In this work, the solubility of butyl paraben in 7 pure solvents and in 5 different ethanol-water mixtures has been determined from 1 ˚C to 50 ˚C. The solubility of ethyl paraben and propyl paraben in various solvents has been determined at 10 ˚C. The molar solubility of butyl paraben in pure solvents and its thermodynamic properties, measured by Differential Scanning Calorimetry, have been used to estimate the activity of the pure solid phase, and solution activity coefficients. More than 5000 nucleation experiments of ethyl paraben, propyl paraben and butyl paraben in ethyl acetate, acetone, methanol, ethanol, propanol and 70%, 90% ethanol aqueous solution have been performed. The induction time of each paraben has been determined at three different supersaturation levels in various solvents. The wide variation in induction time reveals the stochastic nature of nucleation. The solid-liquid interfacial energy, free energy of nucleation, nuclei critical radius and pre-exponential factor of parabens in these solvents have been determined according to the classical nucleation theory, and different methods of evaluation are compared. The interfacial energy of parabens in these solvents tends to increase with decreasing mole fraction solubility but the correlation is not very strong. The influence of solvent on nucleation of each paraben and nucleation behavior of parabens in each solvent is discussed. There is a trend in the data that the higher the boiling point of the solvent and the higher the melting point of the solute, the more difficult is the nucleation. This observation is paralleled by the fact that a metastable polymorph has a lower interfacial energy than the stable form, and that a solid compound with a higher melting point appears to have a higher solid-melt and solid-aqueous solution interfacial energy. It has been found that when a paraben is added to aqueous solutions with a certain proportion of ethanol, the solution separates into two immiscible liquid phases in equilibrium. The top layer is water-rich and the bottom layer is paraben-rich. The area in the ternary phase diagram of the liquid-liquid-phase separation region increases with increasing temperature. The area of the liquid-liquid-phase separation region decreases from butyl paraben, propyl paraben to ethyl paraben at the constant temperature. Cooling crystallization of solutions of different proportions of butyl paraben, water and ethanol have been carried out and recorded using the Focused Beam Reflectance Method, Particle Vision and Measurement, and in-situ Infrared Spectroscopy. The FBRM and IR curves and the PVM photos track the appearance of liquid-liquid phase separation and crystallization. The results suggest that the liquid-liquid phase separation has a negative influence on the crystal size distribution. The work illustrates how Process Analytical Technology (PAT) can be used to increase the understanding of complex crystallizations. By cooling crystallization of butyl paraben under conditions of liquid-liquid-phase separation, crystals consisting of a porous layer in between two solid layers have been produced. The outer layers are transparent and compact while the middle layer is full of pores. The thickness of the porous layer can reach more than half of the whole crystal. These sandwich crystals contain only one polymorph as determined by Confocal Raman Microscopy and single crystal X-Ray Diffraction. However, the middle layer material melts at lower temperature than outer layer material. / <p>QC 20130515</p> / investigate nucleation and crystallization of drug-like organic molecules

During development of tissues, cells collectively organize to form complex patterns and morphologies. A general feature of many developing epithelia is their distinct organization into cellular compartments of different cell lineages. The interfaces between these compartments, called compartment boundaries, maintain straight and sharp morphologies. The interfaces play key roles in tissue development and pattern formation. An important model system to study the morphology of compartment boundaries during development is the wing disc of the fruit fly. Two compartment boundaries exist in the fly wing disc, the anteroposterior (AP) boundary and the dorsoventral (DV) boundary. A crucial question is how compartment boundaries are shaped and remain stable during growth. In this work, we discuss the dynamics and mechanisms of compartment boundaries in developing epithelia. We analyze the general features of interfacial phenomena in coarse- grained models of passive and active fluids. We introduce a continuum description of tissues with two cell types. This model allows us to study the propagation of interfaces due to the interplay of cell dynamics and tissue mechanics. We also use a vertex model to describe cellular compartments in growing epithelia. The vertex model accounts for cell mechanics and describes a 2D picture of tissues where the network of adherens junctions characterizes cell shapes. We use this model to study the general physical mechanisms by which compartment boundaries are shaped. We quantify the stresses in the cellular network and discuss how cell mechanics and growth influence the stress profile. With the help of the anisotropic stress profile near the interfaces we calculate the interfacial tension. We show that cell area pressure, cell proliferation rate, orientation of cell division, cell elongation created by external stress, and cell bond tension all have distinct effects on the morphology of interfaces during tissue growth. Furthermore, we investigate how much different mechanisms contribute to the effective interfacial tension. We study the mechanisms shaping the DV boundary in wing imaginal disc at different stages during the development. We analyze the images of wing discs to quantify the roughness of the DV boundary and average cell elongation in its vicinity. We quantify increased cell bond tension along the boundary and analyze the role of localized reduction in cell proliferation on the morphology of the DV boundary. We use experimentally determined values for cell bond tension, cell elongation and bias in orientation of cell division in simulations of tissue growth in order to reproduce the main features of the time-evolution of the DV boundary shape.

