Acute myocardial infarction (AMI), caused by ischaemic heart disease (IHD), is a leading cause of death in both men and women in the western society. Hypertension, diabetes, and smoking are examples of well-known risk factors of IHD, but also there are psychosocial factors, such as stress, vital exhaustion (unusual fatigue, irritability, and demoralization) and depression that have been associated with an increased risk in both genders. After an AMI, however, women are more likely than men to be psychosocially impaired resulting in suffering and a presumed increase in the risk of recurrent cardiac events. Psychosocial factors may be targeted in secondary prevention, complementary to drug treatment and conventional lifestyle advice. There is some evidence of beneficial effects on both psychosocial well-being and cardiac outcomes by psychosocial interventions in men. Far fewer women have been studied and the results have been inconsistent. It is not clear how psychosocial factors convey the increased risk of cardiac events, but many possible psychopathological mechanisms, including biochemical and physiological links, have been suggested. In the Women’s Hearts study we have, in a randomised controlled trial, evaluated a one-year cognitive-behavioural stress management programme designed specifically for women with IHD. We included 198 women with IHD, with a mean age of 61 years and from the county of Västerbotten in Northern Sweden, who were randomised to either conventional treatment and follow-up, or to stress management in addition to conventional care. Extensive questionnaires, blood samplings, and biomedical and physiologic data were obtained before randomisation, as well as at follow-ups approximately one and two years after randomisation. Two groups of healthy controls were included for comparisons with women with IHD. Compared to women without IHD, women with IHD reported more stress behaviour and vital exhaustion. Women with IHD also had a lower heart rate variability (HRV) than the healthy controls, possibly reflecting a dysfunctional autonomic nervous regulation of the heart. Reduced HRV has been shown to increase the risk of cardiac arrhythmias and sudden death. At the first follow-up, performed at the end of the one-year stress management programme, women who had participated in the programme had reduced the stress behaviour and vital exhaustion, compared to the women in the conventional care group. We could not find any evidence of a direct cause-effect relationship between stress management and biological cardiovascular risk indicators, or HRV; the intervention and control groups did not differ in insulin resistance, inflammatory, haemostatic and fibrinolytic factors, or HRV. At second follow-up one year later, several additional psychosocial domains were studied. The stress management programme had accelerated psychosocial recovery at the first follow-up over and above that observed in the control group. At the second follow-up, there was further marked improvement in the control group, so the differences in psychosocial variables between the intervention and control groups were no longer significant. In conclusion, a cognitive-behavioural stress management programme could accelerate psychosocial improvement in women with IHD, and thus reduce the amount of psychological and psychosocial suffering. We could not find any evidence that the stress management programme was associated with a concomitant improvement in biological cardiovascular risk indicators, or HRV. Our results suggest that the women with the greatest psychosocial burden should be identified and targeted in new clinical trials of cognitive-behavioural interventions in women with IHD. Future studies within the Women’s Hearts project will evaluate the psychosocial effects at a five-year follow-up, as well as investigations of other possible pathways by which psychosocial interventions might mediate beneficial effects on cardiac events.

The main goal of this dissertation was to show that the principle of atomic layer deposition (ALD) can be applied to “endless” fibers. A reactor of atomic layer deposition has been designed, especially for coating depositions onto meter long bundles of fibers. Aluminum oxide (alumina), titanium oxide (titania), double layers of alumina and titania, as well as aluminium phosphate have been deposited onto bundles of carbon fibers using the home-built reactor. Scanning electron microscopic (SEM) and transmission electron microscopic (TEM) images indicate that the coatings were uniform and conformal onto fiber surface. There was a good adhesion of the coatings to the fibers. Alumina has been deposited using two separate aluminum sources (aluminum trichloride and trimethylaluminum), and water as a source of oxygen. In case of alumina deposition using aluminum trichloride and water, initial deposition temperature was 500 °C. In these conditions, a part of the fiber bundle has been damaged. Thus, the deposition temperature was decreased to 300 °C and the fibers were unaffected. In addition, during this process hydrochloric acid is formed as a byproduct which is a corrosive substance and affects the reactor and there was a chloride impurity in the coatings. Thus, aluminum trichloride precursor was replaced by trimethylalumium. Alumina deposition onto carbon fibers using trimethylaluminum and water was carried out at a temperature of 77 °C. SEM images revealed that the