The interaction of an HVDC converter with the connected power system is of complex nature. An accurate model of the converter is required to study these interactions. The use of analytical small-signal converter models provides useful insight and understanding of the interaction of the HVDC system and the connected system components. In this thesis analytical models of the HVDC converters are developed in the frequency-domain by calculating different transfer functions for small superimposed oscillations of voltage, current, and control signals. The objective is to study the dynamic proprieties of the combined AC-DC interaction and the interaction between different HVDC converters with small signal analysis. It is well known that the classical Bode/Nyquist/Nichols control theory provides a good tool for this purpose if transfer functions that thoroughly describe the 'plant' or the 'process' are available. Thus, there is a need for such a frequency-domain model. Experience and theoretical calculation have shown that voltage/power stability is a very important issue for an HVDC transmission link based on conventional line-commutated thyristor-controlled converters connected to an AC system with low short circuit capacity. The lower the short circuit capacity of the connected AC system as compared with the power rating of the HVDC converter, the more problems related to voltage/power stability are expected. Low-order harmonic resonance is another issue of concern when line-commutated HVDC converters are connected to a weak AC system. This resonance appears due to the presence of filters and shunt capacitors together with the AC network impedance. With a weak AC system connected to the HVDC converter, the system impedances interact through the converter and create resonances on both the AC- and DC-sides of the converter. In general, these resonance conditions may impose limitations on the design of the HVDC controllers. In order to improve the performance of the HVDC transmission system when it is connected to a weak AC system network, a reactive compensator with a voltage source converter has been closely connected to the inverter bus. In this thesis it is shown that the voltage source converter, with an appropriate control strategy, will behave like a rotating synchronous condenser and can be used in a similar way for the dynamic compensation of power transmission systems, providing voltage support and increasing the transient stability of the converter. / QC 20100708

In this thesis, a new HVDC-based converter system for wind farms is investigated. It is based on a mutually commutated soft-switching converter system and provides a unique integrated solution for the wind turbine generator drive systems, the wind turbine interconnection, and the power conversion for HVDC transmission. In a wind farm, the mutually commutated converter system is a distributed system. A medium-frequency collection grid connects the converter station, equipped with a single-phase voltage source converter and a medium-frequency transmission transformer, with the wind turbines, each containing a cycloconverter and a medium-frequency distribution transformer. In this thesis, various system aspects regarding the application of a distributed mutually commutated converter system in a wind farm are investigated. Special attention is paid to the design of a medium-frequency collection grid that has an acceptable level of transient overvoltages, the design of medium-frequency transformers with suitable magnetic, electric and thermal properties, and the development of a strategy to commutate the voltage source converter during low power generation. In order to adapt the mutually commutated converter system for an application in a wind farm, it had to be further developped. Different carrier-based and space-vector oriented modulation methods have been investigated. It turns out that for any load angle there is a quasi-discontinuous pulse width modulation strategy that can produce the same pulse patterns as space vector modulation. In addition, a modulation strategy has been developed that allows to replace the IGBTs in the cycloconverter with cheap, robust, and reliable fast thyristors, despite their absence of turn-off capability. The feasibility of different modulation strategies for mutually commutated converter systems has been verified on a down-scaled prototype converter system with both IGBT- and thyristor-based cycloconverters. Finally, a feasible wind farm layout is proposed, which considerably reduces the energy generation costs for large winds farms distant to a strong grid connection point. As a consequence, the proposed solution may facilitate the establishment of remotely located wind farms. / QC 20100802

