Over the last decade, electronics operating at high temperatures have been increasingly demanded to support in situ sensing applications such as automotive, deep-well drilling and aerospace. However, few of these applications have requirements above 460 °C, as the surface temperature of Venus, which is a specific target for the seismic sensing application in this thesis. Due to its wide bandgap, Silicon Carbide (SiC) is a promising candidate to implement integrated circuits (ICs) operating in such extreme environments. In this thesis, various analog and mixed-signal ICs in 4H-SiC bipolar technology for high-temperature sensing applications are explored, in which the device performance variation over temperatures are considered. For this purpose, device modeling, circuit design, layout design, and device/circuit characterization are involved. In this thesis, the circuits are fabricated in two batches using similar technologies. In Batch 1, the first SiC sigma-delta modulator is demonstrated to operate up to 500 °C with a 30 dB peak SNDR. Its building blocks including a fully-differential amplifier, an integrator and a comparator are characterized individually to investigate the modulator performance variation over temperatures. In the succeeding Batch 2, a SiC electromechanical sigma-delta modulator is designed with a chosen Si capacitive sensor for seismic sensing on Venus. Its building blocks including a charge amplifier, a multiplier and an oscillator are designed. Compared to Batch 1, a smaller transistor and two metal-interconnects are used to implement higher integration ICs in Batch 2. Moreover, the first VBIC-based compact model featured with continuous-temperature scalability from 27 to 500 °C is developed based on the SiC transistor in Batch 1, in order to optimize the design of circuits in Batch 2. The demonstrated performance of ICs in Batch 1 show the feasibility to further develop the SiC readout ICs for seismic sensor system operating on Venus. / <p>QC 20170911</p>

Maps and models of seismic and tsunami risk are constructed from a variety of measurements taken in Indonesia, which have the potential to reduce loss of life and infrastructure. The first study uses the multichannel analysis of surface waves (MASW) method to calculate the time-averaged shear wave velocity to 30 m depth (Vs30). These measurements were taken at 58 sites in the city of Pacitan, Java and on the islands of Lombok, Ambon, and the Banda Islands. Vs30 calculations are compared with local geologic maps to extrapolate site class for locations not measured directly. Site class maps are then compared with Modified Mercalli Intensity (MMI) observations for three earthquake events that impacted Lombok and Ambon to identify regions where the MMI and Vs30 do and do not corroborate one another. Consistent with other Vs30 studies, the lowest values are observed on coastal alluvial plains and the highest values on steeper hillsides underlain by volcanic deposits. The second study focuses on a potential sector collapse of the volcano Banda Api within the Banda Islands. A field survey of its summit identified a steeply dipping normal fault striking NNE-SSW. This, along with the fissure geometry of the volcano's most recent eruption, reveals a failure plane along which a future sector collapse could occur. The numerical model Tsunami Squares (TS) predicts that the tsunami produced by this landslide would inundate an estimated 63% of buildings on the Banda Islands with waves as high as 82 m. These findings highlight the importance of installing a GPS receiver array on Banda Api to monitor the motion of its slopes. The third study analyzes sediment from trenches on the Banda Islands and Ambon to test if historical tsunamis that have impacted the area are preserved in the geological record. Potential tsunami deposits were identified by the presence of marine sand and larger clasts of marine carbonate in an environment which otherwise lacks large storms to bring such material onshore. Several dating methods constrain the ages of at least seven candidate tsunami deposits found in trenches onshore. One of these historical tsunamis (the event of November 26, 1852) is described in significant detail from several locations across the Banda Sea, which enables modeling of the event using a Bayesian statistical approach. The posterior of this model predicts the most likely epicenter was SW of Seram with a mean magnitude of Mw 8.8. It also makes other predictions about fault parameters. The region exhibits a marked slip deficit based on instrumental records of earthquakes in the area.

This diploma thesis deals with processes of electrical circuits calculations in the last years' worldwide standards like Dymola, MATLAB, Maple or SPICE applications. Circuits calculations are linked with methods for solving linear differential equations, used in this work also by verification of functionality of designed models for CMOS inverter, CMOS NAND, CMOS NOR. Numerical integration method in combination with Taylor series is a suitable method also for parallel calculations of CMOS VLSI circuits. CMOS circuits simulation was implemented with this method in applications in MATLAB language, solving circuits, represented by differential equations. Functionality of the applications was verified by some real examples. Significant acceleration of calculations using Taylor series compared to other methods is an important factor in choosing methods used in circuit simulations.