Two and three-phase flow processes involving gas, liquid and solid, are common in nature and industry, and include some of the most complex and poorly-understood transport problems. In this research hydrodynamics, heat and mass transfer processes in complex two and three-phase flows were investigated. The interfacial surface area concentration in a short vertical column subject to the through flow of fiber-liquid-gas slurry was experimentally measured using the gas absorption technique. The experimental data were statistically analyzed for parametric effects, and were empirically correlated. The absorption of a gaseous species by a slurry droplet with internal circulation and containing reactive micro-particles was simulated, and parametrically studied. The micro-particles were found to enhance the absorption rate. The absorption rate was sensitive to droplet recirculation, and shrinkage of particles with time resulted in declining absorption rates. The transport of soot particles, suspended in laminar hot gas flowing in a tube, was modeled and parametrically studied. Due to coupled thermal radiation and thermophoresis, a radially-nonuniform temperature profile develops, leading to sharp, non-uniform radial soot-concentration profiles. The assumption of monodisperse particles leads to over-prediction of thermophoresis. The transport and removal of particles suspended in bubbles rising in a stagnant liquid pool were modeled based on a Eulerian – Monte Carlo method. The bubble hydrodynamics were treated in Eulerian frame, using the Volume-of-Fluid (VOF) technique, while particle equations of motion were numerically solved in Lagrangian frame. The bubbles undergo shape change, and have complex internal circulation, all of which influence the particle removal. Model predictions were also compared with experimental data. Using a resemblance between two-phase flow in microchannels, and in large channels at microgravity, a simple Weber number-based two-phase flow regime map was developed for microchannels. Based on the available air-water experimental data, a criterion for the prediction of conditions that lead to flow regime transition out of the stratified-wavy flow pattern in horizontal annular channels was proposed. The thermocapillary effects on liquid-vapor interface shape during heterogeneous bubble ebullition in microchannels were analytically studied.

The European legislation prohibits the use of lead containing solders in Europe. However, lead free solders have a higher melting point (typical 20%) and their mechanical characteristics are worse. Additional problems are aging and adhesion of the solder on the electronic circuits. Thus, research activities must focus on the optimization of the properties of Sn-Ag-Cu based lead free solders chosen by the industry. Two main objectives are treated in this work. In the center of the first one is the study of curious hysteresis effects of metallic cadmium-antimony alloys after thermal cycles by measuring electronic transport phenomena (thermoelectric power and electrical resistivity). The second objective, within the framework of “cotutelle” between the universities of Metz and of Chemnitz and supported by COST531, is to study more specifically lead free solders. A welding must well conduct electricity and well conduct and dissipate heat. In Metz, we determined the electrical conductivity, the thermoelectric power and the thermal conductivity of various lead free solders (Sn-Ag-Cu, Sn-Cu, Sn-Ag, Sn-Sb) as well in the liquid as well in the solid state. The results have been compared to classical lead-tin (Pb-Sn) solders. In Chemnitz we measured the surface tension, the interfacial tension and the density of lead free solders. We also measured the viscosity of these solders without and with additives, in particular nickel. These properties were related to the industrial problems of wettability and spreadability. Lastly, we solidified alloys under various conditions. We observed undercooling. We developed a technique of mixture of nanocristalline powder with lead free solders "to sow" the liquid bath in order to obtain "different" solids which were examined using optical and electron microscopy. / Die europäische Gesetzgebung verbietet die Benutzung von Lötmitteln, die Blei enthalten. Bleilose Lote haben aber einen höheren Schmelzpunkt (typisch 20%) und ihre mechanischen Eigenschaften sind schlechter. Zusätzliche Probleme sind das Alterungsverhalten und das Haftvermögen des Lots an den Leiterbahnen. Daher müssen sich Forschungsaktivitäten auf die Optimierung der Eigenschaften von bleifreien Sn-Ag-Cu (SAC) Loten konzentrieren, die von der Industrie gewählt wurden. Zwei Hauptgebiete werden in dieser Arbeit bearbeitet. Im Zentrum des Ersten stehen seltsame Hysterese-Effekte von metallischen Kadmium- Antimon Legierungen bei thermischen Zyklen, wobei Transporteigenschaften wie die thermoelektrische Kraft und der elektrische Widerstand untersucht werden. Die zweite Aktivität, die in einer Kooperation der Universitäten Metz und Chemnitz (cotutelle) bearbeitet und die durch COST531 unterstützt wird, besteht in der detaillierten Erforschung des Lötprozesses ohne Blei. Eine Lötverbindung muß den Strom gut führen und die Wärme gut ableiten. In Metz haben wir die elektrische Leitfähigkeit, die thermoelektrische Kraft und das Wärmeleitvermögen bestimmt für verschiedene bleilose Lote (Sn-Ag-Cu, Sn-Cu, Sn-Ag, Sn-Sb), sowohl im flüssigen als auch festen Zustand. Die Ergebnisse wurden mit dem klassischen bleihaltigen Lötzinn (Sn-Pb) verglichen. In Chemnitz haben wir die Oberflächen- und Grenzflächenspannung und die Dichte bleifreier Lote gemessen. Ebenfalls wurde die Viskosität dieser Lote ohne und mit Zusätzen (insbesondere Nickel) gemessen. Diese Eigenschaften wurden in Beziehung gesetzt zu den industriellen Problemen der Benetzbarkeit und des Fließverhaltens. Schließlich haben wir Legierungen unter verschiedenen Bedingungen verfestigt. Wir haben Unterkühlung beobachtet. Wir haben eine Technik entwickelt, basierend auf einer Mischung von Lot mit Pulver. Durch "Einsäen" von Nanokristallen in das flüssige Bad erhielten wir "verschiedene" Festkörper, die mit optischer und Elektronenmikroskopie untersucht wurden.

