Global ETD Search

221	Dvoutlaký horizontální kotel na odpadní teplo (HRSG) / Heat Recovery Steam Generator with Two Pressure Levels Maršík, Jaroslav January 2015 (has links) The Master’s thesis dealing with design of heat recovery steam generator with two pressure levels is split into nine sections. The first section describes the design and the layout of HRSG. The second part deals with heat calculation. The third section deals with design of flue-gas duct. The fourth part describes designs of individual heating surfaces, including steam superheaters, vaporizers and economizer. Next section shows the real temperature diagram and choice of the materials. The seventh section describes the calculation of outer pipelines and the eighth part deals with the drums design. The last section deals with the calculation of draft loss of steam generator.
222	Návrh dvoutlakého horizontálního kotle na odpadní teplo / Proposal two-pressures horizontal waste heat boiler Med, Lukáš January 2016 (has links) This master's thesis deals with thermal calculation and design of proportions of calorific components of a heat recovery steam generator (HRSG), which is placed behind a combustion turbine, for given parameters of exhaust gases and requested parameters of steam. In the first chapters is described the design, layout of HRSG and the thermal calculation. The next parts deal with the design of flue-gas duct and each individual heating surface. Next section shows computations of dimensions of drums, flooding pipes, transferring pipes and all other outer pipes. The chosen materials are described in one of the last chapters and the last chapter deals with calculation of draft loss of steam generator.
223	Caractérisation expérimentale et numérique du comportement rhéologique d'un fluide complexe : application à une mousse en écoulement dans un canal horizontal droit avec et sans singularités / Experimental and numerical characterization of the rheological behavior of a complex fluid : application to a wet foam flow through a horizontal straight duct with and without flow disruption devices (FDD) Chovet, Rogelio 17 July 2015 (has links) Ce travail porte sur l’étude expérimentale et numérique de l’écoulement des mousses humides dans un canal horizontal droit de section carrée avec ou sans singularités. Il est consacré tout particulièrement à déterminer les paramètres pertinents de l’écoulement dont la chute de pression longitudinale, les champs de vitesse de l’écoulement de mousse en proche parois, les épaisseurs de films liquides minces et épais en paroi et l’évolution de la contrainte pariétale pour une mousse humide dont la fraction gazeuse varie de 55 à 85% et la vitesse débitante de la mousse est 2, 4 puis 6 cm/s. Une fois ces paramètres déterminés en conduite horizontale droite, nous avons ensuite effectué des mesures sur différentes géométries représentant un élargissement brusque, une chicane verticale et écoulement de mousse autour d’un cylindre, dont le but est d’étudier la réorganisation de l’écoulement en vue de déterminer le comportement rhéologique des mousses en écoulement à l’aval et à l’amont des singularités. Finalement, une étude de simulation numérique (CFD) en utilisant les lois de comportement de type Bingham, pour fluides non newtoniens, a été effectuée afin de tester sa capacité de représenter des écoulements type mousse humide dans une conduite horizontale avec ou sans singularités. Nous avons vérifié tout d’abord l’évolution longitudinale de la pression statique qui est linéaire à l’amont comme à l’aval loin des zones influencées par les singularités. La chute de pression singulière reste à peu près constante pour une vitesse débitante donnée de la mousse. À partir de la technique de Vélocimétrie par Image de Particule (PIV), nous avons déterminé les composantes de vitesse au voisinage immédiat des singularités. Ces mesures nous ont permis de mettre en évidence l’existence de différents régimes d’écoulement, et de déterminer la réorganisation et le comportement rhéologique de l’écoulement de mousse autour des géométries étudiées. L’analyse des mesures d’épaisseur de films liquides, obtenues par la méthode conductimétrique, indique que la paroi reste mouillée par un film liquide suffisamment épais pour qu’on puisse appliquer la méthode électrochimique. Les signaux polarographiques obtenus avec la mousse présentent alors de fortes fluctuations. La comparaison de celles-ci avec les contraintes pariétales déduites à partir des mesures de la chute de pression montre bien une bonne concordance. L’étude numérique (CFD), effectuée pour une fraction volumique de gaz égale à 70% et qui s’écoule avec une vitesse débitante de 2 cm/s, montre que le modèle rhéologique de Bingham pourrait être bien adapté à ce genre de mousse humide évoluant en écoulement en bloc. / This work is an experimental and numerical study of aqueous foam flow inside a horizontal square duct, with and without flow disruption devices (fdd). It is especially devoted to determine the pertinent parameters of the flow: longitudinal pressure losses, velocity fields of foam flow near the walls, liquid film thickness (thick and thin), and the wall shear stress evolution, for an aqueous foam with a void fraction range between 55 