fibers were unaffected and the coatings were uniform and conformal. Oxidation resistance of the carbon fibers was improved slightly after alumina deposition. Oxidation onset temperature of the uncoated fibers was about 630 °C. The resistance was linearly increased with the coating thickness (up to 660 °C) and getting saturated over a thickness of 120 nm. Titania coatings have been deposited using titanium tetrachloride and water. The physical appearances of the titania coatings were similar to the alumina coatings. The oxidation onset temperature of the titania coated carbon fibers was similar to the uncoated fibers but the rate of oxidation was decreased than the uncoated fibers. Two double layer coatings were deposited, alumina followed by titania (alumina/titania), and titania followed by alumina (titania/alumina). If the fibers were coated with the double layer of alumina/titania, they had almost same oxidation onset as alumina coated fibers but the rate of oxidation was decreased significantly compared to alumina coated fibers. This feature is independent of the thickness of the titania layers, at least in the regime investigated (50 nm alumina followed by 13 nm and 40 nm titania). On the other hand, the oxidation onset temperature of fibers coated with titania/alumina (20 nm titania /30 nm alumina) was approximately 750 °C. The fibers were burned completely when temperature was further increased to 900 °C and held another 60 minutes at 900 °C. This is significantly better than any other coating used in this dissertation. ALD of titania and alumina in principle was known beforehand, this dissertation here applies this knowledge for the first time to endless fibers. Furthermore, this dissertation shows for the first time that one can deposit aluminum phosphate via ALD (planar surface as well as fibers). Aluminum phosphate might be special interest in the fiber coating because it is a rather soft material and thus might be used to obtain a weak coupling between fiber and matrix in composites. Aluminum phosphate was deposited using trimethylaluminum and triethylphosphate as precursors. Energy dispersive X-ray spectroscopy and solid state nuclear magnetic resonance spectra confirmed that the coating comprises aluminum phosphate (orthophosphate as well as other stoichiometries). Scanning electron microscopic images revealed that coatings are uniform and conformal. In cases of alumina and titania, it was observed that the coatings were delaminated from the ends of cut fibers and thus formed of clear steps. On the other hand, for aluminum phosphate coating it was observed that the border between coating and underlying fiber often being smeared out and thus formed an irregular line. It seems in case aluminum phosphate cohesion is weaker than adhesion, thus it might be act a weak interface between fiber and matrix. Alumina, titania, and double layer microtubes have been obtained after selective removal of the underlying carbon fibers. The carbon fibers were selectively removed via thermal oxidation in air at temperatures exceeding 550 °C. SEM and TEM images indicate that the inner side of the tube wall has the same morphology like the fibers. In addition, it was observed that the individual microtubes were separated from their neighbors and they had almost uniform wall thicknesses. The longest tubes had a length of 30 cm. / Das Hauptziel dieser Dissertation bestand darin nachzuweisen, dass die Atomlagenabscheidung (engl. atomic layer deposition (ALD)) auf „endlose“ Fasern angewendet werden kann. Es wurde ein Reaktor zur Atomlagenabscheidung gestaltet, der speziell für die Beschichtung meterlanger Faserbündel geeignet ist. Aluminiumoxid, Titanoxid, Doppelschichten aus Aluminiumoxid und Titanoxid sowie Aluminiumphosphat wurden mit Hilfe des selbstgebauten Reaktors auf Kohlefaserbündel abgeschieden. Rasterelektronenmikroskopische (REM) und transmissionselektronenmikroskopische (TEM) Aufnahmen zeigten, dass die Beschichtung auf den Fasern einheitlich und oberflächentreu war. Des Weiteren wurde eine gute Adhäsion zwischen Beschichtung und Fasern beobachtet. Das Prinzip der Beschichtung mit Titanoxid und Aluminiumoxid mit Hilfe der ALD war bereits vorher bekannt und im Rahmen dieser Dissertation jedoch erstmals auf "endlose" Fasern angewendet. Des Weiteren wird in dieser Dissertation erstmals gezeigt, dass es möglich ist, Aluminiumphosphat mittels ALD abzuscheiden (sowohl auf planaren Oberflächen als auch auf Fasern). Aluminiumphosphat könnte von besonderem Interesse in der Faserbeschichtung sein, da es ein relativ weiches Material ist und könnte daher als eine Art „schwacher“ Verbindung zwischen Faser und Matrix in Kompositen dienen. Die Oxidationsbeständigkeit von beschichten Kohlefasern wurde im Vergleich zu unbeschichteten Fasern bis zu einem gewissen Grad erhöht. Monoschichten von Aluminiumoxid und Titanoxid waren dafür wenig effektiv. Aluminiumphosphatbeschichtete Fasern waren deutlich besser geeignet als die beiden anderen. Eine Doppelschicht aus Titanoxid gefolgt von Aluminiumoxid verbesserte die Oxidationsbeständigkeit nochmals deutlich gegenüber allen anderen Beschichtungen, die in dieser Dissertation verwendet wurden. Mikroröhren aus Aluminiumoxid, Titanoxid und Doppelschichten wurden durch die selektive Entfernung der zugrunde liegenden Kohlefasern erhalten. Einzelne Mikroröhren waren von benachbarten Röhren getrennt und sie weisen eine nahezu einheitliche Wanddicke auf.

