The thesis research aims to further the study of human-robot interaction (HRI) issues, especially regarding the development of an assistive robot designed to help individuals possessing motor impairments. In particular, individuals with amyotrophic lateral sclerosis (ALS), represent a potential user population that possess an array of motor impairment due to the progressive nature of the disease. Through review of the literature, an initial target for robotic assistance was determined to be object retrieval and delivery tasks to aid with dropped or otherwise unreachable objects, which represent a common and significant difficulty for individuals with limited motor capabilities. This thesis research has been conducted as part of a larger, collaborative project between the Georgia Institute of Technology and Emory University. To this end, we developed and evaluated a semi-autonomous mobile healthcare service robot named EL-E. I conducted four human studies involving patients with ALS with the following objectives: 1) to investigate and better understand the practical, everyday needs and limitations of people with severe motor impairments; 2) to translate these needs into pragmatic tasks or goals to be achieved through an assistive robot and reflect these needs and limitations into the robot's design; 3) to develop practical, usable, and effective interaction mechanisms by which the impaired users can control the robot; and 4) and to evaluate the performance of the robot and improve its usability. I anticipate that the findings from this research will contribute to the ongoing research in the development and evaluation of effective and affordable assistive manipulation robots, which can help to mitigate the difficulties, frustration, and lost independence experienced by individuals with significant motor impairments and improve their quality of life.

Around one percent of the Swedish population is defined as visually impaired and ten percent of them are classified as blind (Funka, n.d.; SRF, 2017a). A study shows that the prevalence of nearsightedness will increase to around half the population in the world in 2050 (Holden et. al., 2016). This suggests an increased need for solutions that work for people with reduced vision, not only for visually impaired but for a large group of the population. The aim of the project is to conceptualize a technological mainstream solution that supports people when shopping for groceries. The focus is on making this solution accessible for people with low vision. The project was planned based on the human-centered design process described by IDEO.org (2015), with an overall process divided into three phases: inspiration, ideation, and implementation. In the first phase, inspiration, a literature review was done, different field studies and other research methods were carried out. The outcome of the phase was three personas, two scenarios, and a design specification. During the second phase, ideation, the project scope was narrowed down – focusing on physical grocery stores (excluding online stores) and on conceptualizing a smartphone application. An ideation workshop was conducted, followed by concept creation, paper prototyping, scenario writing, user evaluations and a final concept selection. In the last phase, implementation, follow up feedback sessions were held and a simulation test of the final concept was held. Visualizations and presentation of the final concept were done. A list of summarized design principles was created, as support for further work on designing the application for low vision users. The final concept is based on a smartphone application that supports the customer through shopping list management, aisle navigation, item selection and item scanning, for a seamless customer experience for both people with full and low vision. The technology that will be utilized is Pricer AB's electronic shelf labels (ESL) with item positioning, customer navigation, and individual flashing light, combined with the grocery store online database with item descriptions and images. Here follows an example of how the interaction could look like for someone with low vision: He always prepares his shopping list before heading to the store, this way he knows the shopping will be easier for him. In the store, he gets all items on the list presented in the correct order of the store, in that way he knows what to search for. When looking for soy sauce from his shopping list he has trouble remembering where the section is, so he checks it up with the navigation. He realizes that it was just around the corner of where he just passed by. Once at the section he is presented with a list of different soy sauces in the application, matching his location, previous purchases and the soy sauce on his shopping list. He can now select the one that he prefers, and a picture of it appears on the screen, simultaneously a flashing green light appears by the item on the shelf, and he can easily and independently find the way right up to the soy sauce he wants. / Ungefär en procent av Sveriges befolkning är synskadade, och tio procent av dem är så pass gravt synskadade att de kan definieras som blinda (Funka, n.d.; SRF, 2017a). Enligt en studie förväntas