I/35 near ČKD in Hradec Králové. The proposed solution is based on requirements of the regional office of Hradec Králové region. One part of the thesis includes the capacity assessment of the proposed amendments.

This thesis is oriented to a specific section of energetics concerned with detection and registration of time responses of fast overvoltages in high-voltage power networks. The first part of this text is information about measuring frequency response characteristics of CR-divider and calculation of typical signal distortion caused by transfer function of this divider. The design of anti-aliasing filter is also included. The second part of this thesis is oriented to selecting key features of a measuring instrument specialized for detecting and recording fast events in electrical power networks. A selection of optimal type of processor and also a choice of communication interfaces is included there as well. The last chapter prepares mathematical procedures for classification of typical fast events in electrical power network using artificial neural networks.

The diploma thesis deals with the design of the water divider near Prostějov on the Romže River. Divider flows will be transferred into the Hloučela River. Within the thesis, hydraulic calculations of the side spillway were solved according to Bürgel, Pavlosky, Engels, Musterle, Kunštátský, Hager and energy solution methods in the Microsoft Excel spreadsheet and by using the HEC-RAS program as well. The calculations were compared to each other. Geometry of the relief water divider on the Romže River and the related buildings was designed based on the performed calculations. The required function of the relief object is guaranteed by manipulation of designed sluice gate. The study includes the text part with the calculations and the drawing part documenting the implementation of the designed measures.