Au cours du traitement thermique rapide (RTP) des cellules photovoltaïques à couches minces, un suivi du profil de température souhaité et une homogénéité de la chauffe substrat doivent être assurés. Le but de cette thèse est de proposer une méthodologie de conception d'un four RTP permettant d'atteindre la qualité du cycle de la chauffe souhaitée.Une modélisation thermique est réalisée en se basant sur la méthode de réseaux de composants afin de prédire le comportement thermique dynamique du four. L'approximation des flux plans et l'approximation des couches minces semi-transparentes sont utilisées pour le calcul des facteurs d'échanges directs. L'algorithme des revêtements est appliqué pour en déduire les facteurs de transfert. Le modèle thermique développé est validé expérimentalement sur un four de petites dimensions. Une méthodologie de conception du four RTP est proposée en tenant compte de l'aspect dynamique des conditions thermiques du four. Une optimisation par algorithme génétique est effectuée pour trouver l'emplacement des émetteurs. Pour chacune des configurations testées, la distribution de la puissance aux émetteurs à fournir à chaque instant est optimisée par programmation dynamique. Finalement, cette méthodologie est appliquée pour la conception d'un four RTP pour le traitement de cellules photovoltaïques à couches minces de 30 × 60 cm2. Les résultats des essais confirment la validité de la méthodologie proposée. / During the rapid thermal processing (RTP) of thin film photovoltaic cells, the temperature of the latter has to follow a preset time evolution profile, while keeping spatial uniformity of the wafer. The aim of this study is to propose a design methodology of RTP furnace in order to obtain the quality of the required heating cycle.A thermal modeling is performed based on the component interaction network approach to predict the thermal behavior of the furnace. Flux plane approximation and semi-transparent thin layer approximation are used to calculate the direct exchange factor. The plating algorithm is then applied to calculate the transfer factor. The thermal model developed is validated experimentally on a furnace of small dimensions. A methodology to design a RTP furnace is proposed taking into account the dynamic aspect of the thermal conditions of the furnace. An optimization using the genetic algorithm is performed in order to find emitter dispositions. For each tested configuration, the optimal input power distribution over the emitters at each time step is found by using real time dynamic programming. Finally, the methodology is applied for the design of RTP furnace for the heat treatment of thin film photovoltaic cells of 30 × 60 cm2. Test results confirm the validity of the methodology proposed.

We report on a novel silicon nanowire-based field effect transistor with integrated ferroelectric gate oxide. The concept allows tuning the carrier transport in a non-volatile approach by switching the polarization in the ferroelectric layer close to the source Schottky-junction. We interpret the results in terms of tuning the transmissibility of the Schottky-junction for charge carriers. The experimental results provide a first step towards the integration of memory-in-logic concepts with reconfigurable nanowire transistors.

Integration of high-K Metal-Insulator-Metal (MIM) capacitors in the Back-end-of-line (BEOL) is a topic of interest for the further development of the process at KTH Royal Institute of Technology. MIM-capacitors benefit from having constant capacitance values over a range of voltages and/or frequencies. One significant limitation in the development of better MIM-capacitors is the temperature consideration for BEOL processes. For the process at KTH Institute of Technology the temperature should not exceed 600 °C, as this would damage underlying devices. This work aims to fabricate aluminium oxide MIM-capacitors