This thesis describes the deposition of thin films of titanium oxide and Magnéli phases of titanium oxide by atomic layer deposition (ALD) using a novel β-ketoesterate precursor. Titanium oxide is a promising candidate for the high-k dielectric gate oxide layer for CMOS devices in microelectronic circuits. The Magnéli phases of titanium oxide are difficult to grow and stabilize, especially in the thin film form, and have useful properties. The thin film deposition of oxides by CVD/ALD requires suitable precursors, which are often metalorganic complexes. The estimation of vapour pressure using thermogravimetry is described, and employed, using an approach based on the Langmuir equation. This data is important for the evaluation of the suitability of these complexes as CVD precursors. The first chapter gives a brief introduction to the topics that will be discussed in this thesis. Part one of the thesis deals with the synthesis, characterization, and studies of the vapour pressure and partial pressures of the precursors for CVD. This part comprises of the second, third and fourth chapter. The second chapter deals with the synthesis and characterization of the various metalorganic complexes that have been synthesized and characterized to evaluate their suitability as precursors for CVD. The third chapter describes the derivation of vapour pressure of precursors for CVD and ALD, from rising temperature thermogravimetric analysis (TGA) data, using the Langmuir equation. The fourth chapter deals with the determination of partial pressure of CVD precursors using data from low-pressure thermogravimetry. Part Two of the thesis reports the deposition of titanium oxide thin films by ALD, and the detailed investigation of their properties, for application as high-k dielectric materials. Chapters five, six and seven constitute this part. The fifth chapter deals with the deposition of titanium oxide thin films by ALD. Chapter six describes the electrical characterization of the thin films of titanium oxide, for applications as high-k dielectric gate oxide layers for CMOS circuits. In the seventh chapter, the deposition of Magnéli phases of titanium by ALD is described. The dielectric properties of the films are studied.

科学研究費補助金 研究種目:基盤研究(A)(2) 課題番号:08405005 研究代表者:後藤 俊夫 研究期間:1996-1998年度

Since their discoveries, carbon nanotubes have been widely studied, but mostly in the forms of 1D individual carbon nanotube (CNT). From practical application point of view, it is highly desirable to produce carbon nanotubes in large scales. This has resulted in a new class of carbon nanotube material, called the vertically aligned carbon nanotube arrays (VA-CNTs). To date, our ability to design and model this complex material is still limited. The classical molecular mechanics methods used to model individual CNTs are not applicable to the modeling of VA-CNT structures due to the significant computational efforts required. This research is to develop efficient structural mechanics approaches to design, model and characterize the mechanical responses of the VA-CNTs. The structural beam and shell mechanics are generally applicable to the well aligned VA-CNTs prepared by template synthesis while the structural solid elements are more applicable to much complex, super-long VA-CNTs from template-free synthesis. VA-CNTs are also highly “tunable” from the structure standpoint. The architectures and geometric parameters of the VA-CNTs have been thoroughly examined, including tube configuration, tube diameter, tube height, nanotube array density, tube distribution pattern, among many other factors. Overall, the structural mechanics approaches are simple and robust methods for design and characterization of these novel carbon nanomaterials

The mechanisms behind cardiovascular disease (CVD) initiation and progression are not fully elucidated. It is hypothesized that blood flow patterns regulate endothelial cell (EC) function to affect the progression of CVDs. A system that subjects ECs to physiologically-relevant shear stress waveforms within microfluidic devices has not yet been demonstrated, despite the advantages associated with the use of these devices. In this work, a bioreactor was designed to fulfill this need. Waveforms from regions commonly affected by CVDs including were derived. Pump motion and fluid flow profiles were validated by actuator motion tracking, particle image velocimetry, and flowmeters. While several relevant waveforms were successfully replicated, physiological waveforms could not be produced at physiological frequencies owing to actuator velocity and accuracy limitations, as well as dampening effects in the system. Overall, this work lays the foundation for designing a system that provides insight into the role of shear stress in CVD pathogenesis.

