The rapidly expanding wireless market requires low cost, high integration and high performance of wireless communication systems. CMOS technology provides benefits of cost effectiveness and higher levels of integration. However, the design of highly efficient linear CMOS power amplifier that meets the requirement of advanced communication standards is a challenging task because of the inherent difficulties in CMOS technology. The objective of this research is to realize PAs for wireless communication systems that overcoming the drawbacks of CMOS process, and to develop design approaches that satisfying the demands of the industry. In this dissertation, a cascode bias technique is proposed for improving linearity and reliability of the multi-stage cascode CMOS PA. In addition, to achieve load variation immunity characteristic and to enhance matching and stability, a fully-integrated balanced PA is implemented in a 0.18-m CMOS process. A triple-mode balanced PA using switched quadrature coupler is also proposed, and this work saved a large amount of quiescent current and further improved the efficiency in the back-off power. For the low losses and a high quality factor of passive output combining, a transformer-based quadrature coupler was implemented using integrated passive device (IPD) process. Various practical approaches for linear CMOS PA are suggested with the verified results, and they demonstrate the potential PA design approach for WCDMA applications using a standard CMOS technology.

This dissertation focuses on high-performance LC-tank CMOS VCO design at 2 GHz. The high-Q inductors are realized using wiring metal lines in advanced packages. Those inductors are used in the resonator of the VCO to achieve low phase noise, low power consumption, and a wide frequency tuning range. In this dissertation, a fine-pitch ball-grid array (FBGA) package, a multichip module (MCM)-L package, and a wafer-level package (WLP) are incorporated to realize the high-Q inductor. The Q-factors of inductors embedded in packages are compared to those of inductors monolithically integrated on Si and GaAs substrates. All the inductors are modeled with a physical, simple, equivalent two-port model for the VCO design as well as for phase noise analysis. The losses in an LC-tank are analyzed from the phase noise perspective. For the implementation of VCOs, the effects of the interconnection between the embedded inductor and the VCO circuit are investigated. The VCO using the on-chip inductors is designed as a reference. The performance of VCOs using the embedded inductor in a FBGA and a WLP is compared with that of a VCO using the on-chip inductor. The VCO design is optimized from the high-Q perspective to enhance performance. Through this optimization, less phase noise, lower power consumption, and a wider frequency tuning range are obtained simultaneously.

The performance of analog integrated circuits is dependent on the technology. Digital circuits are scalable in nature, and the same circuit can be scaled from one technology to another with improved performance. But, in analog integrated circuits, the circuit components must be re-designed to maintain the desired performance across different technologies. Moreover, in the case of digital circuits, minimum feature-size (short channel length) devices can be used for better performance, but analog circuits are still being designed using channel lengths larger than the minimum feature sizes. The research in this thesis is aimed at understanding the impact of technology scaling and short channel length devices on the performance of analog integrated circuits. The operational amplifier (op amp) is chosen as an example circuit for investigation. The performance of the conventional op amps are studied across different technologies for short channel lengths, and techniques to develop technology-independent op amp architectures have been proposed. In this research, three op amp architectures have been developed whose performance is relatively independent of the technology and the channel length. They are made scalable, and the same op amp circuits are scaled from a 0.25 um CMOS onto a 0.18 um CMOS technology with the same components. They are designed to achieve large small-signal gain, constant unity gain-bandwidth frequency and constant phase margin. They are also designed with short channel length transistors. Current feedback, gm-boosted, CMOS source followers are also developed, and they are used in the buffered versions of these op amps.