as a standard BEOL process performed at low temperature, which has been achieved via atomic layer deposition (ALD). The fabricated aluminium oxide MIM-capacitors had a good quality factor, series resistance and low dissipation. The capacitance for a 10 nm thick aluminium oxide insulator layer was 1 µF/cm2, which exceeds the set requirement. This work also aimed to make ferroelectric aluminium doped hafnium oxide MIM-capacitors using ALD. The doping ratio was varied in ALD as this had been found to affect formation of the ferroelectric crystal phase after a rapid thermal annealing step. Three wafers of 20 nm thick hafnium oxide and differing ratios were found to not be ferroelectric. The intermediate doping ratio was found to appear slightly anti-ferroelectric. A 10 nm thick doped hafnium oxide of intermediate doping was also fabricated and was found to be ferroelectric with a remnant polarisation of 1 µC/cm2. Though this polarisation is relatively small, it shows that top electrode induced strain due to lattice mismatch could be responsible for the ferroelectric properties of the capacitor. The quality of the hafnium based capacitors seemed worse in comparison to the aluminium oxide capacitors, which is suspected to be due to oxygen vacancies, resulting in a high loss tangent. While this first experiment showed promising results, the ferroelectric remnant polarisation should be increased by an order of magnitude and the electrical benchmark values should be improved before these hafnium oxide MIM-capacitors can be used in the BEOL process. / Integratie van high-K MIM-condensatoren in de Back-end-of-line (BEOL) is een onderwerp van belang voor de ontwikkeling van het proces bij de KTH. MIM-condensatoren profiteren van een constante capaciteitswaarde over een reeks spanningen en/of frequenties. Een belangrijke beperking bij de ontwikkeling van betere MIM-condensatoren is het temperatuur limiet voor BEOL-processen. Bij de KTH moet de temperatuur niet hoger zijn dan 600 °C, omdat dit de onderliggende apparaten zou beschadigen. Dit werk heeft tot doel aluminiumoxide MIM-condensatoren te fabriceren als een standaard BEOL-proces met lage temperatuur, en heeft dit inderdaad bereikt via atomaire laagafzetting (ALD). De gefabriceerde aluminiumoxide MIM-condensatoren hadden een goede kwaliteitsfactor, serieweerstand en lage dissipatie. De capaciteit voor een 10 nm dikke aluminiumoxide-isolatorlaag was 1µF/cm2, hoger dan de gestelde eisen. Dit werk was ook gericht op het maken van ferro-elektrische aluminium gedoteerde hafniumoxide MIM-condensatoren met behulp van ALD. De doteringsverhouding werd gevarieerd in ALD, aangezien bleek dat dit de vorming van de ferro-elektrische kristalfase faciliteerde na een snelle thermische gloeistap. Drie wafers van 20 nm dik hafniumoxide en verschillende verhoudingen bleken niet ferro-elektrisch te zijn. De tussenliggende doteringsverhouding bleek enigszins anti-ferro-elektrisch te zijn. Een 10 nm dik gedoteerd hafniumoxide met intermediaire dotering werd ook gefabriceerd en bleek ferro-elektrisch te zijn met een restpolarisatie van 1 µC/cm2. Hoewel deze polarisatie relatief klein is, toont het aan dat de door de topelektrode geïnduceerde spanning als gevolg van roostermismatch verantwoordelijk zou kunnen zijn voor de ferro-elektrische eigenschappen van de condensator. De kwaliteit van de op hafnium gebaseerde isolator leek slechter in vergelijking met die van aluminiumoxide, hetgeen kan worden toegeschreven aan gebrek van zuurstof in het rooster, wat in een groot verlies resulteert. De ferro-elektriciteit moet met een orde van grootte worden verhoogd en de elektrische benchmarks moeten ook verhoogd worden voordat deze hafniumoxide MIM-condensatoren kunnen worden gebruikt in het BEOLproces. Sleutelwoorden: atomaire laagafzetting (ALD), Ferro-elektrisch, Metaal-Isolator- Metaal (MIM) condensator, lage temperatuur, snelle thermische gloeiing.

