During the last decade, the Internet usage has been growing at an enormous rate which has beenaccompanied by the developments of network applications (e.g., video conference, audio/videostreaming, E-learning, E-Commerce and real-time applications) and allows several types ofinformation including data, voice, picture and media streaming. While end-users are demandingvery high quality of service (QoS) from their service providers, network undergoes a complex trafficwhich leads the transmission bottlenecks. Considerable effort has been made to study thecharacteristics and the behavior of the Internet. Simulation modeling of computer networkcongestion is a profitable and effective technique which fulfills the requirements to evaluate theperformance and QoS of networks. To simulate a single congested link, simulation is run with asingle load generator while for a larger simulation with complex traffic, where the nodes are spreadacross different geographical locations generating distributed artificial loads is indispensable. Onesolution is to elaborate a load generation system based on master/slave architecture.

Kraven på dagens trådlösa förbindelser kommer hela tiden att öka och med detta följer även högre krav på nya produkter som kan tillgodose de ökade kraven. För att göra processen från idé till produkt snabbare krävs enkla verktyg för att snabbt kunna gå från den formulerade standarden till en hårdvaruprototyp. Detta arbete har använt sig av ett av dessa verktyg som idag finns tillgängliga, Xilinx System Generator for DSP 1.1, för att ta fram sändare och mottagare för en del av den trådlösa standarden IEEE 802.11a. Arbetet ger en beskrivning av hur sändare och mottagare är uppbyggda samt även synpunkter på System Generator och beskrivningar av problem som uppstod under arbetet. / The demands on todays wireless communications will continue to increase and with this follows a demand for shorter and shorter development times for the products that are going to satisfy this demand. To accomplish this shorter development time simple tools for going from the formulated standard to a hardware prototype is needed. This work uses one of these tools today available, Xilinx System Generator for DSP 1.1, to develop a transmitter and a reciever for a part of the wireless standard IEEE 802.11a. The work gives a description of the building blocks of the transmitter and the reciever but also some views on System Generator and descriptions of problems that were encountered during the work.

Multiplication is an important part of real-time system applications. Various hardware parallel multipliers used in such applications have been proposed. However, when the operand sizes of the multipliers and the process technology need to be changed, the existing multipliers have to be redesigned. From the point of library cell reuse, this master thesis work aims at developing a module generator for parallel multipliers with the help of software programs. This generator can be used to create the gate-level schematic for fixed point two's complement number multipliers. Based on the generated schematic, the entire multiplier can be implemented by small manual intervention. This feature can reduce the time of chip design. The design phases consist of the logic, circuit and physical designs. The logic design includes gate-level schematic generation with C and SKILL programs and structural VHDL-code descriptions as well as validation. The circuit and physical design are custom in Cadence and the routing uses automatic place and route tools. To demonstrate the design method, an 18 by 18-bit modified Booth recoded multiplier was implemented in 0.18 µm CMOS process with a supply voltage of 1.2 V and simulated using simulator (Spectre). The number of integrated transistors is 13000 and the active area is 85000 µm2. The postlayout simulation shows the critical path with a delay of 17 ns.

Communication and digital signal processing applications of today are often developed as fully integrated systems on one single chip and are implemented as application specific integrated circuits using e.g. VLSI technology. As the systems are getting more and more complex in terms of speed and performance the chip size and the design time tend to increase rapidly. This will result in search for cheaper and less time consuming alternatives. One alternative is field programmable gate arrays, so called FPGAs. The FPGAs are getting faster, cheaper and the number of gates increases all the time. A long list of ready to use functional blocks so called intellectual property (IP) blocks can be used in FPGAs. The latest FPGAs can also be bought with one or more embedded processors, in form of hard processor cores or as licenses for soft processor cores. This will speed up the design phase and of course also decrease the crucial time to market even more. The purpose of this master’s thesis was to develop a waveform generator to generate a sine signal and a cosine signal, I and Q, used for radio/radar applications. The digital signals should have an output data rate of at least 100 MHz. The digital part of the system should be implemented in hardware using e.g. an FPGA. To convert the digital signals to analog signals two D/A converters are used. The analog signals, I and Q, should have a bandwidth of 1 MHz - 11 MHz. The waveform generator was developed and implemented using a Virtex II FPGA from Xilinx. An embedded microprocessor within the FPGA, MicroBlaze, in form of a soft processor core was used to control the system. A user interface program running on the microprocessor was also developed. Testing of the whole system, both hardware and software, was done. The system is able to generate digital sine and cosine curves of an output data rate of 100 MHz.

