This thesis is an effort to investigate the operation and the performanceof modular multilevel converters (M2Cs). Proven to be the most promisingtopology in high-voltage high-power applications, it is necessary to put aneffort in understanding the physical laws that govern the internal dynamicsof such converters, in order to design appropriate control methods. AlthoughM2Cs belong to the well-studied family of voltage-source converters (VSCs),and claim a modular structure, their control is significantly more complicatedcompared to two- or three-level VSCs, due to the fact that a much highernumber of switches and capacitors are needed in such a topology. This thesishighlights the important parameters that should be considered when designingthe control for an M2C, through analyzing its internal dynamics, and alsosuggests ways to control such converters ensuring stable operation withoutcompromising the performance of the converter.Special focus is given on ac motor-drive applications as they are very demandingand challenging for the converter performance. Interactions betweenthe internal dynamics and the dynamics of the driven motor are experimentallyinvestigated. The problem of operating the converter when connectedto a motor standing still is visited, even under the condition that a greatamount of torque and current are requested, in order to provide an idea forthe converter requirements under such conditions. Finally, an optimization ofthe converter operation is suggested in order to avoid overrating the convertercomponents in certain operation areas that this is possible.All analytical investigations presented in this thesis are confirmed by experimentalresults on a laboratory prototype converter, which was developedfor the purposes of this project. Experimental verification proves the validityof the theoretical investigations, as well as the correct performance of thecontrol methods developed during this project on a real, physical converter,hoping that the results of this thesis will be useful for large-scale implementations,in the mega- or even giga-watt power range. / Denna avhandling är ett försök att undersöka drift och egenskaper avmodulära multinivåomvandlare (M2C:er). Eftersom denna topologi anses varaden mest lovande inom högspänings-högeffekt-tillämpningar är, och somett underlag för att kunna formulera lämpliga styrmetoder, är det nödvändigtatt lägga kraft i att försöka förståde fysikaliska lagar som styr den inredynamiken i sådana omvandlare. Även om M2C:erna tillhör den välstuderadefamiljen av spänningsstyva omvandlare (VSC:er), och har en modulärstruktur, är deras reglering avsevärt mer komplicerad jämfört med två- ellertre-nivåomvandlare, eftersom ett mycket större antal switchar och kondensatorerär nödvändiga i en sådan topologi. Denna avhandling sätter fingretpå de parametrar som måste beaktas när man konstruerar regleringen för enM2C, genom att analysera den interna dynamiken, samt att föreslå sätt attstyra sådana omvandlare såatt stabil drift kan säkerställas utan att negativtpåverka prestanda.Ett speciellt fokus läggs på växelströmsmotordrifter eftersom de är särskiltutmanande vad gäller prestanda. Växelverkan mellan den interna dynamikenoch motorns dynamik undersöks experimentellt. Problemet att driva motornvid stillestånd behandlas även i fallet med hög ström och högt moment för atterhålla kunskap om kraven påomvandlaren i sådana fall. Slutligen föreslås enoptimering av omvandlarens drifttillstånd för att undvika överdimensioneringav omvandlarens komponenter i de fall detta är möjligt.Alla analytiska undersökningar som läggs fram i denna avhandling är bekräftadegenom experimentella resultat från en laboratorieomvandlare, somutvecklats inom ramen för detta arbete. Den experimentella verifieringen bevisargiltigheten av alla teoretiska undersökningar. Den visar också på demycket goda prestanda som de utvecklade styrmetoderna har vid drift aven verklig fysisk omvandlare. Förhoppningen är att resultaten från detta arbetekan komma till använding i storskaliga implementerinar i mega- ellergiga-wattklassen. / <p>QC 20141201</p>

Multilevel converters have become the direct accepted solution for high power converter applications. They are used in wide variety of power electronic applications like power transmission and distribution, electric motor drives, battery management and renewable energy management to name a few. For medium and high voltage motor drives, especially induction motor drives, the use of multilevel voltage source inverters have become indispensible. A high voltage multilevel inverter could be realized using low voltage switching devices which are easily available and are of low cost. A multilevel inverter generates voltage waveforms of very low harmonic distortion by switching between voltage levels of reasonably small amplitude differences. Thus the dv/dt of the output voltage waveform is small and hence the electromagnetic interference generated is less. Because of better quality output generation, the switching frequency of the multilevel inverters could be reduced to control the losses. Thus, a multilevel converter stands definitely a class apart in terms of performance from a conventional two-level inverter. Many multilevel inverter topologies for induction motor drives are available in the literature. The basic multilevel topologies are the neutral point clamped (NPC) inverter, flying capacitor (FC) inverter and the cascaded H-bridge (CHB) inverter. Various other hybrid multilevel topologies have been proposed by using the basic multilevel inverter topologies. It is also possible to obtain multilevel output by using conventional two-level inverters feeding an open-end winding induction motor from both sides. All the conventional multilevel voltage source inverters generate hexagonal (6 sided polygons) voltage space vector structures. When an inverter with hexagonal space vector structure is operated in the over modulation range, significant low order harmonics are generated in the phase voltage output. Over modulation operation is required for the full utilization of the available DC-link voltage and hence maximum power generation. Among the harmonics generated, the fifth and seventh harmonics are of significant magnitudes. These harmonics generate torque ripple in the motor output and are undesirable in high performance motor drive applications. The presence of these harmonics further creates problems in the closed loop current control of a motor, affecting the dynamic performance. Again, the harmonic currents generate losses in the stator windings. Therefore, in short, the presence of harmonic voltages in the inverter output is undesirable. Many methods have been proposed to eliminate or mitigate the effect of the harmonics. One solution is to operate the inverter at high switching frequency and thereby push the harmonics generated to high frequencies. The stator leakage