Nickel und Nickel (II) -oxid werden in großem Umfang in fortgeschrittenen elektronischen Geräten verwendet. In der Mikroelektronik-Industrie wird Nickel verwendet werden, um Nickelsilizid bilden. Die Nickelmono Silizid (NiSi) wurde als ausgezeichnetes Material für Source-Drain-Kontaktanwendungen unter 45 nm-CMOS-Technologie entwickelt. Im Vergleich zu anderen Siliziden für die Kontaktanwendungen verwendet wird NiSi wegen seines niedrigen spezifischen Widerstand, niedrigen Kontaktwiderstand, relativ niedrigen Bildungstemperatur und niedrigem Siliziumverbrauchs bevorzugt. Nickel in Nickelbasis-Akkus und ferromagnetischen Direktzugriffsspeicher (RAMs) verwendet. Nickel (II) oxid wird als Transistor-Gate-Oxid und Oxid in resistive RAM genutzt wird. Atomic Layer Deposition (ALD) ist eine spezielle Art der Chemical Vapor Deposition (CVD), das verwendet wird, um sehr glatte sowie homogene Dünnfilme mit hervorragenden Treue auch bei hohen Seitenverhältnissen abzuscheiden. Es basiert auf selbstabschließenden sequentielle Gas-Feststoff-Reaktionen, die eine präzise Steuerung der Filmdicke auf wenige Angström lassen sich auf der Basis. Zur Herstellung der heutigen 3D-elektronische Geräte, sind Technologien wie ALD erforderlich. Trotz der Vielzahl von praktischen Anwendungen von Nickel und Nickel (II) -oxid, sind einige Nickelvorstufen zur thermischen basierend ALD erhältlich. Darüber hinaus haben diese Vorstufen bei schlechten Filmeigenschaften führte und die Prozesseigenschaften wurden ebenfalls begrenzt. Daher in dieser Masterarbeit mussten die Eigenschaften verschiedener neuartiger Nickelvorstufen zu bewerten. Alle neuen Vorstufen heteroleptische (verschiedene Arten von Liganden) und Komplexe wurden vom Hersteller speziell zur thermischen basierend ALD aus reinem Nickel mit H 2 als ein Co-Reaktionsmittel gestaltet. Um die neuartige Vorläufer zu untersuchen, wurde eine neue Methode entwickelt, um kleine Mengen in einer sehr zeitsparend (bis zu 2 g) von Ausgangsstoffen zu testen. Diese Methodologie beinhaltet: TGA / DTA-Kurve analysiert der Vorstufen, thermische Stabilitätstests in dem die Vorläufer (<0,1 g) wurden bei erhöhter Temperatur in einer abgedichteten Umgebung für mehrere Stunden wurde die Abscheidung Experimenten und Film Charakterisierungen erhitzt. Die Abscheidungen wurden mit Hilfe der in situ Quarzmikrowaage überwacht, während die anwendungsbezogenen Filmeigenschaften, wie chemische Zusammensetzung, physikalische Phase, Dicke, Dichte, Härte und Schichtwiderstand wurden mit Hilfe von ex situ Messverfahren untersucht. Vor der Evaluierung neuartiger Nickelvorstufen ein Benchmark ALD-Prozess war vom Referenznickelvorläufer (Ni (AMD)) und Luft als Reaktionspartner entwickelt. Das Hauptziel der Entwicklung und Optimierung von solchen Benchmark-ALD-Prozess war es, Standard-Prozessparameter wie zweite Reaktionspartner Belichtungszeiten, Argonspülung Zeiten, gesamtprozessdruck, beginnend Abscheidungstemperatur und Gasströme zu extrahieren. Diese Standard-Prozessparameter mussten verwendet, um die Prozessentwicklung Aufgabe (das spart Vorläufer Verbrauch) zu verkürzen und die Sublimationstemperatur Optimierung für jede neuartige Vorstufe werden. Die ALD Verhalten wurde in Bezug auf die Wachstumsrate durch Variation des Nickelvorläuferbelichtungszeit, Vorläufer Temperatur und Niederschlagstemperatur überprüft. / Nickel and nickel(II) oxide are widely used in advanced electronic devices . In microelectronic industry, nickel is used to form nickel silicide. The nickel mono-silicide (NiSi) has emerged as an excellent material of choice for source-drain contact applications below 45 nm node CMOS technology. As compared to other silicides used for the contact applications, NiSi is preferred because of its low resistivity, low contact resistance, relatively low formation temperature and low silicon consumption. Nickel is used