Dissertation thesis is focused on using alternative energy sources called energy harvesting. This thesis offers a solution to problems with autonomous powering of sensor networks if primary power source recovery is impossible. In these cases, energy of the external power (e.g. temperature, light, motion) should be used. Proposed solution should be especially used in the field of medical applications (e.g. cochlear implants, pacemakers, insulin pumps). Long time monitoring of the personal health status is also possible when employing automated sensor systems. In this work, there is state of art review relating to the low power energy sources for an alternative powering of sensor systems. It was observed that existing systems are almost prepared for the implementation of energy harvesting power sources. The energy harvesting power sources have been developed by numerous researcher teams around the world, but there are only a few variants of power management circuits for effective energy gaining, storing and using. This area has a huge potential for the next research. The issues regarding to the distribution of gained energy are solved on the complex level in the thesis. For these purposes, a new simulation model of the whole system (fully implantable artificial cochlea) including its subcircuits was developed in the SPICE environment. It connects independent subcircuits into a single comprehensive model. Using this model, a few novel principles for energy distribution (e.g. Charge Push Through technique) was developed. In the near future, these techniques are also applicable to the design of versatile sensor systems.

This work aims to design process of integrated circuits on the transistor level, specially using evolutionary algorithm. For this purpose it is necessary to choose reasonable level of abstraction during simulation, which is used for evaluation candidate solutions by fitness function. This simulation has to be fast enough to evaluate thousands of candidate solutions within seconds. This work discusses already used techniques for transistor level circuit design and it chooses useful parts for new design of faster and more reliable automated design process, which would be able to design complex logic circuits. The thesis also discusses implementation of this system and used approach with regard to encountered problems in transistor-level circuit design and optimization by evolution.

Es wird ein Verfahren zur lokalisierten elektrochemischen Abscheidung metallischer Strukturen aus Kapillarsonden vorgestellt. Der experimentelle Aufbau, die Herstellung der Sonden, das Arbeiten im Nahfeld der Probe (Scherkraft-Abstandsdetektion)sowie die verschiedenen Beschaltungmöglichkeiten der elektrochemischen Zelle werden ausführlich beschrieben. Ergänzend zu den experimentellen Arbeiten werden einerseits numerische Simulationen gezeigt, die zur Veranschaulichung der Potentialverteilung in der Apexregion dienen und qualitativ beschreiben, wie sich das Schichtdickenprofil der abgeschiedenen Strukturen mit den einstellbaren Parametern (Elektrodenpotentiale, Spitze-Probe-Abstand) variieren läßt. Andererseits werden die verschiedenen Beschaltungsmöglichkeiten der Zelle anhand von Schaltungssimulationen verglichen und so die Wahl des günstigsten Arbeitspunktes für die in den Experimenten verwendete (bi)-potentiostatische Abscheidung diskutiert. Mit dieser Anordnung wurden lokalisiert Cluster in einer porösen Aluminiumoxidmembran deponiert und anschließend abgebildet. In weiteren Strukturierungsversuchen wurden Kupfer bzw. Gold lokalisiert elektrochemisch auf ITO abgeschieden, wobei das Schichtwachstum simultan optisch in Transmission beobachtet wurde. Es werden u.a. Strukturen erzeugt, deren laterale Abmessungen kleiner als der Kapillardurchmesser sind (Fokussierung, max. Verhältnis 8:1). Die derzeit kleinsten elektrochemisch erzeugbaren Strukturen haben eine laterale Ausdehnung von ca. 5 Mikrometern. / A method for the localized electrochemical deposition of metal structures using capillary tips is presented. The experimental set-up, the tip preparation, the distance detection in near-field operation (shear-force detection), as well as the different types of circuiting of the electrochemical cell are described in detail. In addition to the experimental work, numerical simulations for the qualitative visualization of the potential distribution around the apex region show, how the films thickness profile can be adjusted with the variable parameters (electrode voltages, tip-sample distance). Circuit simulations of the electrochemical cell allow to pre-estimate the optimum working conditions for the used (bi)-potentiostatic electrode set-up. With this method, clusters have been deposited in a thin film of porous alumin oxide and imaged in shear-force mode. Gold and copper structures have been deposited on ITO, while the film growth was observed optically. The lateral dimension of the deposited structures can be smaller than the inner diameter of the capillaries (maximum focus: 8:1). The smallest structures produced in this work have lateral dimensions of 5 micrometers.