The development in electronics increases the demand for good design methods and design tools in the field of electrical engeneering. To improve their design methods Ericsson Microwave Systems AB is interested in using computer tools to create a link between the specification and the implementation of a digital system in a FPGA. Xilinx System Generator for DSP is a tool for implementing a model of a digital signalprocessing algorithm in a Xilinx FPGA. To evaluate Xilinx System Generator two testcases has been designed. The testcases are selected to represent the FPGA designs made at Ericsson Microwave Systems. The testcases show that Xilinx System Generator can be used to effectivly implement a model made in Simulink in a FPGA from Xilinx. The result of the implementation is comparable to the implementation of VHDL code written by hand. The use of tools for implementation of a model in hardware cause change in the design methods used at Ericsson Microwave Systems. The higher level of abstraction introduced by System Generator results in the design decisions made at system level having a higher impact on the final realization.

In different applications, in digital domain, it is necessary to change the sampling rate by an arbitrary number. For example Software Radio which should handle different conversion factors and standards. This work focuses on the problem of designing and implement sampling rate converters for conversions between arbitrary sampling rates. The report presents an overview of different converter techniques as well as considers a suitable scheme with low implementation cost. The creating VHDL generator of Farrow-based structure to speed up the design process is the main task of this work. The suitable design technique which is the most important thing in any design work is presented in the report as well. The scheme which is considered to be suitable is created by VHDL generator and tested in MATLAB. The source code is attached to the report. And some results from tests of the implemented scheme.

In this work, an existing generator for layout of Static Random Access Memory (SRAM) is improved. The tool is completed with a block decoder, which was missing when the thesis started. A feature of generating schematic files is also added. The schematics are important to get a better overview, to test parts properly, and enable Layout versus Schematics (LVS) checks. The main focus of this thesis work is to implement and evaluate a new SRAM cell, called Zero Aware Asymmetric SRAM cell. This cell saves major power when zeros are stored. Furthermore the pull-up circuit is modified to be less power consuming. Other parts are also modified to fit the new memory cell. Several minor flaws are corrected in the layout generator. It does still not produce a complete memory without manual interventions, but it does at least create all parts with one command. Several tests, including Design Rule Checks (DRC) and LVS checks, are carried out both on minor and larger parts. Development of documentation that makes it easier for users and developers to use and understand the tool is initiated.

This thesis discusses the design and implementation of a VHDL generator for Wallace tree with (3:2) counter modules and (2:2) counter modules to solve fast addition problem. The basic research has been carried out by MATLAB programming environment and automatic generation of VHDL file based on the result obtained from MATLAB simulation. MODELSIM has been used for compilation and simulation of the VHDL file.

In this work, an existing RAM generator is analysed and evaluated. Some of the aspects that were considered in the evaluation are the optimization of the basic SRAM cell, how the RAM generator can be ported to newer technologys, automating the simulation process and the creation of the workflow for the energy model. One of the main focus of this thesis work is to optimize the basic SRAM cell. The SRAM cell which is used in the RAM generator is not optimized for area nor power. A compact layout is suggested which saves a lot of area and power. The technology that is used to create the RAM generator is old and a suitable way to port it to newer technology has also been found. To create an energy model one has to simulate a lot of memories with a lot of data. This cannot be done in the traditional way of simulating circuits using the GUI. Hence an automation procedure has been suggested which can be made to work to create energy models by simulating the memories comprehensively. Finally, basic ground work has been initiated by creating a workflow for the creation of the energy model.

This short note discusses performance bounds for "Ahrens" algorithm, that can generate random variates from continuous distributions with monotonically decreasing density. This rejection algorithms uses constant hat-functions and constant squeezes over many small intervals. The choice of these intervals is important. Ahrens has demonstrated that the equal area rule that uses strips of constant area leads to a very simple algorithm. We present bounds on the rejection constant of this algorithm depending only on the number of intervals. (author's abstract) / Series: Preprint Series / Department of Applied Statistics and Data Processing