Static synchronous compensation (StatCom) is an application that utilizes a voltage source converter (VSC) to provide instantaneous reactive power support to the connected power system. Conventionally, StatComs are employed for reactive power support only. However, with the integration of energy storage (ES) into a StatCom, it can provide active power support in addition to the reactive power support. This thesis deals with the integration of ES into StatComs. The investigation involves the following aspects: possible benefits for power systems, main circuit design, and control strategies. As the basis of the investigation, a control scheme is proposed for two-level VSCs. It is a novel flux modulation scheme combined with the well-known deadbeat current control. The current controller is capable of controlling the positive sequence, the negative sequence, and the offset components of the converter current. With flux modulation, all the three above-mentioned components of the bus flux are controllable. This differs from the conventional voltage modulation scheme, in which only the positive and negative sequence components of the bus voltage are controllable. The difference between the proposed flux modulation scheme and the voltage modulation scheme is investigated regarding saturation of transformers in the connected system during fault recovery. The investigation shows that by controlling the offset component of the bus flux, the transformer saturation problem can be mitigated to a certain extent. The possible benefits of the additional active power support of StatComs are investigated through several case studies. Different active power compensation schemes are proposed. First, active power compensation for sudden load changes in weak systems is investigated. The proposed control strategies are verified through computer simulations and through experiments in a real-time simulator. It is shown that with active power compensation, both the phase jumps and magnitude variations in the voltage at the PCC can be reduced significantly. Secondly, the power compensation of cyclic loads is investigated. The results show that the power quality at the connection point can be improved regarding both phase jumps and magnitude variations. In the third case study, the fault-recovery performance of an example system is investigated, showing that improved performance can be achieved by the additional active power support. ES devices such as capacitors, supercapacitors, and batteries exhibit considerable variation in the terminal voltage during a charging/discharging cycle. A direct connection of ES devices to the dc side of a VSC requires a higher voltage rating of the VSC. Thus, the cost of the VSC has to be increased. In this thesis, a dual thyristor converter topology is proposed to interface ES devices with the dc side of the VSC. First, a cost comparison is performed to compare the total cost of the whole system with and without the proposed interface topology. A cost comparison between various types of ES is also presented, providing a guideline for the choice of ES at energy levels where several alternatives exist. Then, the dynamics of systems with the proposed interface topology are investigated. Control strategies are proposed and verified by computer simulations. Two different control methods for the dual-thyristor converter are compared. / QC 20100819

Pulse width modulation (PWM) voltage source converters (VSC) are one type of motor drives that have become popular because they enable precise control of speed and torque in medium voltage motors. However, these drives are known to have adverse effects on the insulation system particularly on conductive armour tape (CAT) and semi-conductive stress grading tape (SGT). These tapes, which are crucial components of the insulation system, control the surface electrical stresses in the stator slot and in the end portion of the form-wound coils outside the grounded stator. The material properties of CAT and SGT and the methods by which they are applied on form-wound motor coils are traditionally designed for power frequency, or a 60 Hz sinusoidal voltage. However, because of the high frequencies associated with the repetition rate and the fast rise time of the PWM pulses, elevated electrical and thermal stresses develop in these tapes, which can lead to premature insulation failure. Little research has been conducted with respect to understanding the mechanism of dielectric heating as a function of frequency and repetitive pulse characteristics. The material characterization of CAT and SGT is a vital part of an investigation of the performance of the stress relief system at high frequencies. In this study, the anisotropic dielectric properties of CAT and SGT have been measured in dc and ac and in low and high electric fields. The laboratory experiments for determining the material characteristics are discussed and the results analyzed. According to the ac space charge limited field (SCLF) theory, the maximum ac tangential component of the electric field in a nonlinear resistive SGT on medium voltage form-wound motor coils can be predicted from the field dependent electrical conductivity and the frequency. However, the SCLF theory cannot predict the total electric field (vector sum of the tangential and normal components) in the air adjacent to the surface of the tapes. Simulations of the electric field using a finite element method (FEM), is one of the best ways of finding the resultant electric field distribution in the air space adjacent to the SGT. However, prior to this study, researchers simplified the modelling of the stress relief system to avoid