and 85%, for a mean foam flow velocity of 2, 4 and 6 cm/s. Once they were determined, inside the horizontal channel, we carried out measurements over different geometries: half-sudden expansion, vertical fence and foam flow around a cylinder. The goal was to study the foam flow reorganization to well understand the rheological behavior of aqueous foam flow in the vicinities of different fdd. Finally, a numerical simulation (CFD), using the Bingham behavior model of non-Newtonian fluid, was undertaken to test its capacity to represent the aqueous foam flow inside the horizontal duct with flow disruption devices. First of all, we verified the static longitudinal pressure evolution, which varies linearly upstream and downstream far from the fdd. The singular pressure loss remains constant for a given mean foam velocity and a foam quality (void fraction). From the Particle Imaging Velocimetry (PIV) technique (2D), we determined the two velocity components in the immediate vicinities of the disruption devices. They allowed us to put into evidence the different foam flow regimes and to observe the foam flow reorganization and rheological behavior through the studied fdd. The slip-layer thickness analysis, obtained using the conductimetry method, shows that the wall presents a liquid film thick enough to apply an electrochemical technique (polarography). Thus, the polarographic signals, obtained for the foam flow, present important fluctuations. They were compared to the wall shear stress deducted from the measurement of pressure losses, showing a good similarity between them. The numerical study (CFD), carried out for aqueous foam flow with a void fraction of 70% and a mean foam flow velocity of 2 cm/s, shows that the Bingham rheological model can be adapted to this kind of aqueous foam flow which is flowing like a block. Mousse humide Écoulement Rhéologie Conduite horizontale Section carrée Singularités Méthode polarographique Contrainte pariétale Méthode conductimétrique Film liquide Taux de vide Cfd Modèle de Bingham. Aqueous foam Flow Rheology Horizontal duct Square section Flow disruption devices Particle Imaging Velocimetry (PIV) Polarographic method Wall shear stress Conductimetric method Liquid-Slip layer Void fraction Cfd Bingham model.
224	THE ROLE OF ENERGY DISSIPATION, SUPERELASTICITY, AND SHAPE MEMORY EFFECTS IN ARCHITECTED MATERIALS FOR ENGINEERING APPLICATIONS Kristiaan Hector (13892400) 13 October 2022 (has links) <p>The main goal of this thesis research is to expand the range of unique properties of phase transforming cellular materials (PXCMs), a new class of architected materials, and to extend their applicability both in the engineering disciplines and in the medical field. A novel aspect of PXCMs is their unique energy dissipation during loading via a snapping mechanism associated with a geometric transition between one stable configuration to another stable configuration at the unit cell level. Phase transformation is analogous to displacive transformations, such as martensitic transformations in shape memory alloys, with no change in configurational entropy. To accomplish this goal, three problem areas are addressed with the first exploring the effects of length scale as added structural hierarchy on material properties and energy dissipation, the second providing an analysis of the durability of architected materials via a novel additive manufacturing method, and the third, an extension into the medical field. Two examples are provided that demonstrate the effects of length scale as added structural hierarchy on material properties, and a machine learning approach for the feasible design of materials with additional levels of structural hierarchy is presented. A simple design approach coupled with a novel additive manufacturing method is discussed for the design of architected materials with high durability. Lastly, a concept for de-clogging bile stents via a temperature driven, shape-memory mechanism inspired by peristaltic locomotion in the human esophagus is presented.</p> Architectural engineering Structural engineering architected materials cellular materials PXCM ASMA phase transforming cellular materials artificial shape memory analogs stents bile duct cancer peristalsis snap through sinusoidal beams tape spring ligaments octets fatigue chiral PXCM energy dissipation super elasticity shape memory effect machine learning smart material design inverse design genetic algorithms
225	DESIGN METHODS FOR LARGE RECTANGULAR INDUSTRIAL DUCTS Thanga, Tharani 10 1900 (has links) <p>A large rectangular industrial duct consists of plates stiffened with parallel wide flange sections. The plates along with stiffeners acts to resist the pressure loads and to carry other loads to the supports. The behaviours of the components of large industrial ducts are significantly different from the behaviours on which the current design methods are based on. Investigation presented herein deals with the design methods for spacing stiffeners, proportioning stiffeners and calculating shear resistance of side panel.