inductance offers high impedance to the high frequency harmonics and thus the harmonic currents generated are negligible. But, high switching frequency brings switching losses and high electromagnetic interference generation in the drive system. And also, high switching frequency operation is effective only in the linear modulation range. Another solution is to use passive harmonic filters at the inverter output. For low order harmonics, the filter components would be bulky and costly. The loss created by the filters degrades the efficiency of the drive system as well. The presence of a filter also affects the dynamic performance of the drive system during closed loop operation. Special pulse width modulation (PWM) techniques like selective harmonic elimination (SHE) PWM can prevent the generation of a particular harmonic from the phase voltage output. The disadvantages of such schemes are limited modulation index, poor dynamic performance and extensive offline computations. An elegant harmonic elimination method is to generate a voltage space vector structure having more number of sides like a dodecagon (12 sided polygons) or an octadecagon (18 sided polygons) rather than a hexagon. Inverter topologies generating dodecagonal voltage space vector structure eliminate fifth and seventh order harmonics, represented as 6n 1; n = odd harmonics, from the phase voltages and hence from the motor phase currents, throughout the entire modulation range. The first harmonics appearing the phase voltage are the 11th and 13th harmonics. Another advantage is the increased linear modulation range of operation for a given DC-link voltage, because geometrically dodecagon is closer to circle than a hexagon. An octadecagonal structure eliminates the 11th and 13th harmonics as well from the phase voltage output. The harmonics present in the phase voltage are of the order 18n 1; n = 1; 2; 3; :::. Thus the total harmonics distortion (THD) of the phase voltage is further improved. The linear modulation range also gets enhanced compared to hexagonal and dodecagonal structures. Multilevel dodecagonal and octadecagonal space vector structures combines the advantages of both multilevel structure and dodecagonal and octadecagonal structure and hence are very attractive solutions for high performance induction motor drive schemes. Chapter 1 of this thesis introduces the multilevel in-verter topologies generating hexagonal, dodecagonal and octadecagonal voltage space vector structures. Inverter topologies generating multilevel dodecagonal and octadecago-nal voltage space vector structures have been proposed before but using multiple DC sources delivering active power. The presence of more than one DC source in the inverter topology makes the back to back operation (four-quadrant operation) of the drive system difficult. And also the drive system becomes more costly and bulky. This thesis proposes induction motor drive schemes generating multilevel dodecagonal and octadecagonal volt-age space vector structures using a single DC source. In Chapter 2, an induction motor drive scheme generating a six-concentric multilevel dodecagonal voltage space vector structure using a single DC source is proposed for an open-end winding induction motor. In the topology, two three-level inverters drive an open-end winding IM, one inverter from each side. DC-link of primary inverter is from a DC source (Vdc) which delivers the entire active power, whereas the secondary inverter DC-link is maintained by a capacitor at a voltage of 0:289Vdc, which is self-balanced during the inverter operation. The PWM scheme implemented ensures low switching frequency for primary inverter. Secondary inverter operates at a small DC-link voltage. Hence, switching losses are small for both primary and secondary inverters. An open-loop V/f scheme was used to test the topology and modulation scheme. In the work proposed in Chapter 3, the topology and modulation scheme used in the first work is modified for a star connected induction motor. Again, the scheme uses only a single DC source and generates a six-concentric multilevel space vector struc-ture. The power circuit topology is realized using a three-level flying capacitor (FC) inverter cascaded with an H-bridge (CHB). The capacitors in the CHB inverter are maintained at a voltage level of 0:1445Vdc. The FC inverter switches between volt-age levels of [Vdc; 0:5Vdc; 0] and the CHB inverter switches between voltage levels of [+01445Vdc; 0; 0:1445Vdc]. The PWM scheme generates a quasi-square waveform output from the FC inverter. This results in very few switchings of the FC inverter in a funda-mental cycle and hence the switching losses are controlled. The CHB inverter switches Ch. 0: at high frequency compared to the FC inverter and cancels the low order harmonics (6n 1; n = odd) generated by the FC inverter. Even though the CHB operates at higher switching frequency, the switchings are at low voltage thereby controlling the losses. The linear modulation range of operation is extended to 48:8Hz for a base frequency of 50Hz. An open-loop V/f scheme was used to test the topology and modulation scheme. In Chapter 4, a nine-concentric multilevel octadecagonal space vector structure is proposed for the first time, again using a single DC source. The circuit topology remains same as the work in Chapter 3, except that the CHB capacitor voltage is maintained at 0:1895Vdc. The 5th; 7th; 11th and 13th harmonics are eliminated from the phase voltage output. The linear modulation range is enhanced to 49:5Hz for a base speed of 50Hz. An open-loop V/f scheme and rotor field oriented control scheme were used to test the proposed drive system. All the proposed drive schemes have been extensively simulated and tested in hard-ware. Simulation was performed in MATLAB-SIMULINK environment. For implement-ing the inverter topology, SKM75GB12T4 IGBT modules were used. The control al-gorithms were implemented using a DSP (TI’s TMS320F28334) and an FPGA (Xilinx Spartan XC3S200). A 1kW , 415V , 4-pole induction motor was used for the experiment purpose. The above mentioned induction motor drive schemes generate phase voltage outputs in which the low order harmonics are absent. The linear modulation range is extended near to the base frequency of operation compared to hexagonal space vector structure. In the inverter topologies, the secondary inverters or the CHB inverters functions as harmonic filters and delivers zero active power. The primary inverter in the topologies switches at low frequency, reducing the power loss. Single DC source requirement brings down the cost of the system as well as permitting easy four-quadrant operation. This is also advantageous in battery operated systems like EV applications. With these features and advantages, the proposed drive schemes are suitable for high performance, medium voltage induction motor drive applications.