närsynthet världen över att öka, och under 2050 vara uppe i hälften av jordens befolkning (Holden et. al., 2016). Detta tyder på ett ökat behov av lösningar som fungerar för personer med nedsatt syn, inte bara för synskadade utan för en stor del av befolkningen. Målet med projektet är att undersöka nuläget och behoven för synsvaga personer när de handlar mat, för att sedan kunna utveckla universell teknisk ­lösning som ska fungera som ett stöd när man handlar mat. Projektet planerades utifrån en människocentrerad designprocess beskriven av IDEO.org (2015), som är indelad i tre faser: inspiration, idégenereringen och genomförande. I den första fasen, inspiration, gjordes en litteraturstudie, flera fältstudier genomfördes, samt andra research metoder. Resultatet här var tre personas, två scenarion och en designspecifikation. Under den andra fasen, idégenereringen, ställdes nya avgränsningar upp för projektet – fokuset riktades nu mot den fysiska butiker (avgränsning från e-handeln) och att målet skulle vara att ta fram en smartphone-applikation. En idéworkshop genomfördes, konceptgenerering, skapande av pappersprototyper, scenarion, utvärdering med användare och ett slutligt konceptval. I sista fasen, genomförande, följdes det slutliga konceptet upp med tidigare deltagare och det slutliga konceptet testades i en simulerad studie. Visualisering och presentation av slutkonceptet gjordes. Designprinciper för utveckling av applikationer för synsvaga sammanfattades, för att fungera som stöd för vidare arbete med utveckling av konceptet. Slutkonceptet bygger på en smartphone-applikation som ska fungera som stöd för kunden, från skapandet av inköpslista, navigering i butiken, val och identifiering av varor och slutligen att scanna varan. I sin helhet skapar detta en komplett lösning i mataffären för både seende och synsvaga kunder. Tekniken som ska utnyttjas för konceptet är Pricer AB's elektroniska hyllkantsetikett-system (ESL-system) med positionering, kundnavigering samt en lysdiod på varje enskild etikett, i kombination med butikens online-databas med produktbeskrivningar och bilder på varorna. Här kommer en beskrivning av hur interaktionen med systemet kan gå till för någon som är synsvag: Han förbereder alltid sin inköpslista innan han går till affärer, eftersom han vet att det underlättar för honom. Väl i butiken får han varorna från inköpslistan presenterade i den ordningen de kommer, vilket förenklar letandeprocessen. När han letar efter sojasås som han har på listan har han svårt att komma ihåg var i butiken han hittar den, så han kollar upp det med navigeringsfunktionen. Han inser då att han missade den just bakom hörnet som han gick förbi. Väl framme vid sektionen får han en lista med olika sojasåser presenterade i applikationen, de baseras på hans position i butiken, tidigare köp och vad han har på inköpslistan. Han kan nu välja den han gillar och får då en bild på varan på sin skärm, samtidigt som en grön lampa blinkar precis där varan är placerad på hyllan. Han kan nu enkelt och självständigt plocka varan han vill ha från hyllan.

Denna rapport grundar sig i ett examensarbete inom Teknisk design, högskoleingenjörsexamen (A0014A) för femton högskolepoäng, som utförs i Luleå på Luleå tekniska universitet under vårterminen år 2018. Arbetet utförs med samarbete från företaget Modul, som befinner sig i Kalix och tillverkar över hundra olika produkter i tunnplåt. Målet med projektarbetet är att skapa ett koncept på en bra arbetsmiljö på svetsavdelningen och syftet är att minska fysiska och psykiska belastningar på användarna, samt att förbättra den psykosociala arbetsmiljön samtidigt som det kan skapas ett bättre produktionsflöde och eventuellt öka effektiviteten. I projektet har arbetet utförts i tre varv där projektet har gått igenom olika faser flera gånger för att inte missa information eller problem. För att undersöka kontexten och samla in information om nuläget så gjordes fyra studiebesök, intervjuer med uppdragsgivare och fyra användare, en enkät till uppdragsgivaren och observation på svetsavdelningen. Resultaten av denna kontextundersökning kan summeras till att observationen och intervjuerna med användarna gav information om att användarna har mest problem med ljud (buller), klimat, monotona rörelser och belastningar i rygg, fötter och knän. Sedan var det också brist på ljus i svetsbåset, utrymme, snedbelastningar och stress som skapade problem för användarna. För att kunna skapa koncept gjordes två analyser, där den ena analysen var en riskbedömningsanalys som gav information om vilka aspekter inom arbetsmiljön som var mest besvärligt på de olika arbetsstationerna i svetsavdelningen. Sedan gjordes det en analys av hur stationer, lager och andra platser bör vara nära varandra i en så kallat närhetsanalys för att kunna underlätta skapandet av koncept på layouter. Det skapades även en kravspecifikation för att kunna utvärdera och hjälpa till att utveckla koncept, där de viktade kraven viktades av projektmedlemmen och uppdragsgivaren. Kraven som användes var: fysisk belastning, psykosocial arbetsmiljö, klimat, buller, kostnader, utrymme, närhetsbehov, materialflöde, transporter, säkerhet och potential. Efter konceptframtagningen var det fem olika