Silicon Carbide (SiC), owing to its large bandgap, has proved itself to be a very viable semiconductor material for the development of extreme temperature electronics. Moreover, its electrical properties like critical field (Ecrit) and saturation velocity (vsat) are superior as compared to the commercially abundant Silicon, thus making it a better alternative for RF and high power applications. The in-house SiC BJT process at KTH has matured a lot over the years and recently developed devices and circuits have shown to work at temperatures exceeding 500˚C. However, the functional reliability of more complex circuits requires the use of simulators and device models to describe the behavior of constituent devices. SPICE Gummel Poon (SGP) is one such model that describes the behavior of the BJT devices. It is simpler as compared to the other models because of its relatively small number of parameters. A simple semi-empirical DC compact model has been successfully developed for low voltage applications SiC BJTs. The model is based on a temperature dependent SiC-SGP model. Studies over the temperature dependences for the SGP parameters have been performed. The SGP parameters have been extracted and some have been optimized over a wide temperature range and they have been compared with the measured data. The accuracy of the developed compact model based on these parameters has been proven by comparing it with the measured data as well. A fairly accurate performance at the required working conditions and correlation with the measured results of the SiC compact model has been achieved.

Abstract Software process assessment and improvement came under the spotlight in the discussion of software engineering when the Software Engineering Institute published the maturity model for software process capability determination in 1987. Since then, several new approaches and standards have been developed. This thesis introduces a European software process assessment and improvement methodology called BOOTSTRAP, which was initially developed in an ESPRIT project starting from lean and kaizen philosophy. The focus is on the evolution of methodology and how it was developed, using an experimental research approach. The work covers also enhancements to the methodology investigated in the SPICE, PROFES and TAPISTRY projects. The enhancements expand the original methodology into new specific application areas, keep it compliant with new quality standards and certification, improve the efficiency of the assessment method, enhance the focus from process to product and strengthen improvement monitoring and support. To address these areas, the new BOOTSTRAP methodology releases offer tailored and enhanced assessment reference models and enhanced assessment and improvement methods. The new features also facilitate more frequent and even continuous assessments with software measurement-based indicators. The thesis explains the origin and features of BOOTSTRAP software process assessment and improvement methodology and how it was developed for professional use. The discussion starts with the evolution of the methodology. Then the new trends and demands are introduced and new features of the BOOTSTRAP methodology described. The conclusion discusses how the methodology developed to be able successfully to support professional software process assessment, to align it with the evolution of software engineering, to adopt the features and requirements of the underlying standards in order to conform to the requirements set by ISO 15504 standard and to become validated in practice. / Tiivistelmä Ohjelmistoprosessin arvioinnista ja parantamisesta tuli ohjelmistotekniikan keskeinen kiinnostuksen kohde kun Carnegie-Mellon yliopiston ohjelmistotekniikan instituutti SEI julkaisi kypsyysmallinsa ohjelmistoprosessin kyvykkyyden arviointiin vuonna 1987. Siitä lähtien maailmalla on syntynyt lukuisa määrä uusia malleja ja standardeja tälle alueelle. Tässä väitöskirjassa esitellään eurooppalainen ohjelmistoprosessin arviointi- ja parantamismenetelmä BOOTSTRAP, joka kehitettiin alun perin Euroopan unionin ESPRIT tutkimusohjelman rahoittamassa projektissa lähtien japanilaisesta ohut-ajattelusta (Lean) ja sen jatkuvan parantamisen periaatteesta (Kaizen). Esitys keskittyy menetelmän kehittymiseen ja siihen miten menetelmä käytännössä kehitettiin käyttäen kokeellista tutkimustapaa teollisessa ympäristössä. Työ kattaa myös alkuperäiseen menetelmään tehdyt laajennukset, jotka syntyivät yhteistyössä SPICE, PROFES ja TAPISTRY projekteissa tehdyn tutkimuksen tuloksena. Tehdyt laajennukset mahdollistavat menetelmän käytön uusilla sovellusalueilla, takaavat menetelmän yhteensopivuuden alan laatu- ja sertifiointistandardien kanssa, parantavat menetelmän tehokkuutta, laajentavat menetelmän käyttöaluetta prosessin arvioinnista sisältämään myös tuotteen kehittämisen arvioinnin ja vahvistavat parantamisen seurantaa ja tukemista. Toteuttaakseen näiden uusien ominaisuuksien vaatimukset uudet BOOTSTRAP menetelmän julkistukset tarjoavat räätälöityjä ja laajennettuja mallikuvauksia arviointien tekemiseksi sekä entistä täydellisempiä lähestymistapoja arviointien suorittamiselle ja parantamiselle. Menetelmän uudet ominaisuudet mahdollistavat myös usein toistuvien arviointien suorittamisen ja jopa jatkuvan arvioinnin ohjelmisto-mittauksia hyödyntäen. Väitöskirjassa kuvataan yksityiskohtaisesti BOOTSTRAP menetelmän lähtö-kohdat ja ominaisuudet ja se kuinka menetelmä onnistuttiin kehittämään ammattimaiseen ohjelmistoprosessin arviointiin ja parantamiseen sopivaksi. Ensin kuvataan menetelmän kehittyminen ja sitten edetään alan uusien kehitystrendien ja vaatimusten esittelyyn siihen kuinka BOOTSTRAP menetelmä uudet ominaisuudet vastaavat näihin vaatimuksiin. Yhteenvedossa osoitetaan kuinka kehittämisessä onnistuttiin saamaan aikaan uusi menetelmä, joka sopii ammattimaiseen ohjelmistoprosessin arviointiin, vastaa kaikilta osin alan kehittymisen vaatimuksia, sisältää alan standardien vaatimukset täyttävät käytännössä koestetut ominaisuudet, jotka takaavat menetelmän vastaavuuden ISO 15504 standardin vaatimuksiin.