The mechanisms behind cardiovascular disease (CVD) initiation and progression are not fully elucidated. It is hypothesized that blood flow patterns regulate endothelial cell (EC) function to affect the progression of CVDs. A system that subjects ECs to physiologically-relevant shear stress waveforms within microfluidic devices has not yet been demonstrated, despite the advantages associated with the use of these devices. In this work, a bioreactor was designed to fulfill this need. Waveforms from regions commonly affected by CVDs including were derived. Pump motion and fluid flow profiles were validated by actuator motion tracking, particle image velocimetry, and flowmeters. While several relevant waveforms were successfully replicated, physiological waveforms could not be produced at physiological frequencies owing to actuator velocity and accuracy limitations, as well as dampening effects in the system. Overall, this work lays the foundation for designing a system that provides insight into the role of shear stress in CVD pathogenesis.

Vanadium oxides are being used as the thermal sensing layer because of their applications in infrared detectors. They have high temperature coefficient of resistance, favorable electrical resistance and compatibility with the MEMS technology. Of all oxides of vanadium, only vanadium dioxide (VO2)has been highly investigated as it shows first order transition (semiconducting to metal transition-SMT)at 68 oC. First order transition is understood as the sharp change in the electrical resistance. The change in resistivity in this case is of the order of 105 over a temperature change of 0.1 oC at 68 oC in a single crystal. Doping vanadium oxides with elements like Mo and W reduce the transition temperature. This is very important for room temperature electrical and optical detection. Though most of the research groups subscribe to PLD, cost-effective methods with large area deposition are major focus of this research. Hence for synthesizing VO2 in bulk and thin films, Solution Combustion Synthesis (SCS), Ultrasonic Nebulized Spray Pyrolysis of Aqueous Combustion Mixture (UNSPACM) Chemical vapour deposition (CVD)and microwave are explored. Synthesis of doped VO2 films in CVD has not been done extensively to yield optical quality thin films. Chapter I surveys the use of phase transition in oxides system for a variety of practical applications. In particular, Vanadium dioxide (VO2) is chosen as it is found to be very useful for infrared and metamaterials based applications. VO2 is known for its first-order semiconducting to metallic transition (SMT). This chapter attempts to explain the influence of processing, doping, annealing, etc on the SMT characteristics. Important aspects such as the idea of hysteresis in VO2 and similarity to martensitic transformation are discussed. The scope and objectives of the thesis are discussed here. Chapter II explains in detail the materials and methods used to synthesize VO2 both in bulk and in thin lm form and methods used to study their characteristics. Brief description on the principle and the working of the home-built experimental set up needed for this study is elicited. In chapter III, attempts were made to understand the phase stability of VO2 and the evolution of crystal structures during the phase transition. VO2 crystallizes in P21/c space group at room temperatures with lattice parameters a=5.752 Ab=4.526 Ac=5.382 Aα=90 β=122.60 γ=90 . Precise control of synthesis parameters is required in stabilizing pure phase in bulk as well as thin lm form. This study focuses on the novel large scale two step synthesis of VO2 using Solution Combustion Synthesis. This involves synthesis of product utilizing redox reaction between metal nitrate and suitable fuel. Generally the products are nanocrystalline in nature due to self-propagation of the exothermic combustion reaction. First step involved the synthesis of V2O5 by combustion reaction between Vanadyl nitrate and urea. In the second step, the as-synthesized V2O5 has been reduced by a novel reduction technique to form monophasic VO2. The presence of competing phases like M1, M2, M3 and R are investigated by XRD, Raman spectroscopy, DSC, Optical and high temperature X-ray diffraction. Chapter IV deals with the reduction in phase transition temperature by doping the SCS synthesized VO2 with W and Mo. Effect of doping on the transition temperature was studied using differential scanning calorimetry (DSC) in both W and Mo. Electrical characteristics of Mo doped VO2 and Optical characteristics of the W-doped VO2 were also studied using four probe resistivity measurements and UV-VIS Spectroscopy respectively. W addition was found to be more effective in reducing the phase transition temperature. To understand further more on the W addition, X-ray photo-electron spectroscopy measurements were performed. W-addition alters the V4+-V4+ bonding and with W addition it is observed that V was