Submitted by Renata Lopes (renatasil82@gmail.com) on 2017-03-13T15:20:14Z No. of bitstreams: 1 salatieldecastrolobato.pdf: 51678452 bytes, checksum: 022776c88833a1e47901180ebd1f826b (MD5) / Approved for entry into archive by Adriana Oliveira (adriana.oliveira@ufjf.edu.br) on 2017-03-13T19:33:17Z (GMT) No. of bitstreams: 1 salatieldecastrolobato.pdf: 51678452 bytes, checksum: 022776c88833a1e47901180ebd1f826b (MD5) / Made available in DSpace on 2017-03-13T19:33:17Z (GMT). No. of bitstreams: 1 salatieldecastrolobato.pdf: 51678452 bytes, checksum: 022776c88833a1e47901180ebd1f826b (MD5) Previous issue date: 2016-11-07 / O objetivo geral desta dissertação é o aperfeiçoamento do projeto de uma nova fonte de corrente em desenvolvimento para o acelerador de partículas Sirius. A corrente da fonte é aplicada em magnetos de elevada indutância e são programadas para apresentar forma de onda com significativa componente senoidal em corrente contínua e em baixa frequência, de acordo com as características operacionais necessárias do Sirius. Para efeitos de estudo, a metodologia empregada consiste essencialmente em desacoplar a análise e o projeto do controle em um estágio regulador de tensão seguido de um estágio de síntese da corrente. Foram realizados ensaios em uma fonte em construção no Laboratório Nacional de Luz Síncroton e em um protótipo desenvolvido na UFJF. As principais contribuições descritas nesta dissertação são: i) atenuação da propagação de distúrbios de baixa frequência para a rede elétrica; ii) emprego de retificador de tensão controlado para regulação da tensão do barramento CC, melhoria do fator de potência e redução de componentes harmônicas. Os resultados experimentais evidenciam que as alterações de projeto propostas nesta dissertação apresentam grande potencial para melhorar o desempenho da fonte de corrente em termos da qualidade de energia elétrica e da sintetização de corrente senoidal no magneto do acelerador de partículas. / This work consists in the evaluation and improvement of a current source for a particle accelerator. The output current presents a DC sinusoidal waveform in low frequecy which flows through the windings of high inductance electromagnets. The methodology consists in separating the analysis and project of the control into two parts: a voltage regulator stage,followedbyacurrentsynthesisstage. Testswereperformedonacurrentsourceunder construction at the Brazilian Synchrotron Light Laboratory (LNLS) and on a prototype developed at UFJF. The work main contributions are: i) Attenuation of the low frequency disturbances on the electrical grid; ii) Use of a controlled rectifier to regulate the voltage of the DC bus, improvement in power factor and reduction of harmonic components. The experimental results show that the proposed changes have potential in improving the performace of the current source in terms of its electric power quality and synthesis of sinusoidal current in the particule accelerator.

Submitted by Renata Lopes (renatasil82@gmail.com) on 2017-04-20T13:39:03Z No. of bitstreams: 1 pedromachadodealmeida.pdf: 13436160 bytes, checksum: 84c66613dade0766ae9ea2bdc8be9f91 (MD5) / Approved for entry into archive by Adriana Oliveira (adriana.oliveira@ufjf.edu.br) on 2017-04-20T14:45:37Z (GMT) No. of bitstreams: 1 pedromachadodealmeida.pdf: 13436160 bytes, checksum: 84c66613dade0766ae9ea2bdc8be9f91 (MD5) / Made available in DSpace on 2017-04-20T14:45:37Z (GMT). No. of bitstreams: 1 pedromachadodealmeida.pdf: 13436160 bytes, checksum: 84c66613dade0766ae9ea2bdc8be9f91 (MD5) Previous issue date: 2011-04-29 / Esta dissertação apresenta uma estratégia de controle para sistemas de geração fotovoltaicos, de único estágio, trifásicos, conectados à rede elétrica de distribuição. São desenvolvidos modelos matemáticos para representar as características dinâmicas dos painéis fotovoltaicos, do conversor fonte de tensão (VSC -“Voltage Source Converter”) e da rede de distribuição. A modelagem do sistema de geração disperso (SGD) é feita no sistema de coordenadas síncrono (dq), fornecendo um sistema de equações diferenciais que pode ser usado para descrever o comportamento dinâmico do sistema quando as tensões da rede estão equilibradas ou desequilibradas. O conversor é controlado no modo de corrente, através da estratégia de modulação vetorial (Space Vector Modulation - SVM). São projetadas duas malhas de controle em cascata para controlar o conversor estático. A malha interna controla a corrente injetada na rede enquanto que a externa controla a tensão no barramento CC do conversor. O controle da tensão CC permite rastrear o ponto de máxima potência do painel PV além de controlar a quantidade de potência ativa injetada na rede CA. Um método ativo de detecção de ilhamento baseado na injeção de corrente de sequência negativa é incorporado ao sistema de controle. Resultados de simulações digitais obtidos com o programa ATP (Alternative Transient Program ) são utilizados para validar os modelos matemáticos e as estratégias de controle. Finalmente, um protótipo experimental de pequena escala é montado em laboratório. Todo o sistema de controle do protótipo experimental foi implementado no DSP TMS320F28212. Os resultados obtidos demonstram o funcionamento do sistema e podem ser usados para validar a estratégia de controle utilizada. / This dissertation presents a control strategy for a single-stage, three-phase, photovoltaic systems to be connected to a distribution network. Mathematical models are developed to represent the dynamic characteristics of the photovoltaic panels, the voltage-source converter (VSC) and the distribution network. The modeling of the dispersed generation system (DGS) is done in the synchronous reference frame (dq), providing a system of differential equations that describes the dynamic behavior of the system when the network voltages are balanced or unbalanced. The converter is controlled in current mode through the space vector modulation (SVM) strategy. Two control loops are designed to control the static converter. The inner loop controls the injected current into the network while the external loop controls the converter DC bus voltage. The DC voltage regulator allows to track the PV maximum power point and to control the active power injected into the AC grid. An active islanding detection method based on negative-sequence current injection is incorporated into the control system. Digital simulations results obtained with Alternative Transients Program (ATP) is used to validate the mathematical models and the control strategies. Finally, a small-scale experimental prototype is implemented in the laboratory. The whole control system of the experimental prototype was programmed in DSP TMS320F2812 of Texas Instruments. The results demonstrate that the operation of the system can be used to validate the applied control strategy.