Ce travail de recherche intitulé " Contribution à la modélisation de l'Intégrité des Alimentations dans les System-in-Package", effectué chez NXP semi-conducteurs, se propose d'étudier l'intégrité des alimentations et des signaux dans un système complexe tel que le System-in-Package(SiP), les System-on-Chip(SoC) ou autres (PoP,...). C'est-à-dire la générations de perturbations électromagnétiques conduites dues à l'activité d'un système complexe sur son environnement d'intégration. Un bilan de puissance statique et dynamique permet de considérer l’influence de l’activité des fonctions numériques sur le système SiP. L’activité dynamique est représentée sous forme de profils canoniques caractérisés par la technologie de conception des fonctions logiques. Cette représentation en base tient compte du cadencement multi fréquentiel (ou multi-harmonique) du système. Un logiciel a été développé permettant d'extraire un profil d'activité numérique définit suivant la géométrie de la fonction, sa technologie et ses fréquences d'activation. Les fonctions analogiques et le réseau passif d'interconnexions sont modélisés au travers de fonctions de transfert et validés par une approche expérimentale (domaine fréquentiel et temporel) et en simulation. Cette analyse a permis de souligner les potentialités de la modélisation BBS (Broad Band Spice Model). Ceci a permis une modélisation multi-port globale de l'environnement d'intégration modélisé depuis le PCB jusqu’aux fonctions actives (PCB-Boitier-interconnexions-circuits). Les modèles extraits sont utilisables dans un environnement SPICE où l’ensemble du système est modélisé dans un environnement unique. La CO-MODÉLISATION et la CO-SIMULATION GLOBALES permettent la proposition de règles de conception et l’optimisation du découplage souligné par le potentiel du substrat de report PICS (Passive Integrating Component Substrate). / This thesis, performed in NXP Semiconductors, presents an analysis on POWER INTEGRITY and SIGNAL INTEGRITY in complex systems (System-in-Package SiP, System-on-Chip SoC, PoP, etc). This subject takes in account the propagation and its effects of conducted electromagnetic interferences due to digital activities in power distribution network. A statement of static and dynamic power consumption allows to consider effects of digital activities through a multi-clock and multi harmonic model based on technologies, clocks and geometries of a dedicated functions, blocks or dices. A global distributed CO-SIMULATION/CO-MODELISATION methodology for concurrent/simultaneous analysis of passif distribution network have been successfully applied to a full complex system. An original "power signature" concept is used to model high speed digital modules temporal and spatial distribution of their power switching activity for analog-mixed-digital co-simulations. Analysis of coupling effects at systems level have been studied through access ports with and without active SiP modules. The measured coupling is validated with predicted simulation results based on electromagnetic simulations and broad band SPICE extractions. Correlations are validated between observed spurs in presence of SiP active modules and the behavioral response (transfer function) of the active die multiport, and multi-port de-embedding analysis. The full model of complex system, available in SPICE environnement, allows to analyse propagation and its effects of conducted electromagnetic interferences on dices, functions and system of the SiP. Thanks to this work, it will possible to supply new design rules and optimize of decoupling capacities values. A dedicated software was elaborated to generate a quick digital activity model easy-to-implement in SPICE environment.