koncept som gick vidare. Koncept 1 är ett koncept där det endast har flyttats på några arbetsstationer för att främst skapa mer utrymme. Koncept 2 är ett koncept som har ett litet rum för att slipa för att isolera bullret från slipstationen och koncept 3 har också ett rum, men på en annan plats. I koncept 4 är svetsavdelningen flyttad till en annan plats i fabriken och i koncept 5 är svetsavdelningen utbyggd på samma plats som i nuläget. Det slutliga resultatet blev ett kortsiktigt och långsiktigt koncept där båda koncepten har förbättrat arbetsmiljön, exempelvis genom att skapa mer utrymme för arbetsstationerna så att användare inte riskerar att snubbla över närliggande lager runt arbetsstationerna och det långsiktiga konceptet har dessutom förbättrat materialflödet i hela fabriken och inte bara inne i svetsavdelningen. Sedan är de slutliga förbättringsförslagen och rekommendationerna att fortsätta utveckla på de slutliga koncepten, rotera mellan arbetsstationer lite oftare, lägg till en ljuskälla till svetsbåsen, ändra arbetsställningarna genom att använda en anpassad stol vid behov, svetsare ska inte ansvara för att arbeta på flera stationer på samma gång eftersom att det leder till stress och fundera på om produkter behöver slipas eller om det går att minska bullret på slipstationen genom att göra det på ett annat sätt. / This report is based on a bachelor´s degree in Industrial Design Engineering for fifteen credits, conducted in Luleå at Luleå University of Technology during the spring term of 2018. The work is carried out with cooperation from the company Modul, which is located in Kalix and manufactures over 100 different products in thin-sheet metal. The aim of the project is to create a concept for a good work environment in the welding department, with the aim of reducing physical and mental stress on users, but also improving the organizational work environment while creating a better production flow and possibly increasing efficiency. This project has gone in three laps where the project has gone through different phases several times to avoid missing information or problems. In order to examine the context and gather information about the current situation there has been four study visits, interviews with the taskmaster and four users, a survey to the taskmaster and an observation in the welding department. The results of this contextual survey can be summed up by the observation and interviews with users that the users have the most problems with noise, climate, monotonous movements and loadings on the back, feet and the knees. Then there was also a lack of light in the welding box, space, oblique loads and stress that created problems for the users. In order to create concepts, two analyzes were made, where one analysis was a risk assessment analysis that provided information on which aspects of the work environment that were the most difficult at the various workstations in the welding department. Then an analysis was made of how stations, warehouses and other places should be close together in a so-called proximity analysis to facilitate the creation of concepts on layouts. A requirement specification was also created to evaluate and help develop concepts, where the weighted requirements were weighted by the project member and the taskmaster. The requirements used were: physical loadings, psychosocial work environment, climate, noise, costs, space, proximity needs, material flow, transport, safety and potential. Following the conceptualization, there are five different concepts that went on. Concept 1 is a concept where only some workstations have been moved to create more space. Concept 2 is a concept that has a small space to grind where the noise from the grinding station can be isolated and concept 3 also has a room for a grinding station, but in another place. In concept 4, the welding department is moved to another location in the factory and in concept 5 the welding department is expanded in the same location of the factory at present. The final result became a short-term and long-term concept, where both concepts have improved the working environment, for example by creating more space for workstations, so that there is no risk of stumbling over nearby storage places around the workstations, and the long-term concept has also improved material flow throughout the factory and not only inside the welding department. The final improvement proposals and recommendations is to continue to develop on the final concepts, rotate between workstations a little more often, add a light source to the welding arcs and change the work postures by using a custom chair when needed. Welders should not be responsible for working at multiple stations at the same time because it leads to stress and think about if it is needed to grind or if the noise of the grinding station can be reduced by doing it differently.

The aim of this thesis is to show how to design a commercially successful website and what are the possibilities of its succesive promotion. First a user research and analysis of competition is done and on the basis of this a new website is designed and created. After its implementation this site is then supported by several online marketing tools.