No description available.

Soy flour (SF), a by-product of the soybean oil extraction processing, was investigated for its application in soy-polypropylene composites for interior automotive applications. The emphasis of this work was the understanding of this new type of filler material and the contribution of its major constituents to its thermal stability and impact properties. For this reason, reference materials were selected to represent the protein (soy protein isolate (SPI)) and carbohydrate (soy hulls (SH)) constituents of the soy flour. Additional materials were also investigated: the residue obtained after the protein removal from the soy flour which was called insoluble soy (IS), and the remaining liquid solution after acid precipitation of the proteins, containing mostly sugars and minerals, which was called soluble sugar extract (SSE). Two treatments, potassium permanganate and autoclave, were analyzed for their potential to modify the properties of the soy composite materials. An acid treatment with sulfuric acid conducted on soy flour was also considered. The soy materials were studied by thermogravimetric analysis (TGA) under isothermal (in air) and dynamic (in nitrogen) conditions. SPI had the highest thermal stability and SSE the lowest thermal stability for the early stage of the heating process. Those two materials had the highest amount of residual mass at the end of the dynamic TGA in nitrogen. The two treatments showed minimal effect on the isothermal thermal stability of the soy materials at 200 ??C. A minor improvement was observed for the autoclave treated soy materials. Fourier transformed infrared (FTIR) spectroscopy indicated that the chemical surface composition differed according to type of the soy materials but no difference could be observed for the treatments within one type of soy material. Contact angle analysis and surface energy estimation indicated differences of the surface hydrophobicity of the soy materials according to type of material and treatment. The initial water contact angle ranged from 57 ?? for SF to 85 ?? for SH. The rate of water absorption increased dramatically after the autoclave treatment for IS and SPI. Both materials showed the highest increase in the polar surface energy fraction. In general, the major change of the surface energy was associated with change of the polar fraction. After KMnO4 treatment, the polar surface energy of SF, IS and SPI decreased while SH showed a slight increase after KMnO4 treatment. A relationship between protein content and polar surface energy was observed and seen to be more pronounced when high protein containing soy materials were treated with KMnO4 and autoclave. Based on the polar surface energy results, the most suitable soy materials for polypropylene compounding are SPI (KMnO4), SH, and IS (KMnO4) because their polar surface energy are the lowest which should make them more compatible with non-polar polymers such as polypropylene. The soy materials were compounded as 30 wt-% material loading with an injection moulding grade polypropylene blend for different combinations of soy material treatment and coupling agents. Notched Izod impact and flexural strength as well as flexural modulus estimates indicated that the mechanical properties of the autoclaved SF decreased when compared to untreated soy flour while the potassium permanganate treated SF improved in impact and flexural properties. Combinations of the two treatments and two selected (maleic anhydride grafted polypropylene) coupling agents showed improved impact and flexural properties for the autoclaved soy flour but decreased properties for the potassium permanganate treated soy flour. Scanning electron microscopy of the fractured section, obtained after impact testing of the composite material, revealed different crack propagation mechanisms for the treated SF. Autoclaved SF had a poor interface with large gaps between the material and the polypropylene matrix. After the addition of a maleic anhydride coupling agent to the autoclaved SF and polypropylene formulation, the SF was fully embedded in the polymer matrix. Potassium permanganate treated SF showed partial bonding between the material and the polymer matrix but some of the material showed poor bonding to the matrix. The acid treated SF showed cracks through the dispersed phase and completely broken components that did not bind to the polypropylene matrix. In conclusion, the two most promising soy materials in terms of impact and flexural properties improvement of soy polypropylene composites were potassium permanganate treated SF and the autoclaved SF combined with maleic anhydride coupling agent formulation.