</p> <p>Current method of spacing stiffeners is based on large deflection plate theory. A parametric study was conducted on dimensionless parameters identified in order to benefit from membrane action in partially yielding plate for spacing stiffeners. Design equations were established in terms of dimensionless pressure, plate slenderness and normalized out-of-plane deflection for three cases namely; 0%, 16.5% and 33% of through thickness yielding of the plate. Results show that approximately 50% increase in stiffener spacing when yielding of 16.5% of thickness is permitted.</p> <p>Under suction type pressure load, the unsupported compression flange and restrained tension flange lead to distortional buckling of the stiffeners. The current methods do not address distortional buckling adequately. A parametric study on dimensionless parameters governing the behaviour and strength of stiffened plat panels was conducted. The study indicated that the behaviour and strength of the stiffened panels could be a function of web slenderness and overall slenderness of the stiffener. The study also identified the slenderness limit of stiffener web for which the stiffener reaches the yield moment capacity. This study demonstrated the conservatism of current method. Finally a method was established to calculate the strength of stiffened plate panel subjected lateral pressure.</p> <p>Side panels adjacent to the supports transfer large amount of shear to the supports and, in addition, resist internal pressure. Currently the design of side panels for shear is based on the methods used for the web of fabricated plate girders. The behaviour and the characteristics between the web of plate girder and the thin side panels are significantly different. A parametric study was conducted on dimensionless parameters identified. It was concluded that the plate slenderness dominates the normalized shear strength of stockier side panels. The aspect ratio and plate slenderness influence the normalized shear strength of slender side panels. Design methods to calculate the shear strength of side panels were proposed.</p> / Doctor of Philosophy (PhD) Large Rectangular industrial duct Stiffened plate panel Finite element model Parametric study Large deflection plate theory Partial yielding Stiffener spacing Plate thickness Initial Imperfection Residual Stress Plate buckling Overall buckling Distortional Buckling Shear Buckling Normalized ultimate Shear Diagonal Tension Field Dimensional Analysis Dimensionless parameters Structural Engineering Structural Engineering
226	Högtempererat borrhålslager för fjärrvärme / High Temperature Borehole Thermal Energy Storage for District Heating Hallqvist, Karl January 2014 (has links) The district heating load is seasonally dependent, with a low load during periods of high ambient temperature. Thermal energy storage (TES) has the potential to shift heating loads from winter to summer, thus reducing cost and environmental impact of District Heat production. In this study, a concept of high temperature borehole thermal energy storage (HT-BTES) together with a pellet heating plant for temperature boost, is presented and evaluated by its technical limitations, its ability to supply heat, its function within the district heating system, as well as its environmental impact and economic viability in Gothenburg, Sweden, a city with access to high quantities of waste heat. The concept has proven potentially environmentally friendly and potentially profitable if its design is balanced to achieve a good enough supply temperature from the HT-BTES. The size of the heat storage, the distance between boreholes and low borehole thermal resistance are key parameters to achieve high temperature. Profitability increases if a location with lower temperature demand, as well as risk of future shortage of supply, can be met. Feasibility also increases if existing pellet heating plant and district heating connection can be used and if lower rate of return on investment can be accepted. Access to HT-BTES in the district heating network enables greater flexibility and availability of production of District Heating, thereby facilitating readjustments to different strategies and policies. However, concerns for the durability of feasible borehole heat exchangers (BHE) exist in high temperature application. / Värmebehovet är starkt säsongsberoende, med låg last under perioder av högre omgivningstemperatur och hög last under perioder av lägre omgivningstemperaturer. I Göteborg finns en stor mängd spillvärme tillgängligt för fjärrvärmeproduktion sommartid när behovet av värme är lågt. Tillgång till säsongsvärmelager möjliggör att fjärrvärmeproduktion flyttas från vinterhalvår till sommarhalvår, vilket kan ge såväl lönsamhet som miljönytta. Borrhålsvärmelager är ett förhållandevis billigt sätt att lagra värme, och innebär att berggrunden värms upp under sommaren genom att varmt vatten flödar i borrhål, för att under vinterhalvåret användas genom att låta kallt vatten flöda i borrhålen och värmas upp. I traditionella borrhålsvärmelager används ofta värmepump för att höja värmelagrets urladdade temperatur, men på grund av höga temperaturkrav för fjärrvärme kan kostnaden för värmepump bli hög. I denna rapport föreslås ett system för att klara av att nå höga temperaturer till en lägre kostnad. Systemet består av ett borrhålsvärmelager anpassat för högre temperaturer (HT-BTES) samt pelletspannor