The objective of this thesis is to automate the design of round-robin arbiter logic. The resulting arbitration logic is more than 1.8X times faster than the fastest prior state-of-the-art arbitration logic the author could find reported in the literature. The generated arbiter implemented in a single chip is fast enough in 0.25ьm CMOS technology to achieve terabit switching with a single chip computer network switch. Moreover, this arbiter is applicable to crossbar (Xbar) arbitration logic. The generated Xbar, customized according to user specifications, provides multiple communication paths among masters and slaves. As the number of transistors on a single chip increases rapidly, there is a productivity gap between the number of transistors available in a chip and the number of transistors per hour a chip designer designs. One solution to reduce this productivity gap is to increase the use of Silicon Intellectual Property (SIP) cores. However, a SIP core should be customized before being used in a system different than the one for which it was designed. Thus, to reconfigure the SIP core, either an engineer must spend significant effort altering the core by hand or else an enhanced CAD tool can automatically customize the core according to customer specifications. In this thesis, we present SIP generator tools for arbiter and Xbar generation. First, we introduce a Round-robin Arbiter Generator (RAG). The RAG can generate a hierarchical Bus Arbiter (BA) which is faster than all known previous approaches. RAG can also generate a hierarchical Switch Arbiter (SA) which is faster than all known previous approaches. Using a 0.25ьm TSMC standard cell library from LEDA Systems, we show the arbitration time of a 32x32 SA and demonstrate that our SA meets the time constraint to achieve terabit throughput. Furthermore, using a novel token-passing hierarchical arbitration scheme, our 32x32 SA performs better than the Ping-Pong Arbiter and Programmable Priority Encoder by factors of 1.8X and 2.3X, respectively, with less power dissipation. Finally, we present an Xbar switch Generator (X-Gt) tool that automatically configures a crossbar for a multiprocessor System-on-a-Chip (SoC). An Xbar is generated in Register Transfer Level (RTL) Verilog HDL.

Next generation mobile communication systems require the use of linear RF power amplifier for higher data transmission rates. However, linear RF power amplifiers are inherently inefficient and usually require additional circuits or further system adjustments for better efficiency. This dissertation focuses on the development of new efficiency enhancement schemes for linear RF power amplifiers. The multistage Doherty amplifier technique is proposed to improve the performance of linear RF power amplifiers operated in a low power level. This technique advances the original Doherty amplifier scheme by improving the efficiency at much lower power level. The proposed technique is supported by a new approach in device periphery calculation to reduce AM/AM distortion and a further improvement of linearity by the bias adaptation concept. The device periphery adjustment technique for efficiency enhancement of power amplifier integrated circuits is also proposed in this work. The concept is clearly explained together with its implementation on CMOS and SiGe RF power amplifier designs. Furthermore, linearity improvement technique using the cancellation of nonlinear terms is proposed for the CMOS power amplifier in combination with the efficiency enhancement technique. In addition to the efficiency enhancement of power amplifiers, a scalable large-signal MOSFET model using the modified BSIM3v3 approach is proposed. A new scalable substrate network model is developed to enhance the accuracy of the BSIM3v3 model in RF and microwave applications. The proposed model simplifies the modeling of substrate coupling effects in MOS transistor and provides great accuracy in both small-signal and large-signal performances.

This dissertation presents the design and development of a mixed-signal low noise second-order integrated circuit (IC) for the open-loop and closed-loop operation of integrated capacitive micro- and nano-gravity accelerometers. The micromechanical accelerometers are fabricated in thick (less than 100 m) silicon-on-insulator (SOI) substrates. The IC provides the 1-bit digital output stream and has the versatility of interfacing sensors with different sensitivities while maintaining minimum power consumption (less than 5 mW) and maximum dynamic range (90 dB). A fully-differential sampled-data scheme is deployed with the ability of low-frequency noise reduction through the use of correlated double sampling (CDS) scheme. In this work, the measured resolution of the closed-loop CMOS-SOI accelerometer system, in the presence of high background accelerations, is in the micro-g (g: gravity) range. In this design, a second-order SC modulator is cascaded with the accelerometer and the front-end amplifier. The accelerometer operates in air and is designed for non-peaking response with a BW-3dB of 500 Hz. A 22 dB improvement in noise and hence dynamic range is achieved with a sampling clock of 40 kHz corresponding to a low oversampling ratio (OSR) of 40. The interface IC consumed a current of 1.5 mA from a supply of 3 V.

This dissertation focuses on design and implementation of a highly linear and low flicker-noise receiver front-end based on the direct conversion architecture for multiband applications in a CMOS technology. The dissertation consists of two parts: One, implementation of a highly linear RF receiver front-end and, two, implementation of a low flicker-noise RF receiver front-end based for direct conversion architecture. For multiband applications, key active components, highly linear LNAs and mixers, in the RF front-end receiver have been implemented in a 0.18um CMOS process. Theoretical approaches are analyzed from the perspective of implementation issues for highly linear receiver system and are also compared with measured results. Highly linear LNAs and mixers have been analyzed in terms of noise, linearity and power consumption, etc. For a low flicker-noise receiver front-end based on direct conversion architecture, the design of differential LNA and various low flicker-noise mixers are investigated in a standard 0.18um CMOS process. A differential LNA which shows high linearity was fabricated with a low flicker-noise mixer. Three low flicker-noise mixers were designed, measured and compared to the-state-of-the-arts published by other research institutes and companies.