the convergence problems that develop due to the nonlinearity of the SGT conductivity as a function of the electric field, and also because of the geometry and dimensions of the tapes when their depths are orders of magnitude smaller than the other dimensions associated with form-wound coils. For modelling the stress grading (SG) system at power frequency and at the rated voltage, the dc isotropic conductivity of the SGT and CAT has also been extensively investigated. However, relatively little work has been done with respect to the ac electrical behaviour of these materials and dc modelling cannot reflect the effects of high-frequency stresses on the machine insulation. In this study, comprehensive transient FEM modelling has been developed in order to simulate the insulation system with nonlinear field dependent materials. The actual dimensions of the components are applied in the model, and the appropriate material parameters for the FEM simulations are extracted from the experimental test results. One crucial point that has not been considered in previous studies is the effect of the component of the electric field that is normal to the surface of the coil. In most studies, only the tangential component of the electric field is considered; however, in this study, both components and the resultant electric field are computed. The surface tangential field is calculated with reference to the gradient of the surface potential as measured with an electrostatic voltmeter. It is shown that this technique can provide a reasonable estimate for the tangential field along the SG system, but not without limitations, which are discussed in detail. Based on laboratory work and analytical analysis, this research has successfully determined the relationship between the thermal effect of the PWM voltage and the other repetitive fast pulses, such as square wave and impulse voltages. The influence of the pulse characteristics on the development of stresses has also thoroughly investigated, and the results are presented. A coupled electric and thermal model that incorporates the finite element method (FEM) is used as a means of studying thermal stresses and determining appropriate remedies. However, using transient analysis as an approach for finding the temperature profile associated with high repetitive impulses (1-10 kHz) and fast rise times (~200 ns) is both difficult and impractical. According to these considerations, an alternative method has been developed from stationary analyses based on two sinusoidal voltages of different frequencies. The frequency and amplitude of these sinusoids are measured relative to the switching frequency, signal power, and nonlinearity of the system, and the results of the simulation are then verified experimentally, thus showing the efficacy of this method. This research also concluded that a capacitive SG system with conductive foil embedded in the groundwall insulation can be a practical alternative to a conventional SGT of form-wound coils in inverter fed motors. The performance of the capacitive SG scheme is independent of frequency and can therefore provide the required mitigation of the stress caused by repetitive fast pulses. The results of the evaluation of this system with respect to qualification tests demonstrate the effectiveness of the system.

Series Active Filters (SAF) are designed for harmonic isolation and load voltage regulation of single-phase and three-phase voltage harmonic source type nonlinear loads. The novel Absolute Value Method (AVM) for load voltage harmonic extraction is proposed and applied in the control algorithm of SAF. The SAF compensated systems are represented by simplified linear models such that SAF controller gains can be easily determined. Harmonic isolation and load voltage regulation performances of 2.5 kW single-phase and 10 kW three-phase SAF compensated systems are evaluated by detailed simulations. Laboratory prototype single-phase and three-phase SAFs and loads are designed and manufactured. Digital signal processor based control platform is employed. Exclusive laboratory tests are conducted. Via laboratory experiments and simulations it is shown that AVM yields superior harmonic isolation and load voltage regulation performance compared to the conventional low/high pass filtering method. Theory, simulations, and experiments are well correlated and illustrate the feasibility of the proposed method.

A voltage source inverter is commonly used to supply a variable frequency variable voltage to a three phase induction motor in a variable speed application. A suitable pulse width modulation (PWM) technique is employed to obtain the required output voltage in the line side of the inverter. Real-time methods for PWM generation can be broadly classified into triangle comparison based PWM (TCPWM) and space vector based PWM (SVPWM). In TCPWM methods such as sine-triangle PWM, three phase reference modulating signals are compared against a common triangular carrier to generate the PWM signals for the three phases. In SVPWM methods, a revolving reference voltage vector is provided as voltage reference instead of three phase modulating waves. The magnitude and frequency of the fundamental