för att spetsa lagrets utgående fluid för att nå hög temperatur. Syftet med rapporten är att undersöka potentialen för detta HT-BTES-system med avseende på dess tekniska begränsningar, förmåga till fjärrvärmeleverans, konsekvenser för fjärrvärmesystemet, samt lönsamhet och miljöpåverkan. För att garantera att inlagringen av värme inte är så stor att priset för inlagrad värme ökar väsentligt, utgår inlagringen från hur mycket värme som kyls bort i fjärrvärmenätet sommartid. I verkligheten finns betydligt mer värme tillgänglig till låg kostnad. När HT-BTES-systemet producerar fjärrvärme, ersätts fjärrvärmeproduktion från andra produktionsenheter, förutsatt att HT-BTES-systemets rörliga kostnader är lägre. I Göteborg ersätts främst naturgas från kraftvärme, men också en del flis. Kostnadsbesparingen beror på differensen för total fjärrvärmeproduktionskostnad med och utan HT-BTES-systemet. Undersökningen visar att besparingen är större om HT-BTES-systemet placeras i ett område där det är möjligt att mata ut fjärrvärme med lägre temperatur. Om urladdning från HT-BTES kan ske med hög temperatur ökar också besparingen. Detta sker om lagrets volym ökar, om avståndet mellan borrhål minskar eller om värmeöverföringen mellan det flödande vattnet i borrhålen och berggrunden ökar. Dessa egenskaper för lagret leder också till minskade koldioxidutsläpp. Storleken på besparingen beror dock i hög grad på hur bränslepriser utvecklas i framtiden. Strategiska fördelar med HT-BTES-systemet inkluderar; minskad miljöpåverkan, robust system med lång teknisk livslängd (för delar av HT-BTES-systemet), samt att inlagring av värme kan ske från många olika produktionsenheter. Dessutom kan positiva bieffekter identifieras. Undersökningen visar att HT-BTES-systemet har god potential att ge lönsamhet och minskad miljöpåverkan, och att anläggning och drift av lagret kan ske utan omfattande lokal miljöpåverkan. Det har också visats att de geologiska förutsättningarna för HT-BTES är goda på många platser i Göteborg, även om lokala förhållanden kan skilja sig åt. För att nå lönsamhet för HT-BTES-systemet krävs en avvägning på utformning av lagret för att nå hög urladdad temperatur utan att investeringskostnaden blir för stor. Undersökningen visar att om anslutning av HT-BTES-systemet kan ske mot befintlig anslutningspunkt eller till befintlig värmepanna kan investeringskostnaden minska och därmed lönsamheten öka. Placering av HT-BTES-systemet i områden med risk för överföringsbegränsningar kan också minska behovet av att förstärka fjärrvärmenätet, och således bidra till att minska de kostnader som förstärkning av nätet innebär. Betydelsefulla parametrar för att nå lönsamhet för HT-BTES-system inkluderar dessutom kostnaden för inlagrad värme liksom vilket vinstkrav som kan accepteras. Tillgång till HT-BTES möjliggör ökad nyttjandegrad och flexibilitet för fjärrvärmeproduktionsenheter, och därmed ökad anpassningsmöjlighet till förändrade förutsättningar på värmemarknaden. Dock återstår att visa att komponenter som klarar de höga temperaturkraven kan tillverkas till acceptabel kostnad. HT-BTES BTES TES High Temperature Borehole Duct Thermal Energy Storage District Heating Seasonal Storage Storage Pellet Heat Plant Energy Power Flow Martes Environmental impact Finance Investment Cost Technology Drilling Saving Gothenburg Heat Transfer Bedrock Review Feasibility Study Load Peak load Base load District Heating Production Network Grid Pipe Borehole Heat exchanger Collector New Future Generation Low temperature Bottle neck System Successive calculation Matlab Computor programming Science HT-BTES BTES TES Borrhålslager Säsongslager Fjärrvärme Martes Värmelager Pellets Panna Energi Effekt Flöde Miljöpåverkan Ekonomi Investeringskostnad Teknik Borrning Besparing Göteborg Värmeöverföring Berggrund Review Förstudie Borrhål Last Spetslast Baslast Fjärrvärmeproduktion Hög temperatur Produktion Nät Rör Kollektor Borrhålsvärmeväxlare Ny Framtid Generation Låg temperatur Flaskhals System Successive kalkylering Matlab Data programmering Vetenskap
227	Kondenzační technika a odvody spalin / Condensing technology and flue gas Müller, Jan January 2014 (has links) This thesis is developed as a proposal for heating for a primary school and kindergarten in the region of Brno-countryside. For the insulated building, a combination of heating and air-conditioning is proposed. The concept is designed so that the air-conditioning preheats the exterior air and the heating system warms the incoming air to a comfortable temperature. For the required thermal performance, sources of heat (for gas and pellets) and a layout solution for the boiler room is designed. Drainage of combustion products is proposed for both solutions. The project solution is per the extent of the construction permit. The theoretical part is linked with the practical part through the condensation boilers, their function and division, and drainage of combustion products. The experiment for the given topic was conducted on the drainage of combustion products. The pressure loss of the reverse knob was determined in relation to the flow rate of air in the condensation boilers as this loss is essential in assessing the drainage of combustion products.

Page generated in 0.0582 seconds