present in V3+state. W was present in W6+ state. The addition of W to VO2 introduces more electrons to the systems and disturbs the V4+-V4+ thus reducing the phase transition temperature of VO2. Chapter V describes the large scale, large area deposition of thin films of VO2 by a cost effective method. A novel technique to deposit vanadium dioxide thin films namely, UNSPACM is developed. This simple two-step process involves synthesis of a V2O5 lm on an LaAlO3(LAO) substrate followed by a controlled reduction to form single phase VO2. The formation of M1 phase (P21/c) is confirmed by Raman spectroscopic studies. A thermally activated metal{insulator transition (MIT) was observed at 61 oC, where the resistivity changes by four orders of magnitude. The infrared spectra also show a dramatic change in reflectance from 13% to over 90% in the wavelength range of 7-15 m. This indicates the suitability of the films for optical switching applications at infrared frequencies. A trilayer metamaterial absorber, composed of a metal structure/dielectric spacer/vanadium dioxide (VO2) ground plane, is shown to switch reversibly between reflective and absorptive states as a function of temperature. The VO2 lm, which changes its conductivity by four orders of magnitude across an insulator{metal transition, enables the switching by forming a resonant absorptive structure at high temperatures while being inactive at low temperatures. The fabricated metamaterial shows a modulation of the reflectivity levels of 58% at a frequency of 22.5 THz and 57% at a frequency of 34.5 THz. Chapter VI explains the W doped VO2 thin films synthesized by UN-SPACM. Morphology of the thin films was found to be consisting of globular and porous nanoparticles having size 20 nm. Transition temperature decreased with the addition of W. 1.8 at. %W doping in VO2 transition temperature has reduced upto 25 oC. It is noted that W-doping in the pro-cess of reducing the transition temperature, alters the local structure and also increases room temperature carrier concentration. The presence of W, as was seen in Chapter IV, altered V4+-V4+ bonds and introduced V3+. W was found to be in W6+ state suggesting W addition increased the carrier concentration. Hall Effect measurements suggested the increased carrier con-centration. The roughness of the synthesized films were very high for them to be of de-vice quality, despite encouraging results obtained by electrical measurements. Hence in order to further improve the smoothness and thereby the optical quality of thin films, Chemical Vapour Deposition (CVD) is employed. Chapter VII outlines the effect of processing parameters and post pro-cessing annealing on the semiconductor-metallic transition of VO2. Here in this chapter, the influence of substrate temperature on the SMT properties of VO2 is explored. At different substrate temperatures, the percentage of phase fraction of V in V3+, 4+ and V5+ differed. Besides, the morphology also varied with substrate temperatures. Similarly it is observed that with annealing the VO2 film deposited on glass substrates, SMT properties enhanced which was attributed to filling out of oxygen vacancies. Si based substrates and non-Si based substrates were used for depositing VO2 thin films by CVD. Their temperature coefficient of resistance and SMT properties were studied in order to understand their potential in bolometer and thermal to optical valve based applications. Chapter VIII involves the study of VO2 thin films for thermal to optical valves. ITO coated glass substrates were used for the purpose. Thin films were deposited by both UNSPACM and CVD. It was observed that the reflectivity pro les of the films synthesized by the above said methods were very different. Hence in the process of understanding the huge difference in the reflectivity pro les, classical harmonic oscillator, Lorentzian model was employed to t the experimental data at room temperature whereas Drude-Lorentzian model was used to t the data at higher temperature (at 100 oC- after transition). With this fitting plasma frequencies of the CVD films were calculated. It was observed that defect chemistry of films synthesized by these methods were different. In order to further improve the smoothness of the films, microwave method was proposed in Chapter IX. The preliminary results showed the presence of uniform spheres and 3 D hierarchical structures of VO2 consisting of nanorods. This was extended to deposit VO2 thin films on ITO. DSC and Infrared reflectance pro le of VO2 nanopowder suggested the phase transition. Chapter X summarizes the work done for the thesis and provides insights to the applications and to the future work. The work reported in this thesis has been carried out by the candidate as part of the Ph.D.program. She hopes that this would constitute a worth-while contribution towards development of VO2 thin film technology and its challenges for reliable infrared device applications.