Für eine effiziente und nachhaltige Nutzung von Georeservoiren sind bestmögliche Reservoirmanagementverfahren erforderlich. Oft setzen diese Verfahren auf Tracer-Tests. Dabei enthalten die aufgezeichneten Tracersignale integrale Informationen der Reservoireigenschaften. Tracer-Tests bieten somit eine leistungsfähige Technik zur Charakterisierung und Überwachung der bewirtschafteten Georeservoire. Im Gegensatz zu Tracer-Tests mit konservativen Tracern, welche bereits etablierte Testroutinen zur Verfügung stellen, ist die Verwendung von reaktiven Tracern ein neuer Ansatz. Aufgrund unpassender physikalisch-chemischer Modelle und/oder falschen Annahmen ist die Analyse und Interpretation von reaktiven Tracersignalen jedoch oft verzerrt, fehlinterpretiert oder sogar unmöglich. Reaktive Tracer sind dennoch unersetzbar, da sie durch die gezielte Ausnutzung selektiver und spezifischer Reaktionen mögliche Metriken von Reservoirtestverfahren auf einzigartige Weise erweitern. So liefern reaktive Tracer für ein integriertes Reservoirmanagement geforderten Aussagen über Reservoirmetriken wie z.B. Wärmeaustauschflächen oder in-situ Temperaturen. Um Unsicherheiten bei der Auswertung von Tracerexperimenten zu reduzieren, werden theoretische und experimentelle Untersuchungen zu hydrolysierenden Tracern vorgestellt. Diese Tracer sind durch ihre Reaktion mit Wasser charakterisiert. Einerseits können sie als thermo-sensitive Tracer Informationen über Temperaturen und abgekühlte Anteile eines beprobten Reservoirs liefern. Für die Interpretation von thermo-sensitiven Tracerexperimenten sind die Kenntnis der zugrunde liegenden Reaktionsmechanismen sowie bekannte Arrhenius-Parameter Voraussetzung, um die verwendete Reaktion pseudo erster Ordnung nutzen zu können. Darüber hinaus ermöglichen die verwendeten Verbindungen durch ihre Fluoreszenzeigenschaften eine Online-Messung. Um die Empfindlichkeit und praktischen Grenzen thermo-sensitiver Tracer zu untersuchen, wurden kontrollierte Laborexperimente in einem eigens dafür entwickelten Versuchsaufbau durchgeführt. Dieser besteht aus zwei seriell geschalteten Säulen, die beide mit Sand gefüllt sind und jeweils auf eine eigene Temperatur eingestellt werden können. Somit ist es möglich, verschiedene thermische Einstellungen zu betrachten. Die untersuchten experimentellen Szenarien imitieren größtenteils Feldanwendungen: Durchflussexperimente sowie auch Experimente mit einer Umkehr der Fließrichtung. Darüber hinaus wurde untersucht, ob thermo-sensitive Tracer auch sensitiv gegenüber der Position der Temperaturfront sind. Dabei wurden die Tracer kontinuierlich oder gepulst injiziert. Die Ergebnisse bestätigen die zugrunde liegende Theorie experimentell. Wenn die pH-Abhängigkeit der Hydrolyse bei der Analyse berücksichtigt wird, kann eine Temperaturschätzung mit einer Genauigkeit und Präzision von bis zu 1 K erreicht werden. Die Schätzungen sind von Verweilzeit und gemessenen Konzentrationen unabhängig. Weiterhin