Abstract Chronic conditions are the leading cause of death in the world. Major improvements in acute care and diagnostics have created a tendency towards the chronification of formerly terminal conditions, requiring people with these conditions to learn how to self-manage. Mobile technologies hold promise as self-management tools due to their ubiquity and cost-effectiveness. The delivery of health-related services through the use of mobile technologies (mHealth) has grown exponentially in recent years. However, only a fraction of these solutions takes into consideration the views of relevant stakeholders like healthcare professionals or even patients. The use of behavioral change models (BCM) has proven important in developing successful health solutions, yet engaging patients remains a challenge. There is a trend in mHealth solutions called gamification that attempts to use game elements to drive user behavior and increase engagement. As it stands, designers of mHealth solutions for behavioral change in chronic conditions have no clear way of deciding what factors are relevant to consider. This doctoral thesis is framed in Consumer Health Informatics within the field of Medical Informatics and Information Systems. The focus of this work was to discover factors for the design of mHealth solutions for chronic patients; to do so, negotiations between medical knowledge, BCM and gamification were explored through an embedded case study research methodology. The data obtained was thematically analyzed to create the Model for Motivational Mobile-health Design for Chronic conditions (3MD). The 3MD model guides the design of condition-oriented gamified behavioral change mHealth solutions. The main components are: 1) Condition specific, which describe factors that need to be adjusted and adapted for each particular chronic condition; 2) Motivation related, which are factors that address how to influence behaviors in an engaging manner; and 3) Technology based, which are factors that are directly connected to the technical capabilities of mobile technologies. 3MD also provides a series of high level illustrative design questions for designers to use and consider during the design process. The work on this thesis addresses a recognized gap in research and practice, and proposes a unique model that could be of use in the generation of new solutions to help chronic patients. / Tiivistelmä Krooniset sairaudet ovat maailman yleisin kuolinsyy. Akuutissa hoidossa ja diagnostiikassa on tapahtunut merkittäviä parannuksia, ja aikaisemmin kuolemaan johtaneista sairauksista on tullut kroonisia ja ihmisten on opittava hallitsemaan niitä itse. Mobiiliteknologiat tarjoavat mahdollisuuksia sairauksien itsehallintaan, koska teknologiaa on yleisesti saatavilla ja se on kustannustehokasta. Terveyspalvelujen tarjoaminen mobiiliteknologian avulla on lisääntynyt huomattavasti viime vuosina. Kuitenkin vain murto-osa näistä ratkaisuista ottaa huomioon sidosryhmien, kuten terveydenhuollon ammattilaisten ja jopa potilaiden, näkemykset. Käyttäytymismuutosmallit ovat osoittautuneet tärkeiksi kehitettäessä onnistuneita terveysratkaisuja, mutta potilaiden osallistaminen kehittämiseen on yhä vaikeaa. Pelillistäminen on mobiilien terveysratkaisujen suunnittelutrendi, ja pelielementeillä pyritään vaikuttamaan ihmisten käyttäytymiseen ja sitoutumiseen. Mobiilien terveyssovellusten suunnittelijoilla ei ole selkeää näkemystä siitä, mitkä sovellustekijät vaikuttavat merkittävimmin kroonisissa sairauksissa sairastavien potilaiden käyttäytymisen muutokseen. Tämä väitöskirja tarkastelee kuluttajille suunnattua terveysteknologiaa, joka hyödyntää lääketieteellistä informatiikkaa ja tietojärjestelmätieteitä. Työn tavoitteena oli selvittää kroonisia sairauksia sairastaville potilaille tarkoitettujen mobiilien terveyssovellusten suunnitteluun liittyviä tekijöitä. Tämän vuoksi lääketieteen tietämyksen, käyttäytymismuutoksien mallien ja pelillistämisen yhdistämistä tutkittiin sulautetun tapaustutkimuksen avulla. Saatuja tietoja temaattisesti analysoimalla luotiin kroonisia sairauksia varten motivoivan mobiilin terveyssovelluksen suunnittelumalli (3MD = Model for Motivational Mobile-health Design). 3MD-malli ohjaa sairauksien hallintaan tarkoitettujen pelillistettyjen ja käyttäytymismuutoksiin tähtäävien mobiilien terveyssovellusten suunnittelua. Mallin pääkomponentit ovat: 1) Sairautta kuvaavat tekijät, jotka kuvaavat tekijöitä, jotka on mukautettava ja sovitettava kullekin krooniselle sairaudelle. 2) Motivaatioon liittyvät tekijät, jotka vaikuttavat innostavasti käyttäytymiseen. 3) Teknologiaan perustuvat tekijät, jotka liittyvät suoraan mobiiliteknologian teknisiin ominaisuuksiin. 3MD tarjoaa myös havainnollisia suunnittelukysymyksiä, joita suunnittelijat voivat käyttää ja pohtia suunnitteluprosessin aikana. Tämä väitöskirja käsittelee yleisesti tunnistettua puutetta tutkimuksessa ja suunnittelukäytännössä ja esittelee ainutlaatuisen mallin, josta voi olla hyötyä uusien ratkaisujen luomisessa ja kroonisia sairauksia sairastavien potilaiden auttamisessa.