Die vorliegende Arbeit befasst sich mit einem detaillierten Vergleich von Mehrpunkt-Schaltungstopologien mit zentralem Gleichspannungszwischenkreis für den Einsatz in Mittelspannungsanwendungen. Im Rahmen dieser Untersuchungen wird die 3-Level Neutral Point Clamped Spannungswechselrichter Schaltungstopologie (3L-NPC VSC) sowohl mit Multilevel Flying Capacitor (FLC) als auch mit Multilevel Stacked Multicell (SMC) Schaltungstopologien verglichen, wobei unter Verwendung von aktuell verfügbaren IGBT-Modulen Stromrichterausgangsspannungen von 2.3 kV, 4.16 kV und 6.6 kV betrachtet werden. Neben der grundlegenden Funktionsweise wird die Auslegung der aktiven Leistungshalbleiter und der passiven Energiespeicher (Zwischenkreiskondensatoren, Flying Capacitors) für die untersuchten Stromrichtertopologien dargestellt. Unter Berücksichtigung verschiedener Modulationsverfahren und Schaltfrequenzen werden Kennwerte für den Oberschwingungsgehalt in der Ausgangsspannung und dem Ausgangsstrom vergleichend evaluiert. Die installierte Schalterleistungen, die Halbleiterausnutzungsfaktoren, die Stromrichterverlustleistungen sowie die Verlustleistungsverteilungen werden für die betrachteten Stromrichtertopologien detailliert gegenübergestellt und bewertet. / The thesis deals with a detailed comparison of voltage source converter topologies with a central dc-link energy storage device for medium voltage applications. The Three-Level Neutral Point Clamped Voltage Source Converter (3L-NPC VSC) is compared with multilevel Flying Capacitor (FLC) and Stacked Multicell (SMC) Voltage Source Converters (VSC) for output voltages of 2.3 kV, 4.16 kV and 6.6 kV by using state-of-the-art 6.5 kV, 3.3 kV, 4.5 kV and 1.7kV IGBTs. The fundamental functionality of the investigated converter topologies as well as the design of the power semiconductors and of the energy storage devices (Flying Capacitors and Dc-Link capacitors) is described. The installed switch power, converter losses, the semiconductor loss distribution, modulation strategies and the harmonic spectra are compared in detail.

Use of multilevel inverters are inevitable in medium and high voltage drives. This is due to the fact that the multilevel inverters can produce voltages in smaller steps which will reduce the harmonic content and result in more sinusoidal voltages and currents as compared to voltages and currents from two-level inverters. Due to the device limitations, use of two-level inverters is not possible in medium and high voltage drive applications. Though multiple devices can be connected both in series and parallel to achieve two-level operation, the output voltages still suffer from high harmonic content. Multilevel inverters have multiple DC voltage levels with switches that enable one of the voltage steps to be applied to the load. Due to decrease in step size during each switching instant, output voltages and currents of the multilevel inverters have considerably less harmonic content. As the number of levels increase, the switching step reduces thereby the harmonic content also reduces drastically. Due to their advantages, multilevel inverters have gained lot of acceptance in the industry even at lower voltages. The three main configurations that have gained popularity are the neutral point clamped converter, the flying capacitor converter and the cascaded H-bridge converter. Each converter has its own set of advantages and disadvantages. Based on the requirements of various applications, it is possible to fabricate hybrid multilevel topologies that are combinations of the three basic topologies. Researchers around the world have proposed several such converters for diverse applications so as to suit particular requirements like modularity, ease of control, improved reliability, fault tolerant capability etc. The present thesis explores multilevel converters with single DC link to be used for motor drive and grid connected applications. A novel five-level inverter topology formed by cascading a floating capacitor H-bridge module to a regular three-level flying capacitor inverter has been explored in chapter 2. The three-level flying capacitor inverter can generate pole voltages of 0, VDC /2 and VDC . By cascading it with another floating capacitor H-bridge of voltage magnitude VDC /4, pole voltages of 0, VDC /4, VDC/2, 3VDC /4 and VDC . Each of these pole voltage levels can have one or more switching combinations. However each switching combination has a unique effect on the state of the two capacitor voltages. By switching through redundant switching combinations for the same pole voltage, the two capacitors present in each phase can be balanced. The proposed topology also has an advantage that if one of the devices in the H-bridge fails, the topology can still be operated as a regular three-level flying capacitor inverter that can supply full load at rated power by bypassing the faulty H-bridge. This fault tolerant operation of the converter will enable it to be used in applications like traction and marine drives where high reliability is needed. The proposed converter needs a single DC link. All the required voltage levels can be generated from the single DC link. This enables back to back grid connected operation possible where multiple converters can interact with a single DC link. Various pole voltage switching combination and its effect on individual capacitor has been studied. A control algorithm to balance the capacitor voltages by switching through multiple redundancies for the same pole voltage has been developed. The proposed configuration has been implemented in hardware using IGBT H-bridge modules and the control circuitry is realized using DSP and FPGA. The performance of the drive is verified for various frequencies and modulation indices during steady state by running a three phase induction motor at no load. The stability of the drive during transients has been studied by accelerating the machine suddenly at no load and analyzing the performance of the drive. The capacitor voltages are made to deviate from their intended values and the capacitor balancing algorithm has been verified for its ability to bring the capacitor voltages back to their intended values. The experimental results have been presented and discussed in detail in the chapter 2. In the third chapter a common-mode voltage eliminated three-level inverter using a single DC link has been proposed. The power schematic is similar to the one presented in chapter 2. In this chapter the space vector polygon formed by the three phases of the proposed topology has been presented. The common-mode voltage generated by different pole voltage combinations for same space vector location and the redundant switching state combinations has