<p>Designing an application specific integrated circuit (ASIC) must be starting with careful preparations, otherwise the chip will not be as good as possible. The theoretical studies must cover everything from the chip circuits to the application structure. In mobile applications there is extremely important that the current consumption becomes minimized because the battery power is limited. The power reductions studies must include the most power costing circuits on the chip. When the whole circuit or segments of the circuit is not in use, they must switch fast and simple into another mode that consume nearly none power. This mode is called sleep-mode. If the sleep-mode has very low leakage currents, the lifetime of the application will dramatically increase. </p><p>This report studies the most power costing circuits in smartcard application ASIC. The chip should be used to control a LCD display on the smartcard. The circuits that have been investigated are level shifters, charge pumps and LCD drivers, also sleep-mode configuration possibilities have been investigated. Other small preparing work is also included in the thesis.</p>

Low power, high speed serial transceivers are employed in a wide range of applications ranging from chip-to-chip, backplane, and optical interconnects. Apart from being capable of handling a wide range of data rates, the transceivers should have low power consumption (mW/Gbps) and be fully integrated. This work discusses enabling techniques to implement such transceivers. Specifically, three designs: (1) a 0.5-4 Gbps serial link which uses current recycling to reduce power dissipation and (2) a 0.5-2.5 Gbps reference-less clock and data recovery circuit which uses a novel frequency detector to achieve unlimited acquisition range and (3) a 2-4 Gbps low power receiver architecture capable of resolving multiple signalling formats with a simplified XOR based phase rotating PLL will be presented. All the three circuit topologies are highly digital and aim to address the requirements of wide operating range, low power dissipation while being fully integrated. Measured results obtained from the prototypes illustrate the effectiveness of the proposed design techniques. / Graduation date: 2012 / Access restricted to the OSU Community at author's request from Dec. 2, 2011 - June 2, 2012

The objective of the proposed research is to investigate the design of Self-Aware Radio Frequency Circuits and Wireless Communication Systems that can adapt to environmental and process variations to always operate at minimum power levels possible, extending battery life. The explosive growth of portable battery operated devices has mandated design of low power circuits and systems to prolong battery life. These devices fabricated in modern nanoscale CMOS technologies suffer from severe process variation due to the reduced controllability of the fabrication process, causing yield loss. This calls for integrated low power and process tolerant design techniques, or design of systems that can adapt to its process and environment to maintain its performance while minimizing power consumption. Currently, most of the wireless circuits are designed to meet minimum quality-of-service requirements under worst-case wireless link conditions (interference, noise, multi-path effects), leading to high power consumption when the channel is better than worst-case. In this research, we develop a multi-dimensional adaptation approach for wireless transmitters and receivers that optimally trades-off power vs. performance across temporally changing operating conditions by concurrently tuning control parameters in the RF front end to lower power consumption. Tunable circuits (e.g. LNA) with built-in tuning knobs providing independent controllability of important specifications allow optimal adaptation. Process sensing using intelligent test and calibration facilitates yield improvement and the design of process tolerant environment adaptive systems. Low cost testing methodologies are developed for identification of the health of the wireless circuit/system. These are used in conjunction with tuning algorithms that tune a wireless system under process variation to meet performance specifications and recover yield loss. This testing and adaptation is performed once during the post manufacture test/tune phase to compensate for manufacturing variations. This can also be applied periodically during in field operation of a device to account for performance degradation due to ageing. Finally, process tolerant environment adaptive systems are designed.

The main objective of this research is to improve the energy efficiency of low throughput wireless biomedical systems by employing digital design techniques. The power consumed in conventional wireless EEG (biomedical) systems is dominated by digital microcontroller and the radio frequency (RF) transceiver. To reduce the power associated with the digital processor, data compression can reduce the volume of data transmitted. An adaptive data compression algorithm has been proposed to ensure accurate representations of critical epileptic signals, while also preserving the overall power. Further advances in power reduction are also presented by designing a custom baseband processor for data compression. A functional system has been hardware verified and ASIC optimized to reduce the power by over 9X compared to existing methods. The optimized processor can operate at 32MHz with a near threshold supply of 0.5V in a conventional 45nm technology. While attempting to reach high frequencies in the near threshold regime, the probability of timing violations can reduce the robustness of the system. To further optimize the implementation, a low voltage clock tree design has been investigated to improve the reliability of the digital processor. By implementing the proposed clock tree design methodology, the digital processor can improve its robustness (by reducing the probability of timing violations) while reducing the overall power by more than 5 percent. Future work suggests examining new architectures for low-throughput processing and investigating the proposed systems' potential for a multi-channel EEG implementation.