Proprotein Convertase Subtilisin/Kexin 9 (PCSK9) is the ninth member of the Ca+2-dependent mammalian proprotein convertase super family of serine endoproteases that is structurally related to the bacterial subtilisin and yeast kexin enzymes. It plays a critical role in the regulation of lipid metabolism and cholesterol homeostasis by binding to and degrading low-density lipoprotein-receptor (LDL-R) which is responsible for the clearance of circulatory LDL-cholesterol from the blood. Owing to this functional property, there is plenty of research interest in the development of functional inhibitors of PCSK9 which may find important biochemical applications as therapeutic agents for lowering plasma LDL-cholesterol. The catalytic domain of PCSK9 binds to the EGF-A domain of LDL-R on the cell surface to form a stable complex and re-routes the receptor from its normal endosomal recycling pathway to the lysosomal compartments leading to its degradation. Owing to these findings, we propose that selected peptides from PCSK9 catalytic domain, particularly its disulphide (S-S) bridged loop1 323-358 and loop2 365-385, are likely to exhibit strong affinity towards the EGF-A domain of LDL-R. Several regular peptides along with corresponding all- dextro and retro-inverse peptides as well as the gain-of-function mutant variants were designed and tested for their regulatory effects towards LDL-R expression and PCSK9-binding in human hepatic HepG2 and mouse hepatic Hepa1c1c7 cells. Our data indicated that disulfide bridged loop1-hPCSK9323-358 and its H357 mutant as well as two short loop2-hPCSK9372-380 and its Y374 mutant peptides modestly promote the LDL-R protein levels. Our study concludes that specific peptides from the PCSK9 catalytic domain can regulate LDL-R and may be useful for development of novel class of therapeutic agents for cholesterol regulation.

Cette thèse s’inscrit dans le cadre d’un programme de recherche en collaboration avec l’industrie dont l’enjeu est d’utiliser des composites à matrice céramique (CMC) pour la réalisation d’arrière-corps de moteurs pour l’aviation civile.La première partie de ce travail est consacrée à l’étude des fibres de carbure de silicium (Si-C-O) de première génération. Diverses caractérisations physico-chimiques (analyse chimique élémentaire, MEB, MET, spectroscopie Raman, RMN du solide du 29Si et du 13C, DRX…) ont permis d’établir des relations entre la composition chimique, la structure et les propriétés mécaniques des différentes fibres (Nicalon NL série 100 et 200, et Tyranno LoxM, S, ZMI et AM). Une simulation thermodynamique de la phase amorphe intergranulaire SiCxOy a été proposée en s’appuyant sur des données calorimétriques de la littérature obtenues à partir de verres d’oxycarbure de silicium.La seconde partie de ce mémoire est consacrée à l’élaboration par dépôt chimique à partir d’une phase vapeur (CVD) et à la caractérisation de revêtements d’interphase B-C-N. L’influence des conditions d’élaboration (température, pression, composition initiale des gaz) sur la composition chimique des dépôts, leur structure et leur résistance à l’oxydation sous air sec et ambiant a été étudiée. Enfin, les propriétés mécaniques de ces interphases ont été évaluées et des essais de durée de vie ont été réalisés à l’échelle du microcomposite. / This thesis is a part of a research project in partnership with the industry. The aim of the overall project is to design, develop and manufacture exhaust components made of Ceramic Matrix Composites (CMC’s) for civil aircraft engines.The first part of the work deals with the study of first generation silicon carbide fibres (Si-C-O). Various physical and chemical characterizations (quantitative elemental analysis, SEM, TEM, Raman spectroscopy, solid NMR of 29Si and 13C, X-ray diffraction …) were carried out in order to understand the relation between the chemical composition, the structure and the mechanical properties of silicon oxycarbide fibres (Nicalon NL series 100 and 200, and Tyranno LoxM, S, ZMI and AM). Besides, a thermodynamic description of the amorphous SiCxOy phase based on high temperature calorimetry data from the literature is proposed.The second part is devoted to elaboration, by Low Pressure Chemical Vapour Deposition (LP-CVD), and characterization of hexagonal boron carbonitride (B-C-N) coatings. The chemical composition, structure and oxidation resistance (in dry or ambient air) of the coatings were investigated as a function of the deposition conditions (temperature, pressure, initial gas phase composition). Finally, the use of B-C-N coatings as interphases in CMC’s (i.e. their ability to deflect matrix cracks) was investigated by tensile tests on SiC/SiC microcomposites. Their lifetime in static fatigue was also evaluated at 550°C in room atmosphere.