been studied. The pole voltage combinations with zero common mode voltage have been studied. The switching state redundancies for the the pole voltage have been studied. The space vector polygon formed with the pole voltage combinations has been analyzed. A drive is made with the proposed common-mode voltage eliminated inverter. The performance of the drive is tested for various modulation indices and frequencies by running a three phase squirrel cage induction motor at no load. The transient performance is verified by accelerating the motor suddenly and checking the common-mode voltage along with the capacitor voltages. The results have been presented and discussed in detail in chapter 3. This converter has advantages like use of single DC supply, ability to operate as a regular three level converter in case of failure of one of the H-bridges. The work presented in fourth chapter proposes a novel three phase 17-level inverter configuration which utilizes a single DC supply. The rest of voltages are generated using three floating capacitor H-bridges. The redundant switching combinations for generating various pole voltages and their effect on the capacitors have been studied and suitable capacitor balancing algorithm has been developed. The proposed topology has been realized in hardware and the performance of the drive during steady state has been studied by running an induction motor at various modulation indices and frequencies. The transient response of the drive has been observed by accelerating the motor suddenly under no load. The results have been presented in detail in chapter four. This configuration also needs a single DC link. The advantages of this configuration is in case of failure of any devices in the H-bridge, the drive can be operated at reduced number of levels while supplying full load current. This feature helps the drive to be used in fault tolerant applications like marine and traction drives where reliability of the drive is of prime importance. All the topologies that have been presented in the previous chapters have mentioned about the usage of the proposed genre of topologies use single DC link and hence will enable back to back grid tied inverter connection. In the fifth chapter this has has been verified experimentally. The three phase squirrel cage induction motor is driven by using the seventeen-level inverter drive proposed in chapter four. A five-level active front-end is realized by the converter topology proposed in chapter two. The converter is run and the performance of the drive is studied at various modulation indices and speeds of the motor. Various aspects like re-generation operation, acceleration and other aspects of the drive have been studied experimentally and the results are presented in detail. For experimental setup, Semikron SKM75GB12T4 IGBT modules have been used to realize the power topology. These IGBTs are driven by M56972L drivers. The control circuit is realized using TMS320F2812 DSP along with Xilinx Spartan 3 FPGA (XC3S200) has been used. The voltages and currents are sensed using LEM LV-20P and LA 55-P hall effect based sensors.

For medium and high-voltage drive applications, multilevel inverters are very popular. It is due to their superior performance compared to 2-level inverters such as reduced harmonic content in the output voltage and current, lower common mode voltage and dv=dt, and lesser voltage stress on power switches. The popular circuit topologies for multilevel inverters are neutral point clamped, cascaded H-bridge and flying capacitor based circuits. There exist different combinations of these basic topologies to realize multilevel inverters with modularity, better fault tolerance, and reliability. Due to these advantages, multilevel converters are getting good acceptance from the industry, and researchers all over the world are continuously trying to improve the performance of these converters. To meet such demands, three multilevel inverter topologies are proposed in this thesis. These topologies can be used for high-power induction motor drives, and the concepts presented are also applicable for synchronous motor drives, grid-connected inverters, etc. To get nearly sinusoidal phase current waveforms, the switching frequency of the conventional inverter has to be increased. It will lead to higher switching losses and electromagnetic interference. The problem with lower switching frequency is the intro- duction of low order harmonics in phase currents and undesirable torque ripple in the motor. The 5th and 7th harmonics are dominant for hexagonal voltage space-vector based low frequency switching, and it is possible to eliminate these harmonics by dodecagonal switching. Further improvement in the waveform quality is possible by octadecagonal voltage space-vectors. In this case, the complete elimination of 11th and 13th harmonic is possible for the entire modulation range. The concepts of dodecagonal and octadecagonal voltage space-vectors are used in the proposed inverter topologies. The first topology proposed in this thesis consists of cascaded connection of two H-bridge cells. The two cells are fed from unequal DC voltage sources having a ratio of 1 : 0:366, and this inverter can produce six concentric dodecagonal voltage space- vectors. This ratio of voltages can be obtained easily from a combination of star-delta transformers, since 1 : 0:366 = ( p 3 + 1) : 1. The cascaded connection of two H-bridge cells can generate nine asymmetric pole voltage levels, and the combined three-phase inverter can produce 729 voltage space-vectors (9 9 9). From this large number of combinations, only certain voltage space-vectors are selected, which forms dodecagonal pattern. In the case of conventional multilevel inverters, the voltage space-vector diagram consists of equilateral triangles of equal size, but for the proposed inverter, the triangular regions are isosceles and are having different sizes. By properly placing the voltage space-vectors in a sampling period, it is possible to achieve lower switching frequency for the individual cells, with substantial improvement in the harmonic spectrum of the output voltage. During the experimental veri cation, the motor is operated at di erent speeds using open loop v=f control method. The samples taken are always synchronised with the start of the sector to get synchronised PWM. The number of samples per sector is decreased with increase in the fundamental frequency to limit the switching frequency. Even though many topologies are available in literature, the most preferred topology for drives application such as traction drives is the 3-level NPC structure. This implies that the industry is still looking for viable alternatives to construct