The main objective of this thesis is to design reliable clock-distribution networks and power-delivery networks for three-dimensional integrated circuits (3D ICs) using through-silicon vias (TSVs). This dissertation supports this goal by addressing six research topics. The first four works focus on 3D clock tree synthesis for low power, pre-bond testability, TSV-induced obstacle avoidance, and TSV utilization. The last two works develop modeling approaches for reliability analysis on 3D power-delivery networks. In the first work, a clock synthesis algorithm is developed for low-power and low-slew 3D clock network design. The impact of various design parameters on clock performance, including the wirelength, clock power, clock slew, and skew, is investigated. These parameters cover the TSV count, TSV parasitics, the maximum loading capacitance of the clock buffers, and the supply voltage. In the second work, a clock synthesis algorithm is developed to construct 3D clock networks for both pre-bond testability and post-bond operability. Pre-bond testing of 3D stacked ICs involves testing each individual die before bonding, which can improve the overall yield of 3D ICs by avoiding stacking defective dies with good ones. Two key techniques including TSV-buffer insertion and redundant tree generation are implemented to minimize clock skew and ensure pre-bond testing. The impact of TSV utilization and TSV parasitics on clock power is also investigated. In the third work, an obstacle-aware clock tree synthesis method is presented for through-silicon-via (TSV)-based 3D ICs. A unique aspect of this problem lies in the fact that various types of TSVs become obstacles during 3D clock routing including signal, power/ground, and clock TSVs. These TSVs may occupy silicon area or routing layers. The generated clock tree does not sacrifice wirelength or clock power too much and avoids TSV-induced obstacles. In the fourth work, a decision-tree-based clock synthesis (DTCS) method is developed for low-power 3D clock network design, where TSVs form a regular 2D array. This TSV array style is shown to be more manufacturable and practical than layouts with TSVs located at irregular spots. The DTCS method explores the entire solution space for the best TSV array utilization in terms of low power. Close-to-optimal solutions can be found for power efficiency with skew minimization in short runtime. In the fifth work, current crowding and its impact on 3D power grid integrity is investigated. Due to the geometry of TSVs and connections to the global power grid, significant current crowding can occur. The current density distribution within a TSV and its connections to the global power grid is explored. A simple TSV model is implemented to obtain current density distributions within a TSV and its local environment. This model is checked for accuracy by comparing with identical models simulated using finite element modeling methods. The simple TSV models are integrated with the global power wires for detailed chip-scale power analysis. In the sixth work, a comprehensive multi-physics modeling approach is developed to analyze electromigration (EM) in TSV-based 3D connections. Since a TSV has regions of high current density, grain boundaries play a significant role in EM dominating atomic transport. The transient analysis is performed on atomic transport including grain and grain boundary structures. The evolution of atomic depletion and accumulation is simulated due to current crowding. And the TSV resistance change is modeled.

Wireless sensor networks are becoming important in several monitoring and sensing applications. Ultra low power consumption in the sensor nodes is important for extending the battery life of the nodes. In this dissertation, two low power BFSK receiver architectures are proposed and verified with prototype implementations in silicion. A 2.4 GHz 1 Mb/s polyphase filter (PPF) BFSK receiver demonstrates ±180 ppm frequency offset tolerance (FOT) and 40 dB adjacent channel rejection (ACR) at a modulation index (MI) of 2, with a power consumption of 1.9 mW. High FOT at low MI is achieved by a frequency-to-energy conversion architecture using PPFs without any frequency correction. The proposed hybrid topology of the PPF provides an improved ACR at reduced power. To further improve the energy efficiency, a low energy 900 MHz mixer-less BFSK receiver is designed. High gain frequency-to-amplitude conversion and better sensitivity is achieved by a linear amplifier with Q-enhanced LC tank, eliminating the need for local oscillators and mixers. With a power consumption of 500 μW, the receiver achieves sensitivities of -90 dBm and -76 dBm for data rates of 0.5 Mb/s and 6 Mb/s, respectively. The energy efficiency is 80 pJ/b when operating at 6 Mb/s. / Graduation date: 2013 / Access restricted to the OSU Community at author's request from March 25, 2013 - March 25, 2014