in nickel-based rechargeable batteries and ferromagnetic random access memories (RAMs). Nickel(II) oxide is utilized as transistor gate-oxide and oxide in resistive RAMs. Atomic Layer Deposition (ALD) is a special type of Chemical Vapor Deposition (CVD) technique, that is used to deposit very smooth as well as homogeneous thin films with excellent conformality even at high aspect ratios. It is based on self-terminating sequential gas-solid reactions that allow a precise control of film thickness down to few Angstroms. In order to fabricate todays 3D electronic devices, technologies like ALD are required. In spite of huge number of practical applications of nickel and nickel(II) oxide, a few nickel precursors are available for thermal based ALD. Moreover, these precursors have resulted in poor film qualities and the process properties were also limited. Therefore in this master thesis, the properties of various novel nickel precursors had to be evaluated. All novel precursors are heteroleptic (different types of ligands) complexes and were specially designed by the manufacturer for thermal based ALD of pure nickel with H 2 as a co-reactant. In order to evaluate the novel precursors, a new methodology was designed to test small amounts (down to 2 g) of precursors in a very time efficient way. This methodology includes: TGA/DTA curve analyses of the precursors, thermal stability tests in which the precursors (< 0.1 g) were heated at elevated temperatures in a sealed environment for several hours, deposition experiments, and film characterizations. The depositions were monitored with the help of in situ quartz crystal microbalance, while application related film properties like chemical composition, physical phase, thickness, density, roughness and sheet resistance were investigated with the help of ex situ measurement techniques. Prior to the evaluation of novel nickel precursors, a benchmark ALD process was developed from the reference nickel precursor (Ni(amd)) and air as a co-reactant. The main goal of developing and optimizing such benchmark ALD process was to extract standard process parameters like second-reactant exposure times, Argon purge times, total process pressure, starting deposition temperature and gas flows. These standard process parameters had to be utilized to shorten the process development task (thus saving precursor consumption) and optimize the sublimation temperature for each novel precursor. The ALD behaviour was checked in terms of growth rate by varying the nickel precursor exposure time, precursor temperature and deposition temperature.

Nickel und Nickel (II) -oxid werden in großem Umfang in fortgeschrittenen elektronischen Geräten verwendet. In der Mikroelektronik-Industrie wird Nickel verwendet werden, um Nickelsilizid bilden. Die Nickelmono Silizid (NiSi) wurde als ausgezeichnetes Material für Source-Drain-Kontaktanwendungen unter 45 nm-CMOS-Technologie entwickelt. Im Vergleich zu anderen Siliziden für die Kontaktanwendungen verwendet wird NiSi wegen seines niedrigen spezifischen Widerstand, niedrigen Kontaktwiderstand, relativ niedrigen Bildungstemperatur und niedrigem Siliziumverbrauchs bevorzugt. Nickel in Nickelbasis-Akkus und ferromagnetischen Direktzugriffsspeicher (RAMs) verwendet. Nickel (II) oxid wird als Transistor-Gate-Oxid und Oxid in resistive RAM genutzt wird. Atomic Layer Deposition (ALD) ist eine spezielle Art der Chemical Vapor Deposition (CVD), das verwendet wird, um sehr glatte sowie homogene Dünnfilme mit hervorragenden Treue auch bei hohen Seitenverhältnissen abzuscheiden. Es basiert auf selbstabschließenden sequentielle Gas-Feststoff-Reaktionen, die eine präzise Steuerung der Filmdicke auf wenige Angström lassen sich auf der Basis. Zur Herstellung der heutigen 3D-elektronische Geräte, sind Technologien wie ALD erforderlich. Trotz der Vielzahl von praktischen