lässt sich eine Schätzung über den ausgekühlten Anteil des Systems erhalten. Durch die steuerbaren und definierten Laborbedingungen ist es erstmals möglich, die geforderte Anwendbarkeit von thermo-sensitiven Tracern belastbar nachzuweisen. Des Weiteren wird eine zweite Anwendung hydrolysierender Tracer vorgeschlagen. Beim Lösen von CO2 für „Carbon Capture and Storage“-Anwendungen hängt die Effizienz maßgeblich von der Grenzfläche zwischen CO2 und der Sole in tiefen Reservoiren ab. Somit ist diese Metrik wichtig, um die Effizienz der CO2 Auflösung in Wasser zu bewerten. Die gezielt entwickelten Kinetic-Interface-Senitive-Tracer (KIS-Tracer) nutzen, zusätzlich zur Hydrolyse an der Grenzfläche, die unterschiedlichen Lösungseigenschaften von Tracer und Reaktionsprodukt im entsprechenden Fluid. Somit lassen sich potentiell Aussagen über die Dynamik der Grenzfläche machen. Neben dem grundlegenden Konzept sowie den theoretischen Tracer-Anforderungen wird eine erste Anwendung im Laborexperiment vorgestellt. Diese zeigt das erfolgreiche, zielorientierte Moleküldesign und bietet eine experimentelle Basis für ein makroskopisches numerisches Modell, mit welchem numerische Simulationen verschiedener Testszenarien durchgeführt werden, um das Zusammenspiel von KIS-Tracer und dynamischer Grenzfläche zu untersuchen. Aufgrund der Temperaturabhängigkeit der Reaktionsgeschwindigkeit hydrolysierender Tracer werden in der Regel auch thermische Signale aufgezeichnet. Der letzte Teil prüft die Möglichkeit, Informationen aus den aufgezeichneten Temperaturen zu extrahieren. Für ein idealisiertes Einzelkluftsystem wird eine Reihe von analytischen Lösungen diskutiert. Aus thermischen Injektion-/Entzugsversuchen können damit räumliche und zeitliche Profile abgeleitet werden. Mit der Verwendung von mathematisch effizienten Inversionsverfahren wie der iterativen Laplace-Transformation lassen sich rechentechnisch effiziente Realraum-Lösungen ableiten. Durch die Einführung von drei dimensionslosen Kennzahlen können die berechneten Temperaturprofile auf Bruchbreite oder Wärmetransportrate, wechselnde Injektions-/ Pumpraten und/oder auf in der Nähe beobachtbare räumliche Informationen analysiert werden. Schließlich werden analytische Lösungen als Kernel-Funktionen für nichtlineare Optimierungsalgorithmen vorgestellt. Zusammenfassend bearbeitet die vorliegende Arbeit den Übergang zwischen Tracerauswahl und Traceranwendung. Die Ergebnisse helfen Planungs- und Analyseunsicherheiten zu reduzieren. Dies wird bezüglich der Empfindlichkeit gegenüber Temperaturen, Kühlungsanteilen, flüssig/flüssig-Grenzfläche, Kluftbreite und Wärmetransportrate gezeigt. Somit bieten die vorgestellten Tracerkonzepte neue Metriken zur Verbesserung von Reservoirmanagementverfahren. Die experimentellen Ergebnisse und die neuen analytischen Modelle ermöglichen einen tiefen Einblick in die kollektive Rolle der Parameter, welche die Hydrolyse und den Wärmetransport in Georeservoiren kontrollieren.