Cette thèse porte sur la Conception Centrée Valeur (CCV) proposé par Gilbert Cockton dans le but d'aller au-delà de l'utilisabilité dans les systèmes interactifs. L'auteur propose un canevas pour la mise en oeuvre de la CCV. Cependant, les opérationnalisations restent partielles et sont réalisées par lui-même, d'où un manque de recul de la communauté vis-à-vis de la méthode. La thèse relate la conception centrée valeur de Cocoon, un système d'information mobile et sensible au contexte. Elle apporte des contributions à la fois sur les plans conceptuel et méthodologique. D'un point de vue conceptuel, elle introduit la taxonomie PIPE (Personnelle, Impersonnelle, Pérenne, Éphémère) pour la caractérisation de l'information. En outre, elle montre que les systèmes existants ne couvrent pas PIPE : ils sont surtout focalisés sur les informations impersonnelles. Alors, la thèse propose le concept d'arbre de vie et Cocoon. D'un point de vue méthodologique, la thèse apporte une compréhension meilleure de la notion de valeur. En outre, elle fournit un retour d'expérience sur la CCV accompagné de remarques et recommandations pour des mises en oeuvres futures plus performantes. Enfin, elle propose un canevas pour la construction des cartes de valeur et une stratégie pour l'estimation de la valeur. / The thesis deals with Worth Centered Design (WCD) introduced by Gilbert Cockton. The author also introduced a framework aimed to support the WCD operationalization. However, this framework has been operationalized only partially until now and by Gilbert Cockton himself. The thesis relates our WCD experience with Cocoon, a mobile and context-aware information system. The thesis contributions are both conceptual and methodological. From a conceptual point of view, we introduce the PIPE (Personal, Impersonal, Perennial, Ephemeral) taxonomy for information characterization and show that existing systems only partially covers the PIPE information space: they focus on impersonal information. This notice motivated us to propose the life tree concept and Cocoon. From a methodological point of view, we offer a feedback to the community on an interesting concept method as well as recommendations for more efficient operationalizations. In addition, we introduce a framework for worth maps construction and a strategy for worth assessment.

Att blanda matrester med vanligt hushållsavfall har negativ inverkan på miljön. Men trots detta visar den senaste statistiken att enbart 25,5 % av matavfallet från svenska hushåll sorteras ut. Det verkar bland annat bero på en negativ inställning, och kan indikera ett behov av information som övertygar om vikten att sortera ut. Därför efterfrågade Eskilstuna Strängnäs Energi & Miljö ett material som motiverar boende till en ändrad attityd. Studiens syfte var att komma fram till hur information om att sortera ut matavfall kan utformas för att positivt påverka mottagarnas inställning. Arbetet utgick från teori inom retorik, budskapsstrategier och användarcentrerad design, vilket tillsammans med empirisk data blev grunden för ett gestaltningsförslag. Empirisk data samlades in genom fyra metoder: en intervju med en ämnesexpert för att rama in problemet, en retorisk textanalys för att resonera kring om befintlig information bidragit till att problemet kvarstår, en enkätundersökning för att definiera målgruppens informationsbehov, attityd och mediepreferens samt två utvärderande tester för att undersöka om gestaltningsförslaget fick avsedd inverkan. Genom detta kunde flera slutsatser dras. Bland annat att en blandad budskapsstrategi, metaforer, bilder och att tilltala läsaren som ”du” kan ha positiv inverkan på mottagarens inställning, utifrån vilka en slutgestaltning skapades. / The environment is impacted in a negative way when food waste is commingled with other waste from the household. Still, the latest statistics show that only 25,5 % of the food waste from Swedish households is sorted out. This seems to be caused by a negative attitude among other things, and can indicate a need for convincing information about the importance of sorting out. Therefor, Eskilstuna Strängnäs Energi & Miljö requested a material meant to motivate residents to change their attitude. The study’s purpose was to find out how information about sorting out food waste can be formed to make a positive impact on the receiver’s attitude. The study emanated from theories within rhetoric, message strategies and human centered design, which along with empirical data became the foundation for a design proposal. Empirical data was collected through four methods: an interview with a expert within the subject to frame the problem, a rhetorical text analysis to discuss if existing information have contributed to that the problem still remain, a questionnaire survey to define the target group’s information need, attitude and preferred medium, and two evaluative tests to examine if the design proposal had the intended impact. Through this, multiple conclusions could be drawn. For instance that a combined message strategy, metaphors, images and addressing the reader as “you” can have a positive impact on the receiver’s attitude, by which a final design was created.