multilevel inverter topologies based on available power circuits. The second work focuses on the development of a multilevel inverter for variable speed medium-voltage drive application with dodecagonal voltage space-vectors, using lesser number of switches and power sources compared to earlier implementations. It can generate three concentric 12-sided polygonal voltage space-vectors and it is based on commonly available 2-level and 3-level inverters. A simple PWM timing computation method based on the hexagonal space-vector PWM is developed. The sampled values of the three-phase reference voltages are initially converted to the timings of a two-level inverter. These timings are mapped to the dodecagonal timings using a change of basis transformation. The voltage space- vector diagram of the proposed drive consists of sixty isosceles triangular regions, and the dodecagonal timings calculated are converted to the timings of the inner triangles. A searching algorithm is used to identify the triangular region in which the reference vector is located. A front-end recti er that may be easily implemented using standard star-delta transformers is also developed, to provide near-unity power factor. To test the performance of the inverter drive, an open-loop v=f control is used on a three-phase induction motor under no-load condition. The harmonic spectra of the phase voltages were computed in order to analyse the harmonic distortion of the waveforms. The carrier frequency was kept around 1.2 KHz for the entire range of operation. If the switching frequency is decreased, the conventional hexagonal space-vector based switching introduce signifi cant 5th, 7th, 11th and 13th harmonics in the phase currents. Out of these dominant harmonics, the 5th and 7th harmonics can be completely suppressed using dodecagonal voltage space-vector based switching as observed in the first and second work. It is also possible to remove the 11th and the 13th harmonics by using voltage space-vectors with 18 sides. The last topology is based on multilevel octadecagonal (18-sided polygon) voltage space-vectors, and it has better harmonic performance than the previously mentioned topologies. Here, a multilevel inverter system capable of producing three octadecagonal voltage space-vectors is proposed for the fi rst time, along with a simple timing calculation method. The conventional three-level inverters are only required to construct the proposed drive. Four asymmetric power supply voltages with 0:3054Vdc, 0:3473Vdc, 0:2266Vdc and 0:1207Vdc are required for the operation of the drive, and it is the main drawback of the circuit. Generally front-end isolation transformer is essential for high-power drives and these asymmetric voltages can be easily obtained from the multiple windings of the isolation transformer. The total harmonic distortion of the phase current is improved due to the 18-sided voltage space-vector switching. The ratio of the radius of the largest polygon and its inscribing circle is cos10 = 0:985. This ratio in the case of hexagonal voltage space-vector modulation is cos30 = 0:866, which means that the range of the linear modulation for the proposed scheme is signifi cantly higher. The drive is designed for open-end winding induction motors and it has better fault tolerance. It any of the inverter fails, it can be easily bypassed and the drive will be still functional with reduced speed. Open loop v=f control and rotor flux oriented vector control schemes were used during the experimental verifi cation. TMS320F2812 DSP platform was used to execute the control code for the proposed drive schemes. For the entire range of operation, the carrier was synchronized with the fundamental. For the synchronization, the sampling period is varied dynamically so that the number of samples in a triangular region is fi xed, keeping the switching frequency around 1.2 KHz. The average execution time for the v=f code was found to be 20 S, where as for vector control it took nearly 100 S. The PWM terminals and I/O lines of the DSP is used to output the timings and the triangle number respectively. To convert the triangle number and the timings to IGBT gate drive logic, an FPGA (XC3S200) was used. A constant dead-time of 1.5 S is also implemented inside the FPGA. Opto-isolated gate drivers with desaturation protection (M57962L) were used to drive the IGBTs. Hall-effect sensors were used to measure the phase currents and DC bus voltages. An incremental shaft position encoder with 2500 pulse per revolution is also connected to the motor shaft, to measure the angular velocity. 1200 V, 75 A IGBT half-bridge module is used to realize the switches. The concepts were initially simulated and experimentally verifi ed using laboratory prototypes at low power. While these concepts maybe easily extended to higher power levels by using suitably rated devices, the control techniques presented shall still remain applicable.

For medium and high-voltage drive applications, multilevel inverters are very popular. It is due to their superior performance compared to 2-level inverters such as reduced harmonic content in the output voltage and current, lower common mode voltage and dv=dt, and lesser voltage stress on power switches. The popular circuit topologies for multilevel inverters are neutral point clamped, cascaded H-bridge and flying capacitor based circuits. There exist different combinations of these basic topologies to realize multilevel inverters with modularity, better fault tolerance, and reliability. Due to these advantages, multilevel converters are getting good acceptance from the industry, and researchers all over the world are continuously trying to improve the performance of these converters. To meet such demands, three multilevel inverter topologies are proposed in this thesis. These topologies can be used for high-power induction motor drives, and the concepts presented are also applicable for synchronous motor drives, grid-connected inverters, etc. To get nearly sinusoidal phase current waveforms, the switching frequency of the conventional inverter has to be increased. It will lead to higher switching losses and electromagnetic interference. The problem with lower switching frequency is the intro- duction of low order harmonics in phase currents and undesirable torque ripple in the motor. The 5th and 7th harmonics are dominant for hexagonal voltage space-vector based low frequency switching, and it is possible to eliminate these harmonics by dodecagonal switching. Further improvement in the waveform quality is possible by octadecagonal voltage space-vectors. In this case, the complete elimination of 11th and 13th harmonic is possible for the entire modulation range. The concepts of dodecagonal