This thesis describes the study on structure and dynamics of various kinds of molecular membranes in general. We have studied the morphological transition of colloidal as well as biologically relevant membranes and qualitatively argued regarding the interplay between structure and dynamics. Systematic measurements have been performed to address the issue of ambiguous behavior of molecules under stress when its confined at the interface. The structural and dynamical effect on interfacial membranes have been studied for soft colloidal free standing langmuir monolayer as well as for the quasi two dimensional lipid membranes on solid supports. For organic nanoparticle monolayer we have observed a correlation between the nanoparticle raft dynamics and the underlying morphological transition. In this study we have also found a non-monotonic behavior of dynamical heterogeneity with time which is unusual for a colloidal system in common and beyond the prediction of Mode Coupling Theory. In the case of lipid membrane, we have given an experimental evidence of lipid molecular rearrangement process at molecular level when its perturbed by foreign entities. Using sophisticated X-Ray scattering techniques, we were able to capture the subtle changes happening in the assembly of lipid molecules in a planar bilayer structure when it interacts with molecules having biological relevance. In the next level we have used lipid membranes as an active plat-form to study the physical interaction with several kinds of nanoparticles and explored the mechanism of active participation of lipid molecules in self assembly process. Besides with the help of Fluorescence Correlation Spectroscopy, we have also studied the effect of nanoparticles assemblies on the dynamics of lipid molecules itself. In Chapter 1, we have provided the background along with a brief review of the existing literature for understanding the results represented in the subsequent chapters. This includes discussion on the various physical properties of our systems of interest, including dynamic behavior of colloidal particles in different concentration regime and a detailed theoretical understanding regarding the glass transition and jamming transition for a highly dense colloidal packing. In this section we have also discussed the advantages of interfacial microrheology technique over conventional bulk rheology in terms of efficiency and sensitivity. Here we have also pointed out the formulation of the multi-particle tracking method for achieving different parameters which are correlated in space and time for a given system. Followed by that the Dynamical Susceptibility and the anomaly in Van Hove correlation function, for a heterogeneous system has been argued thoroughly. Towards the end we have discussed about the general features of another type of two dimensional membrane i.e. the lipid membrane at interface. Using raft theory we have also tried to give a plausible explanation of the dynamical heterogeneity of the real cell membrane which is mimicked by the model supported lipid membrane. Here we have argued about the structural six fold symmetry of a compact monolayer. Finally in the last part we have summarized the theoretical aspects of the lipid molecule mediated self assembly process and the how the lipid diffusion plays a vital role in it. Chapter 2 deals with the aspect of measuring the morphological transition and its effect on the dynamics for a two dimensional membrane at air/water interface. It starts with the discussion on the synthesis method for various types of organic molecule grafted nanoparticles like Cadmium Selenide(CdSe Quantum Dots) and Gold Nanoparticle(Au NPs) of different size and properties and followed by a preparation method of 2D film at air/water interface and on solid substrate using Langmuir-Blodgett method. In this chapter we have discussed about the basic principles of several experimental tools like Brewster Angle Microscopy(BAM), Laser Scanning Confocal Microscopy(LSCM), Atomic Force Microscopy(AFM), Thermogravimetric Analysis(TGA), X Ray Reflectivity(XRR), Grazing Incidence Diffraction(GID), Fluorescence Correlation Spectroscopy(FCS) etc. Chapter 3 explains the main aspects of the microscopic dynamics in dense amorphous nanoparticle monolayer at the air-water interface. In this study we have found a transition in mechanical properties, tracked down through the systematic variation of isothermal compressibility(�) with increasing two dimensional packing fraction of nanoparticle rafts up to the area fraction of Φ∼0.82 using Laser Scanning Confocal Microscope. Here we have used multi particle tracking method for a close packed gold monolayer with CdSe tracer to estimate different dynamical properties like Mean Square Displacement(MSD), Dynamical Heterogeneity etc. These calculations indeed point out the non-monotonic variation of the amplitude in the four-point dynamic susceptibility (χ4), a signature of spatio-temporal extension of correlated domains. Along with that we have also observed the anomaly in trend for the inherent relaxation time τ∗with increasing area fraction(Φ). Interestingly the variation in χ4exactly follows the systematic we found for the isothermal compressibility( �) with increasing Φ and that indicates the connection between the observed macroscopic transitions in mechanical properties and the microscopic dynamical phase transitions. Finally we have given a possible explanation of these kind of events in terms of the interaction between this sterically stabilized nanoparticle domains with the help of interpenetration of the capping long chain polymers of the neighboring nanoparticle. Chapter 4 opens up the possibilities of probing the hidden features of biomembranes at molecular scale with the help of very precise techniques based on synchrotron X ray diffraction. Here we have studied the rearrangement of the lipid molecules of an artificial membrane on a solid support as an effect of ad-sorption of organic branched molecules. In this work we have used non toxic PETIM dendrimers of two different generations, i.e. G3and G4which differs a lot in terms of size, no of termination groups, molecular weights and protonation states. Our initial measurements shows quantitatively the in-plane and out of plane symmetry breaking of the lipid bilayer as a result of the interaction with these two types of molecules. The molecular adsorption effect was quantified in terms of thickness reduction and the change in the scattering length density(SLD) or the electron density of the top layer in out of plane reflectivity model. Interestingly both the dendrimers showed different behavior and the interaction reflected in terms of membrane penetration was found stronger for higher generation. On the other hand the GID measurement indicates an enhancement of the in plane unit cell dimension and associated parameters of the arrangement of lipid molecules as a result of interaction with dendrimers. The combined XRR and GID measurements indicate a local fluidization of lipid packing as an outcome of charged branched molecules adsorption on the membrane surface. Chapter 5 is summarizes the lipid mediated self assembly process of nanoparticles on a bilayer and how the interaction changes the local properties of the bilayer represented by the molecular diffusivity. In this study we have used particles of wide variety of features in terms of size, charge, functionality, polarity etc and found a quite dramatic effect in the nanoparticle adsorption event on a solid supported Lαphased DMPC lipid bilayer. We have also seen that de-pending on the concentration and amount of surface charge the nanoparticles form two dimensional regular self assembled patterns on the bilayer surface. In FCS measurement, we have also found a second group of dynamics ( distribution of diffusivity) along with the normal bilayer diffusion which has been identified as the diffusion of the lipid molecules where nanoparticles are adsorbed. The inherent increment in diffusivity supports the argument of local fluidization in lipid membrane in presence of charged nanoparticle as we have observed in our XRR and GID data described in chapter 4. Chapter 6 contains the summary and the future perspective of the work presented here.