Submitted by Alison Vanceto (alison-vanceto@hotmail.com) on 2017-04-19T14:31:07Z No. of bitstreams: 1 TeseACMO.pdf: 3842026 bytes, checksum: 7081c677ee2f15ff2fd1eb1c4a5281da (MD5) / Approved for entry into archive by Ronildo Prado (ronisp@ufscar.br) on 2017-04-27T14:02:11Z (GMT) No. of bitstreams: 1 TeseACMO.pdf: 3842026 bytes, checksum: 7081c677ee2f15ff2fd1eb1c4a5281da (MD5) / Approved for entry into archive by Ronildo Prado (ronisp@ufscar.br) on 2017-04-27T14:02:30Z (GMT) No. of bitstreams: 1 TeseACMO.pdf: 3842026 bytes, checksum: 7081c677ee2f15ff2fd1eb1c4a5281da (MD5) / Made available in DSpace on 2017-04-27T18:11:36Z (GMT). No. of bitstreams: 1 TeseACMO.pdf: 3842026 bytes, checksum: 7081c677ee2f15ff2fd1eb1c4a5281da (MD5) Previous issue date: 2016-12-13 / Não recebi financiamento / Situation Awareness (SAW) is a cognitive process defined as the perception of elements and events within a time frame, the understanding of their situation and the projection of their status. SAW is a prerequisite for decision-making in dynamic and complex systems and errors in SAW are an acknowledged source of human errors and accidents. Its study is pivotal in many industries, such as aviation, military, oil, gas and rails, and it is being increasingly considered for maintenance, since this activity is deemed critical for every industry. New technologies to support maintenance, such as E-Maintenance, will provide easier access to the desired information to technicians, but the way new technologies lead to improved SAW is influenced by how information is presented in the User Interface (UI), and many UIs for maintenance technicians support their decision-making regarding procedural and technical criteria, but not economical, legal, ethical and political. Therefore, they only allow a partial development of the user SAW, but not the complete comprehension and projection of a situation. These UIs ignore information requirements such as: risks and conditions of the environment; automations; actions and decisions of team members; rules, regulations and policies of enterprises. Therefore, the design and development of UIs to improve SAW in maintenance is compromised by the few solutions in the state of the art for SAW supportive UI design, for model-based design process and for frameworks and reference architectures. Cognizant to this gap, this thesis proposes a solution for the design and development of Situation Awareness support User Interfaces (SASUI) for maintenance work. For that three contributions are proposed: a conceptual framework of Situation Awareness Aspects (FSA) that assists developers in structuring heterogeneous sources of data into a knowledge representation model, to obtain a state oriented view of SAW; a multiagent architecture that instantiates and controls UIs to improve their support of SAW, by using a blend of SAW and UI agents to express the situation (and its projection) of real world entities in the UI; a methodology to create Model-based SAW User Interfaces (MBSAW-UI), in which designers model agents that will assist users in acquiring the SAW necessary for their decision-making process. These contributions follow a Cognitive Engineering approach to guide software developers in the UI design process and also empower domain experts to model their UIs, enabling an End-User Development (EUD) paradigm that facilitate future updates to the system. A study case of a maintenance activity was developed to evaluate these solutions, with two interfaces: a UI designed using MBSAW-UI; a UI designed using solely a Hierarchical Task Analysis. An experiment was performed and showed a 78% increase in SAW with the UI designed to support SAW, which lead to enhanced efficacy (3,85x less errors) and safety (3,87x less errors regarding unsafe behavior). / Consciência Situacional (SAW) é um processo cognitivo definido como a percepção de elementos e eventos em um volume de tempo e espaço, o entendimento da situação atual e a projeção do seu estado futuro. SAW é um pré-requisito para a tomada de decisão em sistemas complexos e dinâmicos, e os problemas em SAW são uma fonte reconhecida de erros humanos e acidentes. O estudo de SAW não só é fundamental em muitos setores (como, por exemplo, aviação, forças