and octadecagonal voltage space-vectors are used in the proposed inverter topologies. The first topology proposed in this thesis consists of cascaded connection of two H-bridge cells. The two cells are fed from unequal DC voltage sources having a ratio of 1 : 0:366, and this inverter can produce six concentric dodecagonal voltage space- vectors. This ratio of voltages can be obtained easily from a combination of star-delta transformers, since 1 : 0:366 = ( p 3 + 1) : 1. The cascaded connection of two H-bridge cells can generate nine asymmetric pole voltage levels, and the combined three-phase inverter can produce 729 voltage space-vectors (9 9 9). From this large number of combinations, only certain voltage space-vectors are selected, which forms dodecagonal pattern. In the case of conventional multilevel inverters, the voltage space-vector diagram consists of equilateral triangles of equal size, but for the proposed inverter, the triangular regions are isosceles and are having different sizes. By properly placing the voltage space-vectors in a sampling period, it is possible to achieve lower switching frequency for the individual cells, with substantial improvement in the harmonic spectrum of the output voltage. During the experimental veri cation, the motor is operated at di erent speeds using open loop v=f control method. The samples taken are always synchronised with the start of the sector to get synchronised PWM. The number of samples per sector is decreased with increase in the fundamental frequency to limit the switching frequency. Even though many topologies are available in literature, the most preferred topology for drives application such as traction drives is the 3-level NPC structure. This implies that the industry is still looking for viable alternatives to construct multilevel inverter topologies based on available power circuits. The second work focuses on the development of a multilevel inverter for variable speed medium-voltage drive application with dodecagonal voltage space-vectors, using lesser number of switches and power sources compared to earlier implementations. It can generate three concentric 12-sided polygonal voltage space-vectors and it is based on commonly available 2-level and 3-level inverters. A simple PWM timing computation method based on the hexagonal space-vector PWM is developed. The sampled values of the three-phase reference voltages are initially converted to the timings of a two-level inverter. These timings are mapped to the dodecagonal timings using a change of basis transformation. The voltage space- vector diagram of the proposed drive consists of sixty isosceles triangular regions, and the dodecagonal timings calculated are converted to the timings of the inner triangles. A searching algorithm is used to identify the triangular region in which the reference vector is located. A front-end recti er that may be easily implemented using standard star-delta transformers is also developed, to provide near-unity power factor. To test the performance of the inverter drive, an open-loop v=f control is used on a three-phase induction motor under no-load condition. The harmonic spectra of the phase voltages were computed in order to analyse the harmonic distortion of the waveforms. The carrier frequency was kept around 1.2 KHz for the entire range of operation. If the switching frequency is decreased, the conventional hexagonal space-vector based switching introduce signifi cant 5th, 7th, 11th and 13th harmonics in the phase currents. Out of these dominant harmonics, the 5th and 7th harmonics can be completely suppressed using dodecagonal voltage space-vector based switching as observed in the first and second work. It is also possible to remove the 11th and the 13th harmonics by using voltage space-vectors with 18 sides. The last topology is based on multilevel octadecagonal (18-sided polygon) voltage space-vectors, and it has better harmonic performance than the previously mentioned topologies. Here, a multilevel inverter system capable of producing three octadecagonal voltage space-vectors is proposed for the fi rst time, along with a simple timing calculation method. The conventional three-level inverters are only required to construct the proposed drive. Four asymmetric power supply voltages with 0:3054Vdc, 0:3473Vdc, 0:2266Vdc and 0:1207Vdc are required for the operation of the drive, and it is the main drawback of the circuit. Generally front-end isolation transformer is essential for high-power drives and these asymmetric voltages can be easily obtained from the multiple windings of the isolation transformer. The total harmonic distortion of the phase current is improved due to the 18-sided voltage space-vector switching. The ratio of the radius of the largest polygon and its inscribing circle is cos10 = 0:985. This ratio in the case of hexagonal voltage space-vector modulation is cos30 = 0:866, which means that the range of the linear modulation for the proposed scheme is signifi cantly higher. The drive is designed for open-end winding induction motors and it has better fault tolerance. It any of the inverter fails, it can be easily bypassed and the drive will be still functional with reduced speed. Open loop v=f control and rotor flux oriented vector control schemes were used during the experimental verifi cation. TMS320F2812 DSP platform was used to execute the control code for the proposed drive schemes. For the entire range of operation, the carrier was synchronized with the fundamental. For the synchronization, the sampling period is varied dynamically so that the number of samples in a triangular region is fi xed, keeping the switching frequency around 1.2 KHz. The average execution time for the v=f code was found to be 20 S, where as for vector control it took nearly 100 S. The PWM terminals and I/O lines of the DSP is used to output the timings and the triangle number respectively. To convert the triangle number and the timings to IGBT gate drive logic, an FPGA (XC3S200) was used. A constant dead-time of 1.5 S is also implemented inside the FPGA. Opto-isolated gate drivers with desaturation protection (M57962L) were used to drive the IGBTs. Hall-effect sensors were used to measure the phase currents and DC bus voltages. An incremental shaft position encoder with 2500 pulse per revolution is also connected to the motor shaft, to measure the angular velocity. 1200 V, 75 A IGBT half-bridge module is used to realize the switches. The concepts were initially simulated and experimentally verifi ed using laboratory prototypes at low power. While these concepts maybe easily extended to higher power levels by using suitably rated devices, the control techniques presented shall still remain applicable.