component in the line side are controlled by the magnitude and frequency, respectively, of the reference vector. The fundamental line side voltage is proportional to the reference magnitude during linear modulation. With sine-triangle PWM, the highest possible peak phase fundamental voltage is 0.5Vdc, where Vdc is the DC bus voltage, in the linear modulation zone. With techniques such as third harmonic injection PWM and space vector based PWM, the peak phase fundamental voltage can be as high as (formula) (i.e., 0:577Vdc)during linear modulation. To increase the line side voltage further, the operation of the VSI must be extended into the overmodulation region. The overmodulation region extends upto the six-step mode, which gives the highest possible ac voltage for a given (formula). In TCPWM based methods, increasing the reference magnitude beyond a certain level leads to pulse dropping, and gradually leads to six-step operation. However, in SVPWM methods, an overmodulation algorithm is required for controlling the line-side voltage during overmodulation and to achieve a smooth transition from PWM to six-step mode. Numerous overmodulation algorithms have been proposed in the literature for space vector modulated inverter. A well known algorithm among these divides the overmodulation zone into two zones, namely zone-I and zone-II. This is termed as the 'existing overmodulation algorithm' here. This algorithm is modified in the present work to reduce computational burden without much increase in the line current distortion. During overmodulation, the fundamental line side voltage and the reference magnitude are not proportional, which is undesirable from the control point of view. The present work ensures a linear relationship between the two. Apart from the fundamental component, the inverter output voltage mainly consists of harmonic components at high frequencies (around switching frequency and the integral multiples) during linear modulation. However, during overmodulation, low order harmonic components such as 5th, 7th, 11th, 13th etc., are also present in the output voltage. These low order harmonic voltages lead to low order harmonic currents in the motor. The sum of the lower order harmonic currents is termed as 'lower order current ripple'. The present thesis proposes a method for estimation of lower order current ripple in real-time. In closed loop current control, the motor current is fed back to the current controller. During overmodulation, the motor current contains low order harmonics, which appear in the current error fed to the controller. These harmonic currents are amplified by the current error amplifier deteriorating the performance of the drive. It is possible to filter the lower order harmonic currents before being fed back. However, filtering introduces delay in the current loop, and reduces the bandwidth even during linear modulation. In the present work, the estimated lower order current ripple is subtracted from the measured current before the latter is fed back to the controller. The estimation of lower order current ripple and the proposed current control are verified through simulation using MATLAB/SIMULINK and also experimentally on a laboratory prototype. The experimental setup comprises of a field programmable gate arrays (FPGA) based digital controller, an IGBT based inverter and a four-pole squirrel cage induction motor. (Pl refer the original document for formula)

Στην παρούσα διπλωματική εργασία γίνεται αναφορά στο ενεργειακό πρόβλημα, στις διάφορες μορφές ενέργειας, στα διάφορα είδη μετατροπέων και τα είδη ελέγχου. Πιο συγκεκριμένα, ασχολούμαστε με τον έλεγχο σε μετατροπείς από την πλευρά του δικτύου που χρησιμοποιούνται σε ανεμογεννήτριες. Επιπλέον, εξομοιώνουμε έναν μετατροπέα στη πλευρά του δικτύου για να ρυθμίσουμε τη DC τάση. Πιο συγκεκριμένα: Στο κεφάλαιο 1, θα ασχοληθούμε με το πρόβλημα ενέργειας και την αλλαγή στο κλίμα, τα οποία αποτελούν δύο από τα πιο βασικά προβλήματα του πλανήτη. Ακόμα, θα αναφερθούμε στις Ανανεώσιμες Πηγές Ενέργειας και κυρίως στην αιολική. Επίσης, θα γίνει μία μικρή αναφορά με βάση διαγράμματα για τους κανονισμούς που ισχύουν σε διάφορες χώρες της Ευρώπης όσον αφορά την λειτουργία Εγκαταστάσεων Αιολικής Ενέργειας. Στο κεφάλαιο 2, θα αναφερθούμε στις δομές μετατροπέων για διασύνδεση με ανεμογεννήτριες, καθώς επίσης και στον έλεγχο από την πλευρά της γεννήτριας. Τέλος, γίνεται μία μικρή αναφορά στον έλεγχο ισχύος. Στο κεφάλαιο 3, γίνεται αναφορά στον μετατροπέα πηγής- τάσηςVSC, στα φίλτρα δικτύου και στη διαμόρφωση. Στο κεφάλαιο 4, γίνεται αναφορά στον τριφασικό διπλό μετατροπέα τάσης, στη λειτουργία του, στο μοντέλο του καθώς και στις κατάλληλες εξισώσεις που χρησιμοποιούνται για τον έλεγχο του μετατροπέα. Στο κεφάλαιο 5, γίνεται περιγραφή του ελέγχου με διπλούς βρόγχους, γίνεται μία σύντομη αναφορά στο PLL και δίνονται οι κατάλληλες εξισώσεις. Επιπλέον, γίνεται μια σύντομη περιγραφή του μοντέλου που χρησιμοποιείται στη συγκεκριμένη διπλωματική. Στο κεφάλαιο 6, παρουσιάζουμε την εφαρμογή στο παρών μοντέλο καθώς και τα αποτελέσματα χρησιμοποιώντας το πρόγραμμα matlab/simulink, τις παραμέτρους καθώς επίσης και τις γραφικές παραστάσεις. / --

No description available.