armadas, óleo, gás e ferrovias), como vem sendo considerado, de forma crescente, em áreas como a manutenção, que é uma atividade crítica para todas as indústrias. Novas tecnologias para apoio a manutenção, como a E-Manutenção, vão prover melhor acesso a informações desejadas, porém a SAW de um trabalhador que lida com tecnologia está correlacionada a Interface do Usuário (IU) do sistema, e diversas IUs para manutenção apoiam a tomada de decisão considerando critérios procedurais e técnicos, mas não econômicos, legais, éticos e políticos. Portanto elas somente apoiam um desenvolvimento parcial da SAW de seu usuário, mas não a completa compreensão e projeção da situação. Estas interfaces ignoram requisitos de informação como: riscos e condições do ambiente; automações; ações e decisões de colegas de equipe; regras, regulamentos e políticas das empresas. Dessa forma, o design e desenvolvimento de IUs para aprimorar a SAW na manutenção são comprometidos pelas poucas soluções no estado da arte de design de IU para apoio a SAW, de processos de design baseado em modelos e de frameworks e arquiteturas de referência. Ciente desta lacuna, esta tese propõe uma solução para design e desenvolvimento de Interfaces do Usuário que apoiam o estabelecimento de SAW (SASUI) em trabalhos de manutenção. Três contribuições foram geradas: um framework conceitual de aspectos de SAW (FSA) que auxilia desenvolvedores a estruturar fontes de dados heterogêneas em um modelo de representação do conhecimento, para obter uma visão de SAW orientada a estado; uma arquitetura multiagente que instancia e controla IUs para aprimorar o apoio a SAW, usando uma combinação de agentes de SAW e IU que expressam a situação (e projeção) de entidades do mundo real; e, finalmente, uma metodologia para criar IUs para SAW baseada em modelos (MBSAW-UI), na qual designers modelam agentes que irão auxiliar usuários a adquirir a SAW necessária para seu processo de tomada de decisão. Estas contribuições seguem uma abordagem de Engenharia Cognitiva para guiar desenvolvedores de software no processo de design de IU e para permitir especialistas de domínio a modelar suas IUs, habilitando um paradigma de End-User Development (EUD) que facilita futuras atualizações ao sistema. Foi desenvolvido um estudo de caso de uma atividade de manutenção para avaliar as soluções propostas, usando duas interfaces: uma projetada usando a metodologia MBSAWUI; e outra usando somente análise hierárquica de tarefas. Experimentos realizados mostram que as interfaces geradas com a metodologia proposta neste trabalho proporcionaram um aumento de 78% na SAW, o que levou a uma melhor eficácia (3,85x menos erros) e segurança (3,87x menos erros relacionados a comportamentos arriscados).

Datalager används för att ge företag en samlad bild av sin verksamhet, en bild som byggs upp av analytikers statistiska beräkningar och modeller. Analytiker arbetar i datalager med hjälp av olika analysverktyg, och begränsas av dessa verktygs möjligheter att ge en förståelse av datalagrets uppbyggnad och funktion, och av möjligheterna att hitta rätt analysdata. Arbetet med att hitta och analysera data är en iterativ problemlösningsprocess för att få fram det önskade resultatet. Visualiseringar kan fungera som ett verktyg i arbetet och stödja användares beslutsfattande. Denna kvalitativa fallstudie syftar till att undersöka hur visualisering kan användas som ett stöd för marknads- och kreditanalytikers datalagerarbete. Studien använde användarcentrerade metoder för att undersöka analytikers arbete i ett datalager. Femton kunskapsuppgifter identifierades som mål för visualiseringsstöd i analytikers datalagerarbete. Ett analysorienterat och ett systemorienterat strukturförslag för visualiseringar värderades med dessa kunskapsuppgifter som viktade mål. Av kunskapsuppgifterna är den viktigaste att koppla analysuppgifter till systemstruktur. Det kräver att visualiseringsstödet erbjuder en analysorienterad struktur initialt och blir alltmer systemorienterat i takt med att den intressanta informationsmängden definieras. Användarcentrerade metoder användes för att identifiera kunskapsuppgifter. Studien visar att dessa kunskapsuppgifter kan användas som designmål för värdering av visualiseringsstöd.