Anwendungen von Nickel und Nickel (II) -oxid, sind einige Nickelvorstufen zur thermischen basierend ALD erhältlich. Darüber hinaus haben diese Vorstufen bei schlechten Filmeigenschaften führte und die Prozesseigenschaften wurden ebenfalls begrenzt. Daher in dieser Masterarbeit mussten die Eigenschaften verschiedener neuartiger Nickelvorstufen zu bewerten. Alle neuen Vorstufen heteroleptische (verschiedene Arten von Liganden) und Komplexe wurden vom Hersteller speziell zur thermischen basierend ALD aus reinem Nickel mit H 2 als ein Co-Reaktionsmittel gestaltet. Um die neuartige Vorläufer zu untersuchen, wurde eine neue Methode entwickelt, um kleine Mengen in einer sehr zeitsparend (bis zu 2 g) von Ausgangsstoffen zu testen. Diese Methodologie beinhaltet: TGA / DTA-Kurve analysiert der Vorstufen, thermische Stabilitätstests in dem die Vorläufer (<0,1 g) wurden bei erhöhter Temperatur in einer abgedichteten Umgebung für mehrere Stunden wurde die Abscheidung Experimenten und Film Charakterisierungen erhitzt. Die Abscheidungen wurden mit Hilfe der in situ Quarzmikrowaage überwacht, während die anwendungsbezogenen Filmeigenschaften, wie chemische Zusammensetzung, physikalische Phase, Dicke, Dichte, Härte und Schichtwiderstand wurden mit Hilfe von ex situ Messverfahren untersucht. Vor der Evaluierung neuartiger Nickelvorstufen ein Benchmark ALD-Prozess war vom Referenznickelvorläufer (Ni (AMD)) und Luft als Reaktionspartner entwickelt. Das Hauptziel der Entwicklung und Optimierung von solchen Benchmark-ALD-Prozess war es, Standard-Prozessparameter wie zweite Reaktionspartner Belichtungszeiten, Argonspülung Zeiten, gesamtprozessdruck, beginnend Abscheidungstemperatur und Gasströme zu extrahieren. Diese Standard-Prozessparameter mussten verwendet, um die Prozessentwicklung Aufgabe (das spart Vorläufer Verbrauch) zu verkürzen und die Sublimationstemperatur Optimierung für jede neuartige Vorstufe werden. Die ALD Verhalten wurde in Bezug auf die Wachstumsrate durch Variation des Nickelvorläuferbelichtungszeit, Vorläufer Temperatur und Niederschlagstemperatur überprüft.:Lists of Abbreviations and Symbols VIII Lists of Figures and Tables XIV 1 Introduction 1 I Theoretical Part 3 2 Nickel and Nickel Oxides 4 2.1 Introduction and Existence 5 2.2 Material properties of Nickel and Nickel Oxide 5 2.3 Application in electronic industry 5 3 Atomic Layer Deposition 7 3.1 History 8 3.2 Definition 8 3.3 Features of thermal-ALD 8 3.3.1 ALD growth mechanism – an ideal view 8 3.3.2 ALD growth behaviour 10 3.3.3 Growth mode 11 3.3.4 ALD temperature window 11 3.4 Benefits and limitations 12 3.5 Precursor properties for thermal-ALD 13 3.6 ALD & CVD of Nickel – A literature survey 13 4 Metrology 17 4.1 Thermal analysis of precursors 18 4.2 Film and growth characterization 21 4.2.1 Quartz Crystal Microbalance 21 4.2.2 Spectroscopic Ellipsometry 24 4.2.3 X-Ray Photoelectron Spectroscopy 28 4.2.4 Scanning Electron Microscopy 29 4.2.5 X-Ray Reflectometry and X-Ray Diffraction 29 4.2.6 Four Point Probe Technique 20 5 Rapid Thermal Processing 32 5.1 Introduction 33 5.2 Basics of RTP 33 5.3 Nickel Silicides-A literature survey 33 II Experimental Part 36 6 Methodologies 37 6.1 Experimental setup 38 6.2 ALD process 41 6.2.1 ALD process types and substrate setups 41 6.2.2 Process parameters 41 6.3 Experimental procedure 42 6.3.1 Tool preparation 42 6.3.2 Thermal analysis and ALD experiments from nickel precursors 43 6.3.3 Data acquisition and evaluation 44 6.3.4 Characterization of film properties 46 7 Results and discussion 48 7.1 Introduction 49 7.2 QCM verification with Aluminum Oxide ALD process 49 7.3 ALD process from the reference precursor 50 7.3.1 Introduction 50 7.3.2 TG analysis for Ni(amd) precursor 51 7.3.3 Thermal stability test for Ni(amd) 51 7.3.4 ALD process optimization 52 7.3.5 Film properties 54 7.4 Evaluating the novel Nickel precursors 55 