This thesis deals with the dynamics of a thin liquid film falling down a heated plate. The heating yields surface tension gradients that induce thermocapillary stresses on the free surface, thus affecting the stability and the evolution of the film. Accounting for the coherence of the flow due to viscosity, two main approaches that reduce the dimensionality of the original problem are usually considered depending on the flow rate (as measured by the Reynolds number): the `long wave' asymptotic expansion for small Reynolds numbers and the `integral boundary layer' approximation for moderate Reynolds numbers. The former suffers from singularities and the latter from incorrectness of the instability threshold for the occurrence of hydrodynamic waves. Thus, the aim of this thesis is twofold: in a first part, we define quantitatively the validity of the `long wave' evolution equation (Benney equation) for the film thickness h including the thermocapillary effect; and in a second part, we improve the `integral boundary layer' approach by combining a gradient expansion to a weighted residual method. <p>In the first part, we further investigate the Benney equation in its validity domain in the case of periodically inhomogeneous heating in the streamwise direction. It induces steady-state deformations of the free surface with increased transfer rate in regions where the film is thinner, and also in average. The inhomogeneities of the heating also modify the nature of travelling wave solutions at moderate temperature gradients and allows for suppressing wave motion at larger ones.<p>Moreover, large temperature gradients (for instance positive ones) in the streamwise direction produce large local film thickening that may in turn become unstable with respect to transverse disturbances such that the flow may organize in rivulet-like structures. The mechanism of such instability is elucidated via an energy analysis. The main features of the rivulet pattern are described experimentally and recovered by direct numerical simulations.<p>In the second part, various models are obtained, which are valid for larger Reynolds numbers than the Benney equation and account for second-order viscous and inertial effects. We then elaborate a strategy to select the optimal model in terms of linear stability properties and existence of nonlinear solutions (solitary waves), for the widest possible range of parameters. This model -- called reduced model -- is a system of three coupled evolution equations for the local film thickness h, the local flow rate q and the surface temperature Ts. Solutions of this model indicate that the interaction of the hydrodynamic and thermocapillary modes is non-trivial, especially in the region of large-amplitude solitary waves.<p>Finally, the three-dimensional evolution of the solutions of the reduced model in the presence of periodic forcing and noise compares favourably with available experimental data in isothermal conditions and with direct numerical simulations in non-isothermal conditions.<p><p>------------------------------------------------<p><p>Cette thèse analyse la dynamique d'un film mince s'écoulant le long d'une paroi chauffée. Le chauffage crée des gradients de tension superficielle qui induisent des tensions thermocapillaires à la surface libre, altérant ainsi la stabilité et l'évolution du film. Grâce à la cohérence de l'écoulement assurée par la viscosité, deux approches permettant de réduire la dimensionnalité du problème original sont habituellement considérées suivant le débit (mesuré par le nombre de Reynolds): l'approximation asymptotique dite `longues ondes' pour les faibles nombres de Reynolds et l'approximation `intégrale couche limite' pour les nombres de Reynolds modérés. Cependant, la première approximation souffre de singularités et la dernière de prédictions imprécises du seuil de stabilité des ondes hydrodynamiques à la surface du film. Le but de cette thèse est donc double: dans une première partie, il s'agit de déterminer, de manière quantitative, la validité de l'équation d'évolution `longues ondes' (ou équation de Benney) pour l'épaisseur du film h, en y incluant l'effet thermocapillaire; et dans une seconde partie, il s'agit d'améliorer l'approche `intégrale couche limite' en combinant un développement en gradients avec une méthode aux résidus pondérés.