Real world is analog but the processing of signals can best be done in digital domain. So the need for Analog to Digital Converters(ADCs) is ever rising as more and more applications set in. With the advent of mobile technology, power in electronic equipment is being driven down to get more battery life. Because of their ubiquitous nature, ADCs are prime blocks in the signal chain in which power is intended to be reduced. In this thesis, four techniques to reduce power in high speed pipelined ADCs have been proposed. The first is a capacitor and opamp sharing technique that reduces the load on the first stage opamp by three fold. The second is a capacitor reset technique that aids removing the sample and hold block to reduce power. The third is a modified MDAC which can take rail-to-rail input swing to get an extra bit thus getting rid of a power hungry opamp. The fourth is a hybrid architecture which makes use of an asynchronous SAR ADC as the backend of a pipelined ADC to save power. Measurement and simulation results that prove the efficiency of the proposed techniques are presented. / Graduation date: 2009

Die Weiterentwicklung klassischer, elektronischer Identifikationstechnologien leistet einen wichtigen Beitrag zum technischen Fortschritt in Industrie, Logistik und Gesundheitswesen. Die vorliegende Dissertationsschrift beschreibt die Entwicklung eines Dual-Feed-Antennendesigns für passive UHF-RFID-Transponder auf kritischen Oberflächen. Die zu Grunde liegende Antennenstruktur besteht aus einem Microstrip-Patch unter Verwendung eines verlustarmen Substratmaterials. Dieser erfährt eine Optimierung hinsichtlich seiner Lesereichweite, insbesondere auf kritischen Oberflächen. Ein Zwei-Port-Konzept mit gekoppeltem Feed-Line-Anpassnetzwerk reduziert die Anzahl benötigter, diskreter Komponenten und ermöglicht eine kostengünstige Herstellung mittels klassischer Ätzverfahren. Verschiedene Ansätze zur Modellierung und zur analytischen Berechnung der Antennenparameter werden dargestellt. Des Weiteren erfolgt eine Verifikation der Antennenstruktur anhand eines Konzepts für einen passiven Energy-Harvesting-RFID-Transponder, der zur Temperaturüberwachung in den genannten Branchen eingesetzt werden kann. Dieses Konzept schließt ein effizientes Energiemanagement mittels eines Ultra-Low-Power-Mikrocontrollers sowie Ansätze zur Energiegewinnung und -speicherung mit ein und stellt die Wahl wichtiger Systemparameter und Bauelemente anhand anwendungsspezifischer Abschätzungen dar.