7.4.1 Screening tests for precursor P1 55 7.4.2 Screening tests for precursor P2 62 7.4.3 Screening tests for precursor P3 66 7.4.4 Screening tests for precursor P4 70 7.4.5 Screening tests for precursor P5 72 7.5 Comparison of all nickel precursors used in this work 74 8 Conclusions and outlook 77 References 83 III Appendix 101 A Deposition temperature control & Ellipsometry model 102 B Gas flow plan 105 / Nickel and nickel(II) oxide are widely used in advanced electronic devices . In microelectronic industry, nickel is used to form nickel silicide. The nickel mono-silicide (NiSi) has emerged as an excellent material of choice for source-drain contact applications below 45 nm node CMOS technology. As compared to other silicides used for the contact applications, NiSi is preferred because of its low resistivity, low contact resistance, relatively low formation temperature and low silicon consumption. Nickel is used in nickel-based rechargeable batteries and ferromagnetic random access memories (RAMs). Nickel(II) oxide is utilized as transistor gate-oxide and oxide in resistive RAMs. Atomic Layer Deposition (ALD) is a special type of Chemical Vapor Deposition (CVD) technique, that is used to deposit very smooth as well as homogeneous thin films with excellent conformality even at high aspect ratios. It is based on self-terminating sequential gas-solid reactions that allow a precise control of film thickness down to few Angstroms. In order to fabricate todays 3D electronic devices, technologies like ALD are required. In spite of huge number of practical applications of nickel and nickel(II) oxide, a few nickel precursors are available for thermal based ALD. Moreover, these precursors have resulted in poor film qualities and the process properties were also limited. Therefore in this master thesis, the properties of various novel nickel precursors had to be evaluated. All novel precursors are heteroleptic (different types of ligands) complexes and were specially designed by the manufacturer for thermal based ALD of pure nickel with H 2 as a co-reactant. In order to evaluate the novel precursors, a new methodology was designed to test small amounts (down to 2 g) of precursors in a very time efficient way. This methodology includes: TGA/DTA curve analyses of the precursors, thermal stability tests in which the precursors (< 0.1 g) were heated at elevated temperatures in a sealed environment for several hours, deposition experiments, and film characterizations. The depositions were monitored with the help of in situ quartz crystal microbalance, while application related film properties like chemical composition, physical phase, thickness, density, roughness and sheet resistance were investigated with the help of ex situ measurement techniques. Prior to the evaluation of novel nickel precursors, a benchmark ALD process was developed from the reference nickel precursor (Ni(amd)) and air as a co-reactant. The main goal of developing and optimizing such benchmark ALD process was to extract standard process parameters like second-reactant exposure times, Argon purge times, total process pressure, starting deposition temperature and gas flows. These standard process parameters had to be utilized to shorten the process development task (thus saving precursor consumption) and optimize the sublimation temperature for each novel precursor. The ALD behaviour was checked in terms of growth rate by varying the nickel precursor exposure time, precursor temperature and deposition temperature.:Lists of Abbreviations and Symbols VIII Lists of Figures and Tables XIV 1 Introduction 1 I Theoretical Part 3 2 Nickel and Nickel Oxides 4 2.1 Introduction and Existence 5 2.2 Material properties of Nickel and Nickel Oxide 5 2.3 Application in electronic industry 5 3 Atomic Layer Deposition 7 3.1 History 8 3.2 Definition 8 3.3 Features of thermal-ALD 