<p>Dans la première partie, nous étudions l'équation de Benney, dans son domaine de validité, dans le cas d'un chauffage inhomogène et périodique dans la direction de l'écoulement. Cela induit des déformations permanentes de la surface libre avec un accroissement du transfert de chaleur dans les régions où le film est plus mince, mais aussi en moyenne. Un chauffage inhomogène modifie également la nature des solutions d'ondes progressives pour des gradients de températures modérés et conduit même à leur suppression pour des gradients de températures plus importants. De plus, ceux-ci, lorsqu'ils sont par exemple positifs le long de l'écoulement, produisent des épaississements localisés du film qui peuvent à leur tour devenir instables par rapport à des perturbations suivant la direction transverse à l'écoulement. Ce dernier s'organise alors sous forme d'une structure en rivulets. Le mécanisme de cette instabilité est élucidé via une analyse énergétique des perturbations. Les principales caractéristiques des structures en rivulets sont décrites expérimentalement et retrouvées par l'intermédiaire de simulations numériques. <p>Dans la seconde partie, nous dérivons une famille de modèles valables pour des nombres de Reynolds plus grands que l'équation de Benney, qui prennent en compte les effets visqueux et inertiels du second ordre. Nous élaborons ensuite une stratégie pour sélectionner le modèle optimal en fonction de ses propriétés de stabilité linéaire et de l'existence de solutions non-linéaires (ondes solitaires), et ce pour la gamme de paramètres la plus large possible. Ce modèle -- appelé modèle réduit -- est un système de trois équations d'évolution couplées pour l'épaisseur locale de film h, le débit local q et la température de surface Ts. Les solutions de ce modèle indiquent que l'interaction des modes hydrodynamiques et thermocapillaires n'est pas triviale, spécialement dans le domaine des ondes solitaires de grande amplitude. Finalement, l'évolution tri-dimensionnelle des solutions du modèle réduit en présence d'un forçage périodique ou d'un bruit se compare favorablement aux données expérimentales disponibles en conditions isothermes, ainsi qu'aux simulations numériques directes en conditions non-isothermes<p> / Doctorat en sciences appliquées / info:eu-repo/semantics/nonPublished

As advances in thin films are made there is a parallel requirement to develop equipment capable of measuring their properties accurately and consistently. In addition there is a need to understand the parameters that are measured. Typical DPI measurements allow both the refractive index (related to density) and the thickness of the adsorbed layer to be calculated with relatively few assumptions, to a very high precision in real time. This thesis presents the research undertaken to develop multiple path length dual polarisation interferometry (MPL-DPI) and absorption enhanced dual polarisation interferometry (AE-DPI). In addition research is presented that can be used to improve the interpretation of the measured parameters for inhomogeneous films and uniaxial films. The new Interferometric technique MPL-DPI allows the thickness and refractive index of in situ and ex-situ coated ultra-thin films to be measured. The procedures and the mathematics required to calculate the properties of films have been described and the technique verified. The technique was demonstrated using films of PMMA, where good agreement was found with complementary techniques. Furthermore, some key features of MPL-DPI were demonstrated using the measurements of interfacially grafted acrylic acid. The absorption enhanced DPI uses the attenuation of the light within the waveguide, due to the light absorbing properties of a film on its surface. As the composition of a film changed, it was shown that the refractive index and extinction coefficients could be used to separate the mass of the components of the film that absorbed light, from the components of the film that did not. With the use of a semi-uniaxial model, the extra data from the attenuation in two polarisations was used to fit the extraordinary and ordinary extinction coefficients. The extraordinary and ordinary extinction coefficients were used to demonstrate that molecular orientation could be implied. The influence that an inhomogeneous film has on the measured thickness, refractive index and extinction coefficient fitted by homogeneous models were investigated. Formulas are presented to explain the thickness, refractive index and extinction coefficient of the measured film. A formula for the total mass per unit area that uses the refractive index was created to account for films that contain molecules of different refractive index increments (dn/dc's). To separate the mass of the individual molecular species from the total mass per unit area, formulas that use the extinction coefficient were derived so molecules that absorb light could be separated from those that do not. The mass calculated from the refractive index and the mass calculated from the extinction coefficient were also examined for uniaxial films. For uniaxial films both measures of the adsorbed mass were found to be relatively accurate and benefited from a partial cancellation of errors. The accuracy of the measurements made by dual polarisation interferometry technology is systematically examined throughout this thesis. Improvements in the calibration routines are suggested and a procedure for the identification and reduction of errors in the phase and contrast is demonstrated.