Pulse width modulation (PWM) voltage source converters (VSC) are one type of motor drives that have become popular because they enable precise control of speed and torque in medium voltage motors. However, these drives are known to have adverse effects on the insulation system particularly on conductive armour tape (CAT) and semi-conductive stress grading tape (SGT). These tapes, which are crucial components of the insulation system, control the surface electrical stresses in the stator slot and in the end portion of the form-wound coils outside the grounded stator. The material properties of CAT and SGT and the methods by which they are applied on form-wound motor coils are traditionally designed for power frequency, or a 60 Hz sinusoidal voltage. However, because of the high frequencies associated with the repetition rate and the fast rise time of the PWM pulses, elevated electrical and thermal stresses develop in these tapes, which can lead to premature insulation failure. Little research has been conducted with respect to understanding the mechanism of dielectric heating as a function of frequency and repetitive pulse characteristics. The material characterization of CAT and SGT is a vital part of an investigation of the performance of the stress relief system at high frequencies. In this study, the anisotropic dielectric properties of CAT and SGT have been measured in dc and ac and in low and high electric fields. The laboratory experiments for determining the material characteristics are discussed and the results analyzed. According to the ac space charge limited field (SCLF) theory, the maximum ac tangential component of the electric field in a nonlinear resistive SGT on medium voltage form-wound motor coils can be predicted from the field dependent electrical conductivity and the frequency. However, the SCLF theory cannot predict the total electric field (vector sum of the tangential and normal components) in the air adjacent to the surface of the tapes. Simulations of the electric field using a finite element method (FEM), is one of the best ways of finding the resultant electric field distribution in the air space adjacent to the SGT. However, prior to this study, researchers simplified the modelling of the stress relief system to avoid the convergence problems that develop due to the nonlinearity of the SGT conductivity as a function of the electric field, and also because of the geometry and dimensions of the tapes when their depths are orders of magnitude smaller than the other dimensions associated with form-wound coils. For modelling the stress grading (SG) system at power frequency and at the rated voltage, the dc isotropic conductivity of the SGT and CAT has also been extensively investigated. However, relatively little work has been done with respect to the ac electrical behaviour of these materials and dc modelling cannot reflect the effects of high-frequency stresses on the machine insulation. In this study, comprehensive transient FEM modelling has been developed in order to simulate the insulation system with nonlinear field dependent materials. The actual dimensions of the components are applied in the model, and the appropriate material parameters for the FEM simulations are extracted from the experimental test results. One crucial point that has not been considered in previous studies is the effect of the component of the electric field that is normal to the surface of the coil. In most studies, only the tangential component of the electric field is considered; however, in this study, both components and the resultant electric field are computed. The surface tangential field is calculated with reference to the gradient of the surface potential as measured with an electrostatic voltmeter. It is shown that this technique can provide a reasonable estimate for the tangential field along the SG system, but not without limitations, which are discussed in detail. Based on laboratory work and analytical analysis, this research has successfully determined the relationship between the thermal effect of the PWM voltage and the other repetitive fast pulses, such as square wave and impulse voltages. The influence of the pulse characteristics on the development of stresses has also thoroughly investigated, and the results are presented. A coupled electric and thermal model that incorporates the finite element method (FEM) is used as a means of studying thermal stresses and determining appropriate remedies. However, using transient analysis as an approach for finding the temperature profile associated with high repetitive impulses (1-10 kHz) and fast rise times (~200 ns) is both difficult and impractical. According to these considerations, an alternative method has been developed from stationary analyses based on two sinusoidal voltages of different frequencies. The frequency and amplitude of these sinusoids are measured relative to the switching frequency, signal power, and nonlinearity of the system, and the results of the simulation are then verified experimentally, thus showing the efficacy of this method. This research also concluded that a capacitive SG system with conductive foil embedded in the groundwall insulation can be a practical alternative to a conventional SGT of form-wound coils in inverter fed motors. The performance of the capacitive SG scheme is independent of frequency and can therefore provide the required mitigation of the stress caused by repetitive fast pulses. The results of the evaluation of this system with respect to qualification tests demonstrate the effectiveness of the system.