En la dècada actual, l'augment del consum energètic dels circuits integrats està tenint un impacte cada vegada més important en el disseny electrònic. Segons l'informe de la Semiconductor Industry Association de l'any 1997, es preveu que aquest impacte serà encara major en la propera dècada. En la bibliografia existeixen diversos treballs on es relaciona un consumo energètic elevat amb la degradació de les prestacions i la fiabilitat del xip. Per aquesta raó, el consum energètic ha estat incorporat com a un altre paràmetre a tenir en compte en el disseny dels circuits integrats. Es coneix com a energia de transició l'energia consumida per un circuit combinacional CMOS quan es produeix un canvi en les seves entrades. Una energia de transició excessivament elevada pot afectar a la fiabilitat del xip a través dels anomenats hot spots, i de l'electromigració. Altres efectes com el ground bouncing i la signal integrity degradation poden repercutir en les prestacions del circuit. La minimització de les degradacions esmentades anteriorment requereixen de la caracterització de l'energia de transició màxima durant la fase de disseny. A tal efecte, en aquesta tesi es proposen dues metodologies que permeten l'estimació de l'energia de transició màxima en circuits combinacionals CMOS. Donat que l'estimació del nivell màxim exacte es inviable en circuits a partir de mides mitjanes, es proposa el càlcul de dues cotes, una d'inferior i una altra de superior, que delimiten un interval de localització de l'esmentat nivell màxim. La tesi està estructurada en els següents capítols. En el capítol 1 es fa una introducció al tema investigat en aquesta tesi i es presenten els treballs existents que el tracten. En el capítol 2 s'introdueixen els models d'estimació de l'energia de transició emprats més habitualment a nivell lògic, que és el nivell de disseny considerat en aquesta tesi. Aquests models assumeixen que l'únic mecanisme de consum és la commutació de les capacitats paràsites del circuit. En els capítols 3 i 4 es tracta l'estimació de l'energia de transició màxima. Aquesta estimació es realitza a partir del càlcul de dues cotes properes, una superior i una altre inferior, a aquesta energia màxima. En el capítol 5 es presenta l'anàlisi del comportament de l'activitat ponderada front als models de retard estàtics. Finalment, en el capítol 6 s'aborden les conclusions generals de la tesis i el treball futur. / El consumo energético de los circuitos integrados es un factor cuyo impacto en el diseño electrónico ha crecido significativamente en la década actual. Según el informe de la Semiconductor Industry Association del año 1997, se prevé que este impacto será aún mayor en la próxima década. En la bibliografía existen diversos trabajos donde se relaciona un consumo energético elevado con la degradación de las prestaciones y la fiabilidad del chip. Por esta razón, el consumo energético ha sido incorporado como otro parámetro a tener en cuenta en el diseño de los circuitos integrados. Se conoce como energía de transición la energía consumida por un circuito combinacional CMOS cuando se produce un cambio en las entradas del mismo. Una energía de transición excesivamente elevada puede afectar a la fiabilidad del chip a través de los hot spots, de la electromigración. Otros efectos como el ground bouncing y la signal integrity degradation pueden repercutir en las prestaciones del circuito. La minimización de las degradaciones mencionadas anteriormente requiere de la caracterización de la energía de transición máxima durante la fase de diseño. A este efecto, se propone en esta tesis dos metodologías que permiten la estimación de la energía de transición máxima en circuitos combinacionales CMOS. Dado que la estimación del nivel máximo exacto es inviable en circuitos a partir de tamaños medios, se propone el cálculo de dos cotas, una de inferior y otra de superior, que delimiten un intervalo de localización de dicho nivel máximo. La tesis está estructurada en los siguientes capítulos. En el capítulo 1 se presenta una introducción al tema investigado en esta tesis y se resumen los trabajos existentes más importantes. En el capítulo 2 se introducen los modelos de estimación de la energía de transición más comúnmente utilizados a nivel lógico, que es el nivel de diseño considerado en esta tesis. Estos modelos asumen que el único mecanismo de consumo es la conmutación de las capacidades parásitas del circuito. En los capítulos 3 y 4 se aborda la estimación de la energía de transición máxima. Esta estimación se realiza a partir del cálculo de dos cotas cercanas, una superior y una inferior, a esta energía máxima. En el capítulo 5 se presenta el análisis del comportamiento de la actividad ponderada frente a los modelos de retardo estáticos. Finalmente, en el capítulo 6 se presentan las conclusiones generales de la tesis y el trabajo futuro. / The importance of the energy consumption on the design of electronic circuits has increased significantly during the last decade. According to the report of the Semiconductor Industry Association, of 1997, the impact in the next decade will be even greater. In the bibliography several works exist relating to the high energy consumption with the degradation of the reliability and performance of the xip. For this reason, the energy consumption has been included as another parameter to take into account during the design of integrated circuits. It is known as transition energy, the energy consumed by a CMOS combinational circuit when its inputs change their value. Excessively high transition energy may affect the reliability of the chip through the generation of hot spots and electromigration. Other effects such as ground bouncing and signal integrity degradation may reduce the performance of the circuit. In order to minimize the previously detected bad effects it is useful to characterize the maximum transition energy, during the design phase. To this objective, this thesis presents two methodologies that allow for the estimation of the maximum transition energy in CMOS combinational circuits. Given that the estimation of the maximum level is only attainable for medium size circuits, it is proposed the calculation of bounds (higher and lower) delimiting the interval where the maximum level is located. The thesis is divided into the following chapters. In chapter 1 an introduction to the topic and a review of the previous works related to this research domain is given. In chapter 2 the models most extended for the estimation of the transition energy are presented. These models are mainly used at logic level which is the level assumed in this thesis. They assume that the switching of the parasitic capacitances is the only mechanism producing energy consumption. In chapters 3 and 4 the estimation of the maximum transition energy is considered. This estimation is made from the calculation of an upper and lower bound to this maximum transition energy. In chapter 5 the analysis of the switching activity is made for different static delay models. Finally, in chapter 6 the general conclusions of the thesis and future work are discussed.

CDMA channel selection requires sharp as well as wide-band Filtering. SAW Filters which have been used for this purpose are only available in IF range. In direct conversion receivers this has to be done at low frequencies. Switched Capacitor technique has been employed to design a low power, highly selective low-pass channel select Filter for CDMA wireless receivers. The topology which has been chosen ensures the low sensitivity of the Filter response. The circuit has been designed in a mixed-mode 0. 18u CMOS technology working with a single supply of 1. 8 V while its current consumption is less than 10 mA.