8 3.3.1 ALD growth mechanism – an ideal view 8 3.3.2 ALD growth behaviour 10 3.3.3 Growth mode 11 3.3.4 ALD temperature window 11 3.4 Benefits and limitations 12 3.5 Precursor properties for thermal-ALD 13 3.6 ALD & CVD of Nickel – A literature survey 13 4 Metrology 17 4.1 Thermal analysis of precursors 18 4.2 Film and growth characterization 21 4.2.1 Quartz Crystal Microbalance 21 4.2.2 Spectroscopic Ellipsometry 24 4.2.3 X-Ray Photoelectron Spectroscopy 28 4.2.4 Scanning Electron Microscopy 29 4.2.5 X-Ray Reflectometry and X-Ray Diffraction 29 4.2.6 Four Point Probe Technique 20 5 Rapid Thermal Processing 32 5.1 Introduction 33 5.2 Basics of RTP 33 5.3 Nickel Silicides-A literature survey 33 II Experimental Part 36 6 Methodologies 37 6.1 Experimental setup 38 6.2 ALD process 41 6.2.1 ALD process types and substrate setups 41 6.2.2 Process parameters 41 6.3 Experimental procedure 42 6.3.1 Tool preparation 42 6.3.2 Thermal analysis and ALD experiments from nickel precursors 43 6.3.3 Data acquisition and evaluation 44 6.3.4 Characterization of film properties 46 7 Results and discussion 48 7.1 Introduction 49 7.2 QCM verification with Aluminum Oxide ALD process 49 7.3 ALD process from the reference precursor 50 7.3.1 Introduction 50 7.3.2 TG analysis for Ni(amd) precursor 51 7.3.3 Thermal stability test for Ni(amd) 51 7.3.4 ALD process optimization 52 7.3.5 Film properties 54 7.4 Evaluating the novel Nickel precursors 55 7.4.1 Screening tests for precursor P1 55 7.4.2 Screening tests for precursor P2 62 7.4.3 Screening tests for precursor P3 66 7.4.4 Screening tests for precursor P4 70 7.4.5 Screening tests for precursor P5 72 7.5 Comparison of all nickel precursors used in this work 74 8 Conclusions and outlook 77 References 83 III Appendix 101 A Deposition temperature control & Ellipsometry model 102 B Gas flow plan 105

Chemically ordered FePt is one of the most promising materials to reach the ultimate limitations in storage density of future magnetic recording devices due to its high uniaxial magnetocrystalline anisotropy and a corrosion resistance superior to rare-earth based magnets. In this study, FePt and FePt/Cu bilayers have been sputter deposited at room temperature onto thermally oxidized silicon wafers, glass substrates and self-assembled arrays of spherical SiO2 particles with diameters down to 10 nm. Millisecond flash lamp annealing, as well as conventional rapid thermal annealing was employed to induce the phase transformation from the chemically disordered A1 phase into the chemically ordered L10 phase. The influence of the annealing temperature, annealing time and the film thickness on the ordering transformation and (001) texture evolution of FePt films with near equiatomic composition was studied. Whereas flash lamp annealed FePt films exhibit a polycrystalline morphology with high chemical L10 order, rapid thermal annealing can lead to the formation of chemically ordered FePt fifilms with (001) texture on amorphous SiO2/Si substrates. The resultant high perpendicular magnetic anisotropy and large coercivities up to 40 kOe are demonstrated. Simultaneuosly to the ordering transformation, rapid thermal annealing to temperatures exceeding 600 °C leads to a break up of the continuous FePt film into separated islands. This dewetting behavior was utilized to create regular arrays of FePt nanostructures on SiO2 particle templates with periods down to 50 nm. The addition of Cu improves the (001) texture formation and chemcial ordering for annealing temperatures T < 600 °C. In addition, the magnetic anisotropy and the coercivity of the ternary FePtCu alloy can be effectively tailored by adjusting the Cu content. The prospects of FePtCu based exchange spring media, as well as the magnetic properties of FePtCu nanostructures fabricated using e-beam and nanoimprint lithography have been investigated.