Η διπλωματική εργασία που ακολουθεί περιγράφει την διαδικασία που εφαρμόσθηκε ώστε να κατασταθεί δυνατή η τροφοδοσία ενός RL φορτίου με τάση σταθερή σε μέτρο και σε συχνότητα, από μια συστοιχία κυττάρων καυσίμου. Η πειραματική διάταξη, που κατασκευάσθηκε ώστε να πραγματοποιηθεί αυτός ο στόχος, εκτός από την πηγή (κύτταρο καυσίμου) και το φορτίο αποτελείται και από έναν ΣΡ/ΣΡ (dc/dc) μετατροπέα ανύψωσης τάσης, έναν αντιστροφέα πηγής τάσης, έναν τριφασικό μετασχηματιστή, ένα φίλτρο LC, μια συσκευή επιλογής φορτίου και τέλος την ψηφιακή κάρτα με την οποία εκτελούνται οι απαραίτητοι έλεγχοι. Όταν αναφερόμαστε σε τεχνικές ελέγχου εννοούμε αρχικά τόσο την παραγωγή παλμών με την τεχνική της ημιτονοειδούς διαμόρφωσης εύρους παλμών (Sinusoidal Pulse Width Modulation-SPWM) για την τροφοδότηση του αντιστροφέα πηγής τάσης όσο και παλμών με την τεχνική της διαμόρφωσης εύρους παλμών (Pulse Width Modulation – PWM) για τον έλεγχο του ΣΡ/ΣΡ (dc/dc) μετατροπέα ανύψωσης τάσης. Οι παλμοί αυτοί παράγονται μέσω προγράμματος που αναπτύχθηκε στην πλατφόρμα του Labview. Σε δεύτερο επίπεδο εφαρμόζεται με την βοήθεια της ψηφιακής κάρτας και του μοντέλου ο ασαφής έλεγχος που έχει ως σκοπό την σταθεροποίηση της τάσης στο φορτίο. Για να διαπιστώσουμε ότι έχουμε εξασφαλίσει απρόσκοπτη τροφοδοσία του τριφασικού φορτίου από την ενέργεια του κυττάρου καυσίμου με μια τάση με μειωμένο αρμονικό περιεχόμενο και σταθερό πλάτος και συχνότητα, πραγματοποιήσαμε βηματική αλλαγή της τιμής του φορτίου και αλλαγή της τάσης εξόδου του κυττάρου καυσίμου ώστε να διαπιστώσουμε αν όντως ο ασαφής έλεγχος αναλαμβάνει να επαναφέρει τις επιθυμητές τιμές της τάσης στο φορτίο. Η διπλωματική εργασία διαρθρώνεται με τον εξής τρόπο: Στο κεφάλαιο 1 επιχειρούμε μια σύντομη περιγραφή των ανανεώσιμων πηγών ενέργειας που κυριαρχούν στον Ελλαδικό χώρο (ηλιακή, αιολική, υδροηλεκτρική, γεωθερμική και ενέργεια από βιομάζα) ενώ αναφερόμαστε εκτενώς στην τεχνολογία των κυττάρων καυσίμου. Στο κεφάλαιο 2 γίνεται εκτενής περιγραφή των συσκευών που αποτελούν το κύκλωμα ισχύος της πειραματικής διάταξης. Το κύκλωμα ισχύος αποτελείται αρχικά από το κύτταρο καυσίμου που αποτελεί την πηγή ενέργειας, τον ΣΡ/ΣΡ (dc/dc) μετατροπέα ανύψωσης τάσης και τον αντιστροφέα πηγής τάσης. Σε δεύτερο επίπεδο υπάρχει το LC φίλτρο προς περιορισμό των αρμονικών και ο τριφασικός μετασχηματιστής που ανυψώνει το επίπεδο τάσης στο επιθυμητό επίπεδο. Τέλος, υπάρχει ο τριφασικός ζυγός στον οποίο συνδέεται το φορτίο που αποτελεί και την τερματική συσκευή της πειραματικής διάταξης. Στο κεφάλαιο 3 γίνεται μια σύγκριση των διαθέσιμων ψηφιακών μεθόδων για την υλοποίηση των απαραίτητων ελέγχων ενώ έπειτα παρουσιάζονται θεωρητικά αυτοί οι έλεγχοι. Οι διαθέσιμες ψηφιακές μέθοδοι για την πραγματοποίηση των ελέγχων είναι ο μικροεπεξεργαστής ψηφιακού σήματος (Digital Signal Processor-DSP) και οι ψηφιακές κάρτες της εταιρίας Νational Ιnstruments οι οποίες και τελικά επιλέχθηκαν. Οι απαιτούμενοι έλεγχοι που πρέπει να εφαρμοσθούν στην πειραματική μας διάταξη είναι όπως ήδη αναφέραμε η παραγωγή παλμών με τις τεχνικές της ημιτονοειδούς διαμόρφωσης εύρους παλμών (SPWM) και διαμόρφωσης εύρους παλμών (PWM) όπως και ο ασαφής έλεγχος. Στο κεφάλαιο 4 παρουσιάζονται αναλυτικά όλες οι συσκευές της πειραματικής μας διάταξης με ιδιαίτερη αναφορά σε όσες κατασκευάστηκαν στο εργαστήριο (όπως ο ΣΡ/ΣΡ (dc/dc) μετατροπέας ανύψωσης τάσης ) ενώ γίνεται και επεξήγηση διάφορων πρακτικών προβλημάτων που ανέκυψαν κατά την χρησιμοποίηση τους (για παράδειγμα με τον τριφασικό μετασχηματιστή). Στο κεφάλαιο 5 παρουσιάζεται η διαδικασία ανάπτυξης στην πλατφόρμα του Labview του προγράμματος που υλοποιεί τους απαιτούμενους ελέγχους. Πραγματοποιείται λοιπόν μια αναλυτική παρουσίαση όλων των εργαλείων και των ρυθμίσεων τους που μας επέτρεψαν να φθάσουμε στο επιθυμητό αποτέλεσμα. Τέλος, στο κεφάλαιο 6 παρουσιάζονται τα πειραματικά αποτελέσματα και παραθέτουμε τα συμπεράσματα που