Ce projet de maitrise implique le développement et l’optimisation de deux méthodes utilisant la chromatographie liquide à haute performance couplée à la spectrométrie de masse en tandem (HPLC-MS/MS). L'objectif du premier projet était de séparer le plus rapidement possible, simultanément, 71 médicaments traitant la dysfonction érectile (ED) et 11 ingrédients naturels parfois retrouvés avec ces médicaments dans les échantillons suspectés d’être adultérés ou contrefaits. L'objectif du deuxième projet était de développer une méthode de dépistage permettant l'analyse rapide simultanée de 24 cannabinoïdes synthétiques et naturels pour une grande variété d'échantillons tels que les mélanges à base de plantes, des bâtons d'encens, de sérums et de cannabis. Dans les deux projets, la séparation a été réalisée en moins de 10 min et cela en utilisant une colonne C18 à noyau solide 100 x 2,1 mm avec des particules de 2,6 µm de diamètre couplée à un système MS avec trappe ionique orbitale fonctionnant en électronébulisation positive. En raison du nombre élevé de composés dans les deux méthodes et de l’émergence de nouveaux analogues sur le marché qui pourraient être présents dans les échantillons futurs, une méthode de dépistage LC-MS/MS ciblée/non-ciblée a été développée. Pour les deux projets, les limites de détection étaient sous les ng/mL et la variation de la précision et de l’exactitude étaient inférieures de 10,5%. Le taux de recouvrement à partir des échantillons réels variait entre 92 à 111%. L’innovation des méthodes LC-MS/MS développées au cours des projets est que le spectre de masse obtenu en mode balayage lors de l'acquisition, fournit une masse exacte pour tous les composés détectés et permet l'identification des composés initialement non-ciblés, comme des nouveaux analogues. Cette innovation amène une dimension supplémentaire aux méthodes traditionnellement utilisées, en permettant une analyse à haute résolution sur la masse de composés non-ciblés. / This master’s project involved the development and optimization of two rapid liquid chromatography tandem mass spectrometry (LC-MS/MS) methods. The objective of the first project was to simultaneously separate, as rapidly as possible, 71 erectile dysfunction (ED) treatment drugs and 11 natural ingredients sometimes found alongside ED drugs present in suspected adulterated or counterfeit samples. The objective of the second project was to develop a screening method allowing rapid, simultaneous analysis of 24 synthetic and natural cannabinoids for a wide variety of samples such as herbal smoking mixtures, incense sticks, serums and Cannabis plant material. In both projects, the separations were achieved in ≤ 10 min using 2.6 µm fused-core C18 particles packed into a 100 x 2.1 mm column coupled to an LTQ Orbitrap XL mass spectrometer operated in positive electrospray mode. Because of the very high number of compounds in both methods and the knowledge that future analogues are always immerging on the market that could thus be present in samples, a targeted/untargeted LC-MS/MS screening method was developed. For both projects, detection limits were in the sub ng/mL range and intra- and inter-assay precisions were below 10.5%. Recovery from real samples ranged from 92 to 111%. The innovation of the developed LC-MS/MS methods is that the full scan event in the MS acquisition provides accurate masses for all detected species and thus allows post-analysis identification of initially untargeted compounds, i.e., the immerging analogues. This innovation adds an additional dimension to traditional MS/MS methods, allowing high mass resolution of untargeted compounds.