Using bandgap engineering, silicon-germanium (SiGe) BiCMOS technology effectively combines III-V transistor performance with the cost and integration advantages associated with CMOS manufacturing. The suitability of SiGe technology for cryogenic and radiation-intense environments is well known, yet SiGe has been generally overlooked for applications involving extreme high temperature operation. This work is an investigation into the potential capabilities of SiGe technology for operation up to 300°C, including the development of packaging and testing procedures to enable the necessary measurements. At the device level, SiGe heterojunction bipolar transistors (HBTs), field-effect transistors (FETs), and resistors are verified to maintain acceptable functionality across the temperature range, laying the foundation for high temperature circuit design. This work also includes the characterization of existing bandgap references circuits, redesign for high temperature operation, validation, and further optimization recommendations. In addition, the performance of temperature sensor, operational amplifier, and output buffer circuits under extreme high temperature conditions is presented. To the author's knowledge, this work represents the first demonstration of functional circuits from a SiGe technology platform in ambient temperatures up to 300°C; furthermore, the optimized bandgap reference presented in this work is believed to show the best performance recorded across a 500°C range in a bulk-silicon technology platform.

Multiple-input multiple-output (MIMO) radars, which utilize multiple transmitters and receivers to send and receive independent waveforms, have been actively investigated as a next generation radar technology inspired by MIMO techniques in communication theory. Complementary metal-oxide-semiconductor (CMOS) technology offers an opportunity for dramatic cost and size reduction for a MIMO array. However, the resulting formidable signal processing burden has not been addressed properly and remains a challenge. On the other hand, from a block-level point of view, an analog-to-digital converter (ADC) is required for mixed-signal processing to convert analog signals to digital signals, but an ADC occupies a significant portion of a system's budget. Therefore, improvement of an ADC will greatly enhance various trade-offs. This research presents an alternative and viable approach for a MIMO array from a system architecture point of view, and also develops circuit level improvement techniques for an ADC. This dissertation presents a fully-integrated analog pulse compressor (APC) based on an analog matched filter in a mixed signal domain as a key block for the waveform diversity MIMO radar. The performance gain of the proposed system is mathematically presented, and the proposed system is successfully implemented and demonstrated from the block level to the system level using various waveforms. Various figures of merit are proposed to aid system evaluations. This dissertation also presents a low-power ADC based on an asynchronous sample-and-hold multiplying SAR (ASHMSAR) with an enhanced input range dynamic comparator as a key element of a future system. Overall, with the new ADC, a high level of system performance without severe penalty on power consumption is expected. The research in this dissertation provides low-cost and low-power MIMO solutions for a future system by addressing both system issues and circuit issues comprehensively.

The potential of implementing subthreshold radio frequency circuits in deep sub-micron CMOS technology was investigated for developing low-power front-ends for wireless personal area network (WPAN) applications. It was found that the higher transconductance to bias current ratio in weak inversion could be exploited in developing low-power wireless front-ends, if circuit techniques are employed to mitigate the higher device noise in subthreshold region. The first fully integrated subthreshold low noise amplifier was demonstrated in the GHz frequency range requiring only 260 μW of power consumption. Novel subthreshold variable gain stages and down-conversion mixers were developed. A 2.4 GHz receiver, consuming 540 μW of power, was implemented using a new subthreshold mixer by replacing the conventional active low noise amplifier by a series-resonant passive network that provides both input matching and voltage amplification. The first fully monolithic subthreshold CMOS receiver was also implemented with integrated subthreshold quadrature LO (Local Oscillator) chain for 2.4 GHz WPAN applications. Subthreshold operation, passive voltage amplification, and various low-power circuit techniques such as current reuse, stacking, and differential cross coupling were combined to lower the total power consumption to 2.6 mW. Extremely compact resistive feedback CMOS low noise amplifiers were presented as a cost-effective alternative to narrow band LNAs using high-Q inductors. Techniques to improve linearity and reduce power consumption were presented. The combination of high linearity, low noise figure, high broadband gain, extremely small die area and low power consumption made the proposed LNA architecture a compelling choice for many wireless applications.