προέκυψαν. Πιο αναλυτικά υπάρχει παράθεση γραφημάτων και μετρήσεων για το σύνολο της πειραματικής διάταξης ενώ δίνεται ιδιαίτερη προσοχή στην ανάδειξη της λειτουργίας του ελέγχου και του τρόπου που επιδρά στην διάταξη μας. Τέλος, γίνεται μια καταγραφή πιθανών επεκτάσεων αυτής της διπλωματικής εργασίας. / The thesis that follows, describes the procedure which we followed in order to be able to supply a RL load with the power produced by a fuel cell. The load’s voltage should have constant value and frequency. The experimental configuration which was constructed to help us fulfill our goal further from the fuel cell and the RL load, includes a dc dc boost converter, a voltage source inverter, a 3phase transformer, a LC filter, a device that electronically chooses the value of the load and finally the digital card which executes all the necessary controls. When we talk about controls, we refer firstly to the production of SPWM pulses which are used in order to control the voltage source inverter and to the production of PWM pulses which are needed by the dc dc boost converter. These pulses are produced with the aid of a model developed with Labview. In addition, with the use of our digital card and the model which we developed, we are capable of applying the fuzzy logic to our experimental configuration in order to stabilize the load’s voltage. To be certain that we have ensured the smooth supply of the RL load with the power produced by the fuel cell and a voltage signal of constant value and frequency and low harmonic content, we made step changes to the load’s value and alterations to the fuel cell’s output, in order to assure that the fuzzy logic takes charge of the duty to restore the desired voltage signal to the load. The thesis is organized in the following way: In chapter 1 we make a brief description of the renewable energy sources which dominate Greece (solar, wind, hydroelectric, geothermal and biomass energy) and we present extensively the applications of fuel cells. In chapter 2 we describe on a great scale all the devices which consist the power circuit of the experimental configuration . So, the power circuit consists of the fuel cell, which is our energy source, the dc dc boost converter and the voltage source inverter. Furthermore, we have a LC filter in order to limit the total harmonic distortion and a 3 phase transformer which increase the voltage to the desired level. Finally, we have a 3 phase load which is the terminal device of the experimental configuration. In chapter 3 we compare the available digital methods for performing the desired controls and afterwards we present them theoretically. The available digital methods, in order to accomplish the controls, are the Digital Signal Processor (DSP) and the digital cards constructed by National Instruments (is our final choice). The required controls that must be performed include, as we have already mentioned, the SPWM and PWM pulses and of course the fuzzy control. In chapter 4 we present extensively all the devices of our experimental configuration with a special reference to all the devices which were constructed in our lab (like the dc dc boost converter). We make also special reference to some practical problems that we encountered when we used the previous devices (par example with the 3 phase transformer). In chapter 5 we present the procedure in order to develop the Labview model which contains all the necessary controls. Thus, we make a detailed presentation of all the tools and the settings which allowed to us to fulfill our goal. In chapter 6 we present all the experimental results and the conclusions we drew. More specifically, we present graphs and measurements for every part of the experimental configuration and we give special attention in order to give prominence to the fuzzy controller’s impact. Finally, some possible extensions of this thesis are underlined.