Experimental research on high-power converters, particularly in an academic environment, faces severe infrastructural constraints. Usually, power source and loads of required ratings are not available. Further, more importantly, the energy consumption is huge. One possibility is to establish an experimental research platform, comprising of a network of high-power converters, through which power is circulated and which draws only the losses from the mains. This work deals with the establishment of a circulating power test set-up, comprising of two line-side PWM converters, inclusive of control and modulation methods for the two converters. Two types of circulating power test setups are developed. In the first setup, the converters are connected in parallel, on ac as well as dc sides, such that real and/or reactive power is circulated between them. In the second test setup, the dc buses of the converters are separated; hence, only reactive power circulation is possible. These setups are used to conduct heat-run tests with low energy expenditure on the PWM converters at various operating conditions up to power levels of 150 kVA. Further, these are used to validate analytically-evaluated thermal characteristics of high-power PWM converters. A safe thermal limit is derived for such converters in terms of apparent power (kVA) handled, power factor and switching frequency. The effects of voltage sag and of unequal current sharing between parallel IGBT modules on the safe thermal limit are studied. While the power drawn by the circulating-power setup from the grid is much lower than the ratings of the individual converters, the harmonic injection into the mains by the setup could be significant since the harmonics drawn by both converters tend to add up. This thesis investigates carrier interleaving to improve the waveform quality of grid current, drawn by the circulating-power test setup. The study of carrier interleaving is quite general and covers various applications of parallel-connected converters such as unity power factor rectification, static reactive power compensation and grid-connected renewable energy systems. In literature, carrier interleaving has been employed mainly for unity power factor rectifiers, sharing a common dc load equally. In such case, the fundamental components of the terminal voltages of the parallel converters are equal. However, when the power sharing between the two converters is unequal, or when power is circulated between the two converters, the terminal voltages of the two converters are not equal. A method to estimate rms grid current ripple, drawn by parallel-connected converters with equal and/or unequal terminal voltages, in a synchronous reference frame is presented. Further, the influence of carrier interleaving on the rms grid current ripple is studied. The optimum interleaving angle, which minimizes the rms grid current ripple under various applications, is investigated. This angle is found to be a function of modulation index of the converters in the equal terminal voltages case. In the unequal terminal voltages case, the optimum interleaving angle is shown to be a function of the average modulation index of the two parallel converters. The effect of carrier interleaving is experimentally studied on the reactive power circulation setup at different values of kVA and different dc bus voltages. The grid current ripple is measured for different values of interleaving angle. It is found experimentally that the optimum interleaving angle reduces the rms grid current ripple by between 37% and 48%, as compared without interleaving, at various operating conditions. Further, the reactive power circulation test set-up is used to evaluate and compare power conversion losses corresponding to different PWM techniques such as conventional space-vector PWM (CSVPWM), bus-clamping PWM (BCPWM) and advanced bus-clamping PWM methods for static reactive power compensator (STATCOM) application at high power levels. It is demonstrated theoretically as well as experimentally that an advanced bus-clamping PWM method, termed minimum switching loss PWM (MSLPWM), leads to significantly lower power conversion loss than CSVPWM and BCPWM techniques at a given average switching frequency.

Durant ces dernières années, l'intérêt pour les technologies des véhicules à faibles émissions de carbone a fait un bond important à travers l'Union européenne (UE) et au-delà, encouragé en cela par les gouvernements et les constructeurs automobiles. De grands espoirs ont été mis plus récemment dans les véhicules électriques (VE) et les véhicules électriques hybrides (VEH) en tant que technologies clés pour atténuer le changement climatique, améliorer la sécurité énergétique et favoriser une nouvelle branche de l'industrie dans le secteur automobile. Ainsi, l'électrification des transports a été considérée comme une stratégie clé pour réduire les émissions de CO2 dans le secteur des transports. Le principal défi est d’augmenter l’autonomie des véhicules (ce qui a toujours été au coeur de la concurrence des industries du transport), ainsi que la durée de vie des volumineuses et coûteuses batteries. Par conséquent, ceci indique que le rendement du convertisseur de puissance est un des points clés à développer pour les générations des véhicules électriques à venir. L’autre paramètre influant est la qualité de la tension et du courant (en particulier la suppression des harmoniques basses fréquences) qui permet de réduire la taille des filtres d'entrée et de sortie de ces convertisseurs. L'objectif de cette thèse est de parvenir à un meilleur rendement en proposant de nouvelles structures de convertisseur de puissance et des commandes vectorielles modifiées ; le choix de deux onduleurs alimentant un moteur ouvert aux deux extrémités. Après l'analyse étape par étape, modèle théorique, simulation et enfin une mise en oeuvre expérimentale, il a été constaté que les nouvelles méthodes proposées sont compétitives et peuvent s’appliquer aux cas des VEH et des VE afin d’apporter des caractéristiques supérieures en termes d’efficacité et de qualité de tension et de courant. / Over the last decade, the interest for low-carbon vehicle technologies has surged among both governments and automotive manufacturers across and beyond the European Union (EU). Great hopes have been put, first, on biofuel vehicles and more recently on electric vehicles (EVs) and hybrid electric vehicles (HEVs) as key technologies to mitigate climate change, enhance energy security and nurture new industry branches within the automotive sector. So electrification of vehicles has been seen as a key strategy to reduce CO2 emissions from the transport sector. The main challenge toward EVs and HEVs is to keep driving for longer distance (which has been always fields for competition among traction industries) as well as lifetime battery cells as storage system. As a result, these indicate importance of power converter efficiency as a key gate for next generations of these up-coming vehicles. The next parameter is the quality of output voltage/current (especially by suppressing low-order harmonics) to reduce the size of filtering. The aim of this thesis is to achieve better efficiency and output voltage/current Total Harmonic Distortion (THD) by proposing novel power converter and associated Pulse Width Modulation (PWM) methods while imposing modification on power converter topology. As a result, dual-inverter is proposed to supply open-end motor from both sides. To this aim, three PWM methods are suggested as: The first one, Modified Space Vector Modulation (MSVM) for dual-inverter supplied by single dc source, improves efficiency by 4-5% (while having lower switching losses), and reduces Common Mode Voltage (CMV) levels by 66%, as well. The voltage/current harmonics are analytically analyzed which shows mainly better performance. Effective switching frequency is also reduced by 66% due to the reduction of number of commutations. In the second one, Near State PWM (NSPWM) is adapted for dual-inverter supplied by single dc source in order to eliminate triplen harmonics (therefore Zero Sequence Voltage, ZSV) and improve efficiency (by 3-4%) compared to Space Vector Modulation (SVM). Additionally due to avoiding use of zero vectors, CMV is improved by 66%. While having 8 commutations instead of 12 in SVM, effective switching frequency is improved by 33%. And finally, the third proposed method deals with NSPWM for dual-inverter supplied by two isolated dc sources wherein efficiency and CMV levels show the same performance as previous one. However, in this method, voltage THD is highly reduced compared to SVM. Triplen harmonics of the output voltage are inherently suppressed by the structure. These 3 proposed methods are analytically studied and their performances are step by step simulated in Matlab/Simulink environment. Then the methods are implemented in dualinverter fed open-end motor in laboratory setup; and the results are compared with these of SVM. Finally, it is found that novel proposed methods are so competitive solutions to be applied in HEVs and EVs and bring superior efficiency and voltage/current harmonic features.