Ce mémoire présente les efforts effectués pour réduire l'angle de perte de couches de pentoxyde de tantale amorphes telles qu'utilisées pour les miroirs de LIGO. Afin d'améliorer le niveau de relaxation des couches, celles-ci ont été déposées par pulvérisation cathodique magnétron à des températures allant de 50 °C à 480 °C, elles ont subi un recuit thermique rapide, elles ont été implantées par des ions d'oxygène, elles ont été déposées par pulvérisation cathodique magnétron en appliquant une tension de polarisation sur le substrat lors du dépôt allant de 0 V à -450 V et elles ont été déposées par pulvérisation cathodique magnétron pulsée à haute puissance dans le cadre de différentes expériences. L'angle de perte, l'épaisseur, la rugosité, l'indice de réfraction, la composition atomique, la contrainte, l'état de relaxation et le module de Young des couches ont par la suite été trouvés à l'aide de l'ellipsométrie spectralement résolue, la spectrométrie de rétrodiffusion de Rutherford, la détection des reculs élastiques, la spectroscopie Raman, la diffraction de rayons X et la nano-indentation. Il a été trouvé que la température de dépôt améliorait légèrement le degré de relaxation des couches jusqu'à 250 °C, mais qu'elle avait peu d'impact après recuit. Aussi, lors de dépôt à température de la pièce, une forte tension de polarisation réduit l'angle de perte, mais cet effet est encore une fois perdu suite au recuit. Les autres méthodes mentionnées ci-dessus n'ont pas influencé le degré de relaxation des couches selon l'angle de perte, la spectroscopie Raman et la diffraction de rayons X. Cette recherche a été réalisée avec le support financier du CRSNG et du FRQNT (numéro de dossier 206976). / This master's thesis presents the experiments made to reduce the loss angle of tantala coatings similar to those used in LIGO. To improve the relxation level of the coatings they were deposited by magnetron sputtering at temperatures varying from 50 °C to 480 °C. They were also subjected to rapid thermal annealing, and oxygen implantation. In another experiment, the coatings were deposited by magnetron sputtering with substrate biasing varying from 0 V to -450 V at room temperature and at 250 °C. Finally, the coatings of tantala were deposited by high power impulse magnetron sputtering. The loss angle, thickness, roughness, refractive index, atomic composition, stress, the relaxation state and Young's modulus of the coatings were characterized using spectroscopic ellipsometry, Rutherford backscattering, elastic recoil detection, Raman spectroscopy, X-ray diffraction and nanoindentation. It was found that the deposition temperature improved the loss angle until it reached 250 °C. However, annealing the coatings had a superior impact and the influence of the deposition temperature was not visible after annealing. When was applied a high bias to the susbtrate at room temperature, the obtained coating was slightly more relaxed than when a low bias was applied but this effect is, once again, insignificant after annealing. The other methods of deposition mentioned did not improve the loss angle or modify the relaxation state found by Raman spectroscopy and X-ray diffraction of the tantala coatings. This research was made with the financial support of the NSERC and of the FRQNT (file number 206976).

Chemically ordered FePt is one of the most promising materials to reach the ultimate limitations in storage density of future magnetic recording devices due to its high uniaxial magnetocrystalline anisotropy and a corrosion resistance superior to rare-earth based magnets. In this study, FePt and FePt/Cu bilayers have been sputter deposited at room temperature onto thermally oxidized silicon wafers, glass substrates and self-assembled arrays of spherical SiO2 particles with diameters down to 10 nm. Millisecond flash lamp annealing, as well as conventional rapid thermal annealing was employed to induce the phase transformation from the chemically disordered A1 phase into the chemically ordered L10 phase. The influence of the annealing temperature, annealing time and the film thickness on the ordering transformation and (001) texture evolution of FePt films with near equiatomic composition was studied. Whereas flash lamp annealed FePt films exhibit a polycrystalline morphology with high chemical L10 order, rapid thermal annealing can lead to the formation of chemically ordered FePt fifilms with (001) texture on amorphous SiO2/Si substrates. The resultant high perpendicular magnetic anisotropy and large coercivities up to 40 kOe are demonstrated. Simultaneuosly to the ordering transformation, rapid thermal annealing to temperatures exceeding 600 °C leads to a break up of the continuous FePt film into separated islands. This dewetting behavior was utilized to create regular arrays of FePt nanostructures on SiO2 particle templates with periods down to 50 nm. The addition of Cu improves the (001) texture formation and chemcial ordering for annealing temperatures T < 600 °C. In addition, the magnetic anisotropy and the coercivity of the ternary FePtCu alloy can be effectively tailored by adjusting the Cu content. The prospects of FePtCu based exchange spring media, as well as the magnetic properties of FePtCu nanostructures fabricated using e-beam and nanoimprint lithography have been investigated.