A literatura de design e de arquitetura sugere a necessidade de realização de estudos mais aprofundados e capilares junto a usuários de baixa renda a respeito da realidade material interior de suas residências, de como se daria a efetiva utilização de bens e objetos pessoais, além de suas aspirações e preferências quanto aos produtos de uso doméstico. Vários autores, neste sentido, ressaltam que a produção brasileira de mobiliário residencial industrializado, também denominado móvel seriado, sobretudo no segmento do consumo popular, não atenderia, integralmente, a seu público principal, concentrado nestas duas faixas socioeconômicas da população. Este alegado descompasso existiria, parcialmente, em razão de designers e fabricantes de móveis populares seriados supostamente desconhecerem as necessidades efetivas dos usuários e as maneiras de interação com seus bens domésticos. Nesta pesquisa, foram investigadas várias situações de uso do referido mobiliário popular industrializado em moradias de usuários selecionados residentes na Grande São Paulo, abordando aspectos tais como: percepções, significados, preferências, avaliações, apropriações, formas de utilização e adequação aos ambientes. Em termos metodológicos, este estudo qualitativo, de caráter essencialmente fenomenológico, mas também observacional, foi constituído pela sistematização e análise associativa de dados obtidos por meio de entrevistas em profundidade semiestruturadas conduzidas com quarenta usuários e doze vendedores. O trabalho de campo foi complementado por observações diretas, produzidas pela pesquisadora, de móveis, objetos e demais arranjos físicos e visuais encontrados nas moradias visitadas e em lojas de móveis populares, com auxílio de registros fotográficos e gravações em áudio. Na análise do conjunto de dados coletados, foram identificados elementos semióticos, estéticos, funcionais, socioculturais e psicológicos, entre outros. Os resultados obtidos permitem iluminar questões efetivas de uso do mobiliário popular, além de hábitos, costumes, preferências estéticas e condições internas das moradias dos usuários participantes. Observou-se, por exemplo, neste sentido, reduzida adequação de parcela significativa do mobiliário às habitações visitadas, bem como presença de improvisações e adaptações a que os usuários comumente recorrem, mesmo em móveis com pouco tempo de aquisição, para que voltem a desempenhar adequadamente suas funções, além de certa resignação de parte dos usuários quanto a deficiências de projeto e de produção verificadas nos móveis, por vezes justificadas, por eles, pelos baixos preços que pagaram. Tais percepções e outros achados disponibilizam, assim, um corpo de insumos para designers e indústria moveleira em geral, sobre necessidades específicas de famílias de baixa renda que encontram, neste mobiliário popular industrializado, sua principal ou única, mesmo que, em casos, precária, opção de compra para atendimento de necessidades básicas de armazenamento de objetos pessoais e de apoio a tarefas domésticas. Espera-se, com esta pesquisa, contribuir para que o projeto e a produção desta classe de produtos ofereça maior adequação ao efetivo modo de vida e necessidades de seus usuários no interior de suas moradias. / The design and architecture literature suggests the need for more in-depth studies with low-income users regarding the material in their homes and how belongings and personal objects would actually be used, as well as what their aspirations and preferences are with regard to domestic products. Several authors in this context emphasize that Brazilian industrial residential furniture production, also called furniture in series, especially in the budget furniture segment, does not entirely meet the needs of its main public, concentrated in these two socio-economic groups. This alleged misalignment would exist partially because of designers and manufacturers of low-cost furniture supposedly being unaware of users\' real needs and ways of interacting with their domestic objects. In this research, several ways of using industrial low-cost furniture in selected users\' homes in Greater São Paulo were investigated, looking at aspects such as: perceptions, meanings, preferences, evaluations, appropriations, forms of use and adequacy of the environments. In methodological terms, this essentially phenomenological, but also observational qualitative study was done by the systematization and associative analysis of data obtained through in-depth, semi-structured interviews with forty users and twelve salespeople. The field work was complemented by the researcher\'s direct observation of furniture, objects and other physical and visual arrangements in the homes visited and in budget furniture stores, and also with the aid of photographs and audio recordings. In the analysis of the collected data set, semiotic, aesthetic, functional, sociocultural and psychological elements were identified, among others. The results obtained provide information about the use of low-cost furniture, and also about habits, customs, aesthetic preferences and internal conditions of the participating users\' homes. It was observed, for example, that much of the furniture in the homes visited was of limited adequacy, and there were often user improvisations and adaptations, even in furniture purchased recently, so that it would more adequately fulfill its function. In addition, the users had a certain feeling of resignation about the furniture\'s design and manufacturing deficiencies, sometimes justified, for them, by the low price they had paid. These perceptions and other findings make available, then, input for designers and the furniture industry, in general, on specific needs of low-income families that have, in this industrialized low-cost furniture, their main or only, though sometimes precarious, purchase option to meet their basic needs for storage of their belongings and support for domestic tasks. It is hoped that this research will contribute to the design and